Stainless Steel dealers in UAE

2205 / 1.4462 / UNS S32205 Duplex Stainless Steel | Supplier in UAE & GCC

2205 / 1.4462 / UNS S32205 — 22Cr duplex stainless: about twice the yield strength of 316L, PREN 34+, chloride SCC resistance; offshore, marine, process.

Industries Served

Oil & Gas
Marine
Petrochemical
Food Processing
Power Generation

Overview

2205 duplex stainless steel (UNS S32205 / S31803, EN 1.4462 / X2CrNiMoN22-5-3, ASTM A182 F51 / F60) is a nitrogen-alloyed austenitic-ferritic stainless steel containing 22.0–23.0% chromium, 4.5–6.5% nickel, 3.0–3.5% molybdenum and 0.14–0.20% nitrogen. Solution annealed at 1020–1100°C and water quenched, it has a balanced microstructure of roughly half ferrite and half austenite, which gives about twice the yield strength of 316L — 450 MPa minimum to ASTM A479 / A240 — together with high resistance to chloride stress corrosion cracking. A pitting resistance equivalent (PREN = Cr + 3.3Mo + 16N) of 34 or more provides much better pitting and crevice corrosion resistance than 316L in seawater-splash, brine and chloride process service, and the grade is acceptable for sour service within NACE MR0175 / ISO 15156-3 limits. It is covered by ASTM A276, A479, A240 and A182, EN 10088-2 / -3 and NORSOK M-630 MDS D44 / D45 / D47; no AMS or MIL specification applies. Service is limited to about 316°C because of 475°C embrittlement, and it welds well with ER2209 filler. Typical uses are offshore piping, valves and pump shafts, heat exchangers, pressure vessels and desalination equipment.

Nifty Alloys supplies 2205 / 1.4462 duplex stainless steel from stock in Dubai, UAE, in round bar, flat bar, plate and forgings, solution annealed and dual-certified UNS S31803 / S32205. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, mechanical properties, ferrite content and, on request, ASTM A923 intermetallic-phase and corrosion test results; EN 10204 3.2 third-party inspection and NORSOK M-630 compliant supply are available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and specification to request a quote — quotations are turned around the same day.

Chemical Composition

0.02 %
C

Carbon

≤ 0.03 %

1.5 %
Mn

Manganese

≤ 2 %

0.5 %
Si

Silicon

≤ 1 %

P

Phosphorus

≤ 0.03 %

S

Sulfur

≤ 0.02 %

22.5 %
Cr

Chromium

22 – 23 %

5.7 %
Ni

Nickel

4.5 – 6.5 %

3.2 %
Mo

Molybdenum

3 – 3.5 %

0.17 %
N

Nitrogen

0.14 – 0.2 %

35 %
PREN

calculated

≥ 34 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM A479 / A479M

ASTM

Revision: ASTM A479 / A479M — current edition

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels — covers 316 / 316L in the annealed condition and Type 316 / 316L in strain-hardened Level 1 (S1) and Level 2 (S2) conditions.

ASME equivalent: SA-479 (ASME BPVC Section II Part A). General requirements per ASTM A484. Strain-hardened bar is marked S1 or S2 after the grade designation.

Available Forms

Flat Bar

5–100 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Forging

100–1000 mm. Forged rings, discs and blocks to order. [VERIFY — supply range not confirmed]

Plate / Block

3–100 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

10–450 mm. Diameter, solution annealed, peeled / ground. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Solution Annealed, dual-certified UNS S31803 / S32205. ASTM A923, NORSOK M-630 and NACE MR0175 documentation on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM A479 / A479M

Designations & Equivalents

StandardDesignationNotes
UNSS32205Current, tighter designation — primary chemistry on this page
UNSS31803Original designation — met by dual-certified S32205 material
EN / Werkstoff1.4462EN 10088 material number
EN NameX2CrNiMoN22-5-3EN 10088 steel name
ASTMA182 F51 / F60Forging designations (F51 = S31803, F60 = S32205)
Common NameM-630 MDS D44 / D45 / D47(NORSOK) 22Cr duplex forgings / plates / bars
BS318S13Former British designation
JISSUS329J3LJapanese Industrial Standard
Common NameZ3CND22-05Az(AFNOR) French designation
AMSNoneNo AMS / MIL specification applies to 2205
Common NameDuplex 2205 / 22Cr duplex / duplex stainless steel / F51 / F60Buyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, mechanical properties, ferrite content.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156SuitableDuplex stainless steel (PREN 30–40, solution annealed, about 35–65% ferrite) acceptable under ISO 15156-3 within the environmental limits of the applicable table (temperature, H2S partial pressure, chloride, pH) — confirm against project conditions [VERIFY — exact limits per current edition].
NORSOK M-630 MDS D44 / D45 / D47ConditionalSupplied to NORSOK MDS requirements on request (including impact, ferrite, microstructure and ASTM G48 corrosion testing) — specify product and MDS at order stage.
ASTM A923ConditionalMethods A / B / C testing on request.
ASME Section II / VIIISuitableSA-240 / SA-479 / SA-182 material for Section VIII Div. 1 to 316°C.

Specifications

Mechanical Properties

Values per ASTM A479 / A479M. Bar length compares conditions within each row.

PropertySolution Annealed | ASTM A479
Tensile Strength (UTS)655 MPaminASTM A479 / A276, solution annealedSpecified minimum (A240 plate: 655 MPa).
Yield Strength (0.2% Proof Stress)450 MPaminASTM A479 / A276Specified minimum (A240: 450 MPa).
Elongation25 %minASTM A479 / A276, 50 mm gaugeSpecified minimum.
Hardness290 HBmaxASTM A479Specified maximum (A240 plate: 293 HB / 31 HRC).
Impact Energy (Charpy V-notch)45 JminNORSOK MDS D47 bars, -46°CNORSOK requirement when specified (axial and tangential) [VERIFY — test temperature per MDS revision].
Ferrite Content35–65 %Base metalTypical specified range for oil and gas supply (NORSOK / project spec).

Physical Properties

PropertySolution Annealed | ASTM A479
Densityat 20°C7.8 g/cm³
Modulus of Elasticityat 20°C200 GPa
Thermal Conductivityat 20°C19 W/m·K
Coefficient of Thermal Expansionat 20–100°C13 µm/m·°C
Electrical Resistivityat 20°C0.8 µΩ·m

Service Conditions

Service Temperature

Min -50 °CMax 316 °C

Notes

ASME Section VIII Div. 1 permits use to 316°C (600°F); EN design data typically to 250–300°C. Long exposure above about 300°C causes 475°C embrittlement, and 700–950°C causes sigma / chi phase precipitation. Good impact toughness to about -40 / -50°C; specify impact testing for lower temperatures.

Corrosion Performance

PREN 35

General corrosion

Excellent resistance to chloride stress corrosion cracking — far superior to 304 / 316. Good resistance to organic acids and many inorganic acids. Acceptable in sour service within NACE MR0175 / ISO 15156-3 limits. Intermetallic phases from incorrect heat treatment or welding reduce corrosion resistance — ASTM A923 testing detects them.

Pitting resistance

Critical pitting temperature typically about 25–35°C in ASTM G48 Method A ferric chloride testing (compared with about 10–15°C for 316L). Good resistance to pitting and crevice corrosion in seawater-splash, brines and chloride process streams; for immersion in warm seawater, super duplex is preferred.

PREN notes

PREN = Cr + 3.3Mo + 16N ≈ 34–36 for S32205 (316L ≈ 24–26).

Heat Treatment

HEAT TREATMENT GUIDE — 2205 / 1.4462 / UNS S32205 / S31803

Supply condition: solution annealed at 1020–1100°C and rapidly water quenched — balanced ferrite-austenite structure (about 40–60% ferrite), free of intermetallics. Not hardenable by heat treatment — strength comes from the duplex structure and nitrogen; can be strengthened by cold work. Avoid the 300–1000°C range in service and fabrication: 475°C embrittlement (about 300–525°C) and sigma / chi precipitation (about 700–950°C) reduce toughness and corrosion resistance. Hot forming: about 1150–950°C, followed by full solution annealing and rapid cooling. Stress relief: not normally performed in the 300–1000°C range; full solution annealing is the only recommended heat treatment after heavy forming or repair. Welding: no preheat or PWHT; control heat input and interpass temperature (see 7.8).

ENGINEERING NOTES
Weldability
Good

Readily welded by GTAW, GMAW, SMAW, FCAW and SAW using over-alloyed 2209 fillers (extra nickel to restore phase balance in the weld). No preheat or PWHT normally required. Control heat input (typically about 0.5–2.5 kJ/mm) and keep interpass temperature below about 150°C to avoid excessive ferrite (low heat input) or intermetallic precipitation (high heat input). Use Ar + N2 shielding / backing gas to protect weld nitrogen. Ferrite in weld and HAZ is typically specified at 30–65%.

Filler metals
  • ER2209 · AWS A5.9 / TIG (GTAW) / MIG (GMAW)Standard over-alloyed duplex filler (about 9% Ni)
  • E2209-16 / -17 · AWS A5.4 / SMAWCovered electrode for 2205
  • E2209T0-1 / T1-1 · AWS A5.22 / FCAWFlux-cored wire for positional and high-deposition welding
  • ER2594 · AWS A5.9 / TIG / MIGSuper-duplex filler for higher-strength or root passes where specified
Machinability
Fair

More difficult to machine than 316L because of its higher strength and work hardening. Use rigid set-ups, sharp positive-rake carbide tooling, lower cutting speeds than for austenitic grades (about 20–30% lower) with adequate feed to stay below the work-hardened layer, and generous coolant.

Applications

  • Offshore and onshore oil and gas piping, manifolds and flowline components
  • Valve bodies, stems and trim (A182 F51 / F60 forgings)
  • Pump shafts, impellers and seawater pump components
  • Heat exchangers, shell-and-tube bundles and pressure vessels
  • Desalination plants and seawater cooling systems in the GCC
  • Chemical and petrochemical process equipment in chloride media
  • Marine hardware, shafting and deck fittings
  • Pulp and paper digesters and bleach plant equipment
  • Food processing and brine-handling equipment
  • Structural and architectural components needing high strength and corrosion resistance

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

2205 duplex is used where high strength and chloride corrosion resistance are needed together: offshore and onshore oil and gas piping, manifolds and valves, pump shafts, heat exchangers, pressure vessels, desalination plants, seawater cooling systems and chemical process equipment. In the UAE and GCC it is one of the most widely specified stainless steels for oil and gas, desalination and marine projects.

Get in touch

Elevateyourprojectswithoursuperiorsteel