Stainless Steel dealers in UAE

316 / 316L / 1.4401 Stainless Steel | Supplier in UAE & GCC

316 / 316L (1.4401 / 1.4404) — molybdenum-bearing austenitic stainless steel with PREN ~24, low-carbon weldability and dual-certified bar and forging supply.

Industries Served

Oil & Gas
Petrochemical
Marine
Food Processing
Medical
Power Generation
Manufacturing
Construction

Overview

316 / 316L stainless steel (UNS S31600 / S31603, EN 1.4401 / 1.4404, X5CrNiMo17-12-2 / X2CrNiMo17-12-2, JIS SUS316 / SUS316L) is a molybdenum-bearing austenitic chromium-nickel stainless steel and the most widely specified grade for chloride-bearing process, offshore and coastal service. The 2.0–3.0% molybdenum addition stabilises the passive film against chloride attack, raising the pitting resistance equivalent number (PREN) to approximately 24, compared with 18–19 for 304, while 10–14% nickel keeps the structure fully austenitic, non-magnetic in the annealed condition and tough down to −196°C. 316L limits carbon to 0.030% maximum, which prevents chromium carbide precipitation at grain boundaries when weld heat-affected zones pass through the 450–850°C sensitisation range, so heavy sections can be welded without post-weld solution treatment. Bar is normally dual-certified, meeting 316L chemistry together with the 316 mechanical minimums of 515 MPa tensile and 205 MPa 0.2% proof strength per ASTM A479 and A276. The grade cannot be hardened by heat treatment — strength above the annealed level is obtained only by cold working, as in ASTM A479 strain-hardened bar.

Nifty Alloys supplies 316 / 316L stainless steel from stock in Dubai, UAE, as dual-certified round bar, flat bar, plate / block and open-die or ring forgings, in the solution annealed and strain-hardened conditions to ASTM A276, ASTM A479 / ASME SA-479, ASTM A182 F316 / F316L, ASTM A240 and EN 10088-3 / EN 10272. Every delivery is certified to EN 10204 3.1 as standard and fully traceable to mill source, with EN 10204 3.2 third-party inspection available on request; material compliant with NACE MR0175 / ISO 15156 or AMS 5648 / AMS 5653 can be supplied when specified at order stage. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe on request. Contact our team to request a quote for 316 / 316L — same-day quotation is standard.

Chemical Composition

0.02 %
C

Carbon

≤ 0.03 %

0.45 %
Si

Silicon

≤ 1 %

1.4 %
Mn

Manganese

≤ 2 %

P

Phosphorus

≤ 0.045 %

S

Sulfur

≤ 0.03 %

16.8 %
Cr

Chromium

16 – 18 %

10.1 %
Ni

Nickel

10 – 14 %

2.05 %
Mo

Molybdenum

2 – 3 %

0.05 %
N

Nitrogen

≤ 0.1 %

Fe

Iron

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM A479 / A479M

ASTM

Revision: ASTM A479 / A479M — current edition [VERIFY — confirm edition year at entry]

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels — covers 316 / 316L in the annealed condition and Type 316 / 316L in strain-hardened Level 1 (S1) and Level 2 (S2) conditions.

ASME equivalent: SA-479 (ASME BPVC Section II Part A). General requirements per ASTM A484. Strain-hardened bar is marked S1 or S2 after the grade designation.

Available Forms

Flat Bar

Standard flats and plate-cut flats on request — thickness and width to order. [VERIFY — confirm range against current stock list]

Forging / Ring Forging

Open-die forgings and seamless rolled rings to ASTM A182 F316 / F316L per customer drawing — size on enquiry.

Plate / Block

6–150 mm. Thickness. Plate to ASTM A240; saw-cut or plasma-cut blocks and blanks to size. [VERIFY — confirm range against current stock list]

Round Bar

10–300 mm. Diameter. Solution annealed, hot-rolled / peeled or cold-drawn finish. Strain-hardened bar per ASTM A479 is defined only up to 76.2 mm (Level 2) — larger sizes Level 1 only. [VERIFY — confirm range against current stock list]

Stock & delivery

Stock location
Dubai, UAE
In stock
Solution annealed, dual-certified 316 / 316L (default stock condition). Strain-hardened ASTM A479 Level 1 / Level 2 bar and forgings to ASTM A182 supplied on request. [VERIFY — confirm stocked conditions with stock team]
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

ASTM A479 / A479M

Designations & Equivalents

StandardDesignationNotes
AISI / SAE316Primary designation — standard-carbon version (C ≤ 0.08%)
AISI / SAE316LLow-carbon version (C ≤ 0.030%) — weldable without sensitisation
UNSS31600Unified Numbering System — Type 316
UNSS31603Unified Numbering System — Type 316L
EN / Werkstoff1.4401European material number — 316 (primary DIN/EN designation for this page)
EN / Werkstoff1.4404European material number — 316L
EN NameX5CrNiMo17-12-2EN 10088 chemical designation — 1.4401
EN NameX2CrNiMo17-12-2EN 10088 chemical designation — 1.4404
BS316S31 / 316S11British Standard (legacy BS 970 / BS 1449) — 316 / 316L
JISSUS316 / SUS316LJapanese Industrial Standard
ISOX5CrNiMo17-12-2 / X2CrNiMo17-12-2ISO 15510 designations
ASTMA276 / A479 / A182 F316, F316L / A240Bar, pressure bar, forgings, plate
ASMESA-479 / SA-182 / SA-240ASME BPVC Section II Part A equivalents
AMSAMS 5648 / AMS 5653Aerospace bar and forging specifications — 316 / 316L
Common NameSS316, SS316L, 316/316L, A4 stainless, marine grade stainless, 18/10 MoTrade and buyer search terms. "A4" is the ISO 3506 fastener class for 316-type steel.

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableMill Test Certificate provided as standard with every delivery.
EN 10204 3.2ConditionalAvailable on request — specify at order stage; third-party inspection adds lead time.
NACE MR0175 / ISO 15156ConditionalSolution annealed condition only: hardness ≤ 22 HRC and free of cold work intended to enhance mechanical properties. Use within the environmental limits of ISO 15156-3 Table A.2 (temperature and H2S partial pressure). Strain-hardened bar (SpecSheet 2) is NOT acceptable.
NACE MR0103ConditionalAcceptable in the solution annealed condition with hardness ≤ 22 HRC. Not applicable to strain-hardened bar.
AMS 5648Requires ConfirmationType 316 bar / forgings to aerospace specification — confirm availability and certification at order stage.
AMS 5653Requires ConfirmationType 316L bar / forgings to aerospace specification — confirm availability and certification at order stage.
ASME SA-479 / SA-182SuitableBar and forgings dual-stamped ASTM / ASME for coded pressure equipment when ordered.
PED 2014/68/EUConditionalApplies to European pressure-equipment orders when bar is ordered and certified to EN 10272.

Specifications

Mechanical Properties

Values per ASTM A479 / A479M. Bar length compares conditions within each row.

PropertySolution Annealed | ASTM A479 / A276Strain Hardened | ASTM A479
Tensile Strength (UTS)515 MPaminTypical 580 MPaRoom temp, longitudinal — ASTM A479 / A276Dual 316 / 316L and 316. 316L-only certification: 485 min. A182 F316: 515; F316L: 485. A240 plate: 515 / 485. Typical value = typical.–
Yield Strength (0.2% Proof Stress)205 MPaminTypical 290 MPaRoom temp, longitudinal — ASTM A479 / A276316L-only certification: 170 min. A182 F316: 205; F316L: 170. Typical value = typical.–
Elongation30 %minTypical 50 %50 mm (2 in) or 4D — ASTM A479ASTM A276 Condition A requires 40% min; A182: 30% min; A240: 40% min. Typical value = typical.–
Reduction of Area40 %minTypical 65 %Longitudinal — ASTM A479ASTM A276 and A182: 50% min. Typical value = typical.–
Hardness215 HBmaxTypical 160 HBSurface — EN 10088-3 +ATEN 10088-3 max 215 HB. ASTM A240 plate: 217 HB max. NACE MR0175: 22 HRC max. ASTM A276 / A479 annealed bar: no Brinell max specified for 316 / 316L [VERIFY]. Typical value = typical.–SurfaceNo hardness requirement in ASTM A479 for strain-hardened 316. Report if required by purchase order. Typical hardness not confirmed [VERIFY — source not confirmed]. May exceed the 22 HRC NACE limit.
Tensile Strength (Rm) — EN500–700 MPaTypical 580 MPaRoom temp — EN 10088-3 / EN 10272 +AT, d ≤ 160 mm1.4401 and 1.4404. Typical value = typical.–
Yield Strength (Rp0.2) — EN200 MPaminTypical 280 MPaRoom temp — EN 10088-3 / EN 10272 +AT, d ≤ 160 mm1.4401 and 1.4404. Typical value = typical.–
Elongation (A) — EN40 %minTypical 50 %Longitudinal — EN 10088-3 +AT, d ≤ 160 mm160–250 mm: 30% min (transverse). Typical value = typical.–
Impact Energy (Charpy) — EN100 JminTypical 200 JRoom temp, V-notch, longitudinal — EN 10088-3 +AT, d ≤ 160 mmTransverse: 60 J min. Typical value = typical; typically > 60 J retained at −196°C.–
Tensile Strength (UTS) — Level 1–585 MPaminRoom temp, longitudinal — all sizesASTM A479 strain-hardened Level 1 (S1), 316 / 316L.
Yield Strength (0.2% Proof Stress) — Level 1–450 MPaminRoom temp, longitudinal — all sizesBars over 50.8 mm: 415 MPa min permitted when tested on a cross-section.
Elongation — Level 1–30 %min50 mm (2 in) or 4DASTM A479 Level 1.
Reduction of Area — Level 1–60 %minLongitudinalASTM A479 Level 1.
Tensile Strength (UTS) — Level 2–655 MPamind ≤ 50.8 mm50.8–63.5 mm: 620 min; 63.5–76.2 mm: 550 min.
Yield Strength (0.2% Proof Stress) — Level 2–515 MPamind ≤ 50.8 mm50.8–63.5 mm: 450 min; 63.5–76.2 mm: 380 min.
Elongation — Level 2–25 %mind ≤ 50.8 mm, 50 mm or 4D50.8–76.2 mm: 30% min.
Reduction of Area — Level 2–40 %minLongitudinal, all Level 2 sizesASTM A479 Level 2.

Physical Properties

PropertySolution Annealed | ASTM A479 / A276Strain Hardened | ASTM A479
Densityat 20°C8 g/cm³–
Modulus of Elasticityat 20°C193 GPa–
Thermal Conductivityat 100°C16.3 W/m·K–
Coefficient of Thermal Expansionat 20–100°C16 µm/m·°C–
Specific Heat Capacityat 20°C500 J/kg·K–
Melting Point / Rangeat Solidus–liquidus1375 °C–
Electrical Resistivityat 20°C0.74 µΩ·m–
Magnetic Permeabilityat 20°C1.02 µr–
ISO 9001:2015at Quality Management System — procurement, stock management, supply.–2026 Check current certificate
AEO (Authorised Economic Operator)at Customs compliance for UAE and GCC trade.––UAE Federal Customs Authority
1at Corrected — combined page per approved-slugs.md–316 Combined 316 / 316L page with S31603 / 1.4404 / X2CrNiMo17-12-2 in aliases
2at Corrected–316 "Marine grade" kept as buyer term; limits in submerged / warm seawater stated (PREN ~24), duplex recommended — consistent with the PREN blog
3at Omitted — confirm whether pipe / sheet pages are needed separately––Claims pipes and sheets are supplied
4at Replaced––Title, meta description and URL lack UAE, DIN/EN and form signals; URL under /products/
5at Could not compare — check old values against this document before go-live––Specification tab values (composition, mechanical, physical) — not rendered on fetch

Service Conditions

Service Temperature

Min -196 °CMax 816 °C

Notes

Fully austenitic structure has no ductile-to-brittle transition, so 316 / 316L retains impact toughness at −196°C (LNG and cryogenic service). Upper limit of 816°C reflects the ASME Section II-D allowable stress range for 316 in pressure service; oxidation resistance extends to about 870°C intermittent / 925°C continuous in air [typical]. 316L is limited to about 425–454°C in ASME pressure design because of its lower strength [VERIFY — confirm against ASME II-D / B31.3 edition in use]. Prolonged exposure at 550–900°C can precipitate sigma phase and, for standard-carbon 316, carbides that reduce corrosion resistance and toughness — specify 316H or 316Ti for sustained creep service.

Corrosion Performance

PREN 24

General corrosion

Resists most organic acids, dilute sulphuric acid at moderate temperature, phosphoric acid, alkalis and sulphite environments better than 304. Not resistant to hydrochloric acid, hydrofluoric acid or hot concentrated sulphuric acid. 316L passes ASTM A262 Practice E intergranular testing in the as-welded condition. Pickle and passivate fabricated parts to remove free iron, heat tint and embedded contamination.

Pitting resistance

Good resistance to pitting in fresh water, potable water, marine atmospheres and low-chloride process streams. Susceptible to pitting and crevice corrosion in stagnant or warm seawater (above ~30°C), under deposits and in tight crevices — not recommended for long-term submerged Gulf seawater service. Chloride stress corrosion cracking is a risk above about 60°C in chloride-containing environments [typical]; specify duplex 2205 or super duplex for hot chloride service.

PREN notes

PREN = %Cr + 3.3 × %Mo + 16 × %N. Minimum-chemistry PREN ≈ 23; typical heats 24–26. Compare 304 ≈ 18–19, 2205 duplex ≈ 35, super duplex ≥ 40.

Heat Treatment

ProcessTemperatureCoolingResult & notes
HEAT TREATMENT GUIDE316 / 316L / 1.4401: Solution annealing: 1040–1120°C (ASTM A479 minimum 1040°C; EN 10088-3 range 1020–1120°C)hold long enough for full recrystallisation and carbide dissolution (guide: 30 min minimum, about 1 hour per 25 mm of section [typical])water quench, or rapid air cool for thin sections — result: fully austenitic, non-magnetic, maximum corrosion resistance; hardness ≤ 215 HB (EN 10088-3). Hardening: Not possible by heat treatment. 316 / 316L can be strengthened only by cold working (ASTM A479 strain-hardened Level 1 / Level 2). Stress relieving: 316L only — 850–900°C for about 1 hour, then air cool, for dimensional stability after heavy machining or welding [typical]; low-temperature stress relief below 400°C where only partial relief is acceptable. Do not stress relieve standard-carbon 316 in the 450–850°C range — sensitisation risk. Hot working / forging: Start at 1150–1260°C, finish above about 930°C [typical], then solution anneal to restore corrosion resistance (mandatory for ASTM A182 forgings). Avoid: Prolonged exposure at 550–900°C (sigma phase and carbide precipitation). Re-annealing or welding strain-hardened bar removes its cold-work strength.
ENGINEERING NOTES
Weldability
Excellent

Readily welded by GTAW (TIG), GMAW (MIG), SMAW and FCAW. No preheat required; keep interpass temperature at or below 150°C to limit time in the sensitisation range and control distortion. No PWHT is required for 316L — its 0.030% maximum carbon prevents intergranular carbide precipitation in the heat-affected zone. For standard-carbon 316 in heavy sections destined for aggressive service, specify 316L or solution anneal after welding. Use matching 316L filler with 3–10 FN delta ferrite to resist hot cracking. Remove heat tint and scale by pickling and passivation to restore corrosion resistance. Welding strain-hardened bar anneals the heat-affected zone and locally removes the cold-work strength.

Filler metals
  • ER316L · AWS A5.9 / TIG (GTAW)Matching filler for 316 and 316L — preferred for root passes and critical joints. EN ISO 14343: W 19 12 3 L
  • ER316LSi · AWS A5.9 / MIG (GMAW)Higher silicon improves wetting and bead profile in MIG welding. EN ISO 14343: G 19 12 3 L Si
  • E316L-16 / E316L-17 · AWS A5.4 / SMAWRutile-coated stick electrodes for site and positional welding. EN ISO 3581: E 19 12 3 L R
  • E316LT1-1 / E316LT1-4 · AWS A5.22 / FCAWFlux-cored wire for high-deposition fabrication welding
  • ER309LMo · AWS A5.9 / TIG-MIG (dissimilar)For joining 316 / 316L to carbon or low-alloy steel — over-alloyed to tolerate dilution
Machinability
Fair

Machine in the solution annealed condition. 316 / 316L work-hardens rapidly — use sharp, positive-rake carbide tooling, rigid set-ups and a constant, positive feed; never allow the tool to dwell or rub. Typical turning speeds with coated carbide are about 150–200 m/min roughing [typical]. Use generous flood coolant. Strain-hardened bar machines with less built-up edge but higher cutting forces. Machinability is roughly 20–25% lower than 304 because of the higher nickel and molybdenum content [typical].

Applications

  • Valve bodies, stems, seats and trim for sweet and mildly sour oil & gas service
  • Instrument fittings, manifolds and needle-valve bodies machined from bar for offshore platforms
  • Weld-neck flanges, nozzles and ring forgings to ASTM A182 F316L for petrochemical vessels
  • Heat exchanger tubesheets, baffles and channel covers in UAE refinery and chemical plants
  • Product-water and low-chloride brine handling components in GCC desalination and water treatment plants
  • Pump shafts, impellers and agitator shafts for chemical dosing and process pumps
  • Hygienic tank fittings, valve bodies and CIP-cleaned parts for food and dairy processing
  • Pharmaceutical reactor internals and sanitary fittings requiring low-carbon weld zones
  • Marine deck hardware, propeller shafting and fasteners for above-waterline and coastal service
  • Cryogenic valve components and LNG equipment parts requiring impact toughness at −196°C
  • Architectural fixings, balustrade posts and cladding brackets for coastal construction in Dubai and Abu Dhabi
  • High-strength studs, bolting and shafts from ASTM A479 strain-hardened Level 1 / Level 2 bar

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

316 / 316L stainless steel is used for valves, pump shafts, flanges, heat exchanger parts, instrument fittings and process equipment exposed to chlorides, mild acids and marine atmospheres. Its 2.0–3.0% molybdenum content gives better pitting resistance than 304, so it is the default grade for oil & gas topside components, petrochemical vessels, food and pharmaceutical plant, and coastal construction fixings. In the UAE and GCC it is widely specified for refinery, desalination product-water and offshore instrumentation service. The low-carbon 316L version is chosen wherever the part will be welded.

Get in touch

Elevateyourprojectswithoursuperiorsteel