Stainless Steel dealers in UAE

904L / 1.4539 / UNS N08904 Super Austenitic Stainless Steel | Supplier in UAE & GCC

904L / 1.4539 / UNS N08904 — 20Cr-25Ni-4.5Mo-1.5Cu super austenitic stainless: excellent sulphuric and phosphoric acid resistance, PREN about 35.

Industries Served

Petrochemical
Oil & Gas
Marine
Power Generation
Food Processing

Overview

904L stainless steel (UNS N08904, EN 1.4539 / X1NiCrMoCu25-20-5, ASTM A276 / A479 / A240, A182 F904L) is a high-alloy, extra-low-carbon super austenitic stainless steel containing 19.0–23.0% chromium, 23.0–28.0% nickel, 4.0–5.0% molybdenum and 1.0–2.0% copper, with carbon held to 0.020% maximum. It was developed for dilute and medium-concentration sulphuric acid: the combination of high nickel, molybdenum and copper gives far better resistance than 316L in sulphuric, phosphoric and acetic acids and other reducing media. Its pitting resistance equivalent (PREN = Cr + 3.3Mo + 16N) of about 34–36 also gives much better pitting and crevice-corrosion resistance than 316L in chloride environments, very good resistance to chloride stress corrosion cracking thanks to its high nickel, and freedom from intergranular corrosion after welding because of its very low carbon. In the solution-annealed condition it provides 220 MPa minimum yield and 490 MPa minimum tensile strength (ASTM A479 / A240), or 230 MPa and 530–730 MPa to EN 10088-3. It is fully austenitic, non-magnetic and readily formed and welded. Typical uses are sulphuric- and phosphoric-acid plant, chemical and pharmaceutical process equipment, heat exchangers, seawater-cooled condensers, flue-gas cleaning and pulp-and-paper equipment.

Nifty Alloys supplies 904L / 1.4539 stainless steel from Dubai, UAE, in round bar and plate, solution annealed, with EN / ASTM dual certification on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry and mechanical properties; EN 10204 3.2 third-party inspection and NACE MR0175 / MR0103 compliance statements are available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.015 %
C

Carbon

≤ 0.02 %

0.4 %
Si

Silicon

≤ 1 %

1.5 %
Mn

Manganese

≤ 2 %

P

Phosphorus

≤ 0.045 %

S

Sulfur

≤ 0.035 %

20 %
Cr

Chromium

19 – 23 %

25 %
Ni

Nickel

23 – 28 %

4.5 %
Mo

Molybdenum

4 – 5 %

1.5 %
Cu

Copper

1 – 2 %

N

Nitrogen

≤ 0.1 %

35 %
PREN

calculated

≥ 34 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM A479 / A479M

ASTM

Revision: ASTM A479 / A479M — current edition

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels — covers 316 / 316L in the annealed condition and Type 316 / 316L in strain-hardened Level 1 (S1) and Level 2 (S2) conditions.

ASME equivalent: SA-479 (ASME BPVC Section II Part A). General requirements per ASTM A484. Strain-hardened bar is marked S1 or S2 after the grade designation.

Available Forms

Plate / Block

3–60 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

10–300 mm. Diameter, solution annealed (EN properties to 250 mm). [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Solution Annealed [VERIFY — stock status]; EN / ASTM dual certification on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM A479 / A479M

Designations & Equivalents

StandardDesignationNotes
AISI / SAE904L(AISI / ASTM) ASTM A276 / A479 / A240 grade
UNSN08904Unified Numbering System — primary chemistry
EN / Werkstoff1.4539EN 10088 material number
EN NameX1NiCrMoCu25-20-5EN 10088 steel name
ASTMA182 F904LForging / flange grade designation
ASTMB625Plate / sheet / strip (nickel-alloy product standard) — aliases only
BS904S13Former British designation
Common Name2562(SS) Swedish standard
Common NameZ2NCDU25-20(AFNOR) French designation
JISSUS890LJapanese Industrial Standard (nearest)
Common NameNone(AMS / MIL) No AMS or MIL specification applies to 904L
Common NameAlloy 904L / SS 904L / super austenitic stainless / acid-resistant stainlessBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and mechanical properties.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156SuitableHighly alloyed austenitic stainless (solution annealed) acceptable under ISO 15156-3 within the environmental limits of the applicable table [VERIFY — current edition].
NACE MR0103 / ISO 17945SuitableRefinery sour service — solution annealed, per MR0103.
PED 2014/68/EU (EN 10028-7)ConditionalPressure-purpose plate to EN 10028-7 on request.
ASME Section II / VIIISuitableSA-240 / SA-479 material for pressure equipment.

Specifications

Mechanical Properties

Values per ASTM A479 / A479M. Bar length compares conditions within each row.

PropertySolution Annealed | ASTM A479
Tensile Strength (UTS)490 MPaminASTM A479 / A276 / A240Specified minimum (EN: 530–730 MPa).
Yield Strength (0.2% Proof Stress)220 MPaminASTM A479 / A276 / A240Specified minimum (EN: 230 MPa).
Elongation35 %min50 mm gaugeSpecified minimum.
Hardness90 HRBmaxASTM A240 plateSpecified maximum (EN guidance 230 HB).
Impact Energy (Charpy V-notch)100 JminEN 10088-3 +AT, room temp, longitudinalEN minimum.

Physical Properties

PropertySolution Annealed | ASTM A479
Densityat 20°C8 g/cm³
Modulus of Elasticityat 20°C195 GPa
Thermal Conductivityat 20°C12 W/m·K
Coefficient of Thermal Expansionat 20–100°C15.8 µm/m·°C
Specific Heat Capacityat 20°C450 J/kg·K
Electrical Resistivityat 20°C1 µΩ·m

Service Conditions

Service Temperature

Min -196 °CMax 400 °C

Notes

EN 10088-3 gives proof stress at temperature to 400°C; ASME pressure design is typically limited to about 370–400°C. Prolonged exposure at about 600–1000°C can precipitate intermetallic phases. Fully austenitic and tough to cryogenic temperatures.

Corrosion Performance

PREN 35

General corrosion

Excellent resistance to sulphuric acid (especially in the medium concentration range), phosphoric and acetic acids and other reducing media; very good chloride SCC resistance and no intergranular corrosion after welding. Acceptable in sour service within NACE MR0175 / ISO 15156-3 limits.

Pitting resistance

Much better pitting and crevice resistance than 316L / 317L; resists seawater at moderate temperatures, but for warm or stagnant seawater 6Mo or super duplex grades are preferred.

PREN notes

PREN = Cr + 3.3Mo + 16N ≈ 34–36 — compared with about 25 for 316L and 43 for 6Mo (S31254).

Heat Treatment

HEAT TREATMENT GUIDE — 904L / 1.4539 / UNS N08904

Supply condition: solution annealed at about 1090–1175°C and rapidly water quenched — fully austenitic. Not hardenable by heat treatment — strength increased only by cold work. Hot forming: heat to about 1150–1180°C, work down to about 900°C, then solution anneal and quench. Avoid prolonged exposure at about 600–1000°C (intermetallic precipitation); re-solution anneal if affected. Welding: no preheat or PWHT required.

ENGINEERING NOTES
Weldability
Good

Readily welded by GTAW, GMAW, SMAW and SAW without preheat or PWHT. Use matching ER385 / E385 filler, or over-alloyed ERNiCrMo-3 for the most corrosive service. The fully austenitic weld is prone to hot cracking — keep heat input low, interpass temperature below about 100–150°C and minimise restraint. Very low carbon prevents sensitisation.

Filler metals
  • ER385 · AWS A5.9 / TIG (GTAW) / MIG (GMAW)Matching 904L filler
  • E385-16 · AWS A5.4 / SMAWMatching covered electrode
  • ERNiCrMo-3 · AWS A5.14 / TIG / MIGOver-alloyed Ni-base filler for the most corrosive service
  • 20 25 5 Cu N L · EN ISO 14343European matching filler designation
Machinability
Fair

Moderate machinability (about 35–45% of B1112) — high nickel and work hardening require rigid set-ups, sharp positive-rake carbide tools, lower speeds than 316L, steady feed and generous coolant.

Applications

  • Sulphuric-acid production, storage and handling equipment
  • Phosphoric-acid and fertiliser plant in the GCC
  • Chemical and pharmaceutical process vessels, reactors and piping
  • Heat exchangers and seawater-cooled condensers
  • Flue-gas desulphurisation and gas-cleaning equipment
  • Pulp-and-paper bleaching and digester components
  • Oil and gas process equipment and sour-service components (within NACE limits)
  • Desalination and brine-handling equipment
  • Electrostatic precipitators and pickling-plant equipment
  • Valves, pumps and flanges (A182 F904L)

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

904L is used where acid and chloride corrosion are too severe for 316L: sulphuric- and phosphoric-acid plant, chemical and pharmaceutical process equipment, heat exchangers, seawater-cooled condensers, flue-gas cleaning, pulp and paper, and oil and gas process equipment. In the UAE and GCC it is used in fertiliser, petrochemical and desalination plants.

Get in touch

Elevateyourprojectswithoursuperiorsteel