Bronze dealers in UAE

C63000 / CuAl10Ni5Fe4 / 2.0966 Nickel Aluminium Bronze | Supplier in UAE & GCC

C63000 / CuAl10Ni5Fe4 / 2.0966 — wrought nickel aluminium bronze: up to 760 MPa (AMS 4640), seawater and wear resistant; bushes, valves, aircraft gear.

Industries Served

Marine
Oil & Gas
Aerospace & Defence
Heavy Engineering
Power Generation

Overview

C63000 nickel aluminium bronze (EN CuAl10Ni5Fe4 / CW307G; formerly DIN 2.0966; BS CA104; AMS 4640; JIS C6301) is the most widely used wrought NAB, containing 9.0–11.0% aluminium, 4.0–5.5% nickel and 2.0–4.0% iron, with up to 1.5% manganese and copper the remainder. Aluminium provides high strength and a protective alumina film, while nickel and iron refine the structure and raise strength, toughness and resistance to seawater corrosion, cavitation, erosion and de-aluminification, without reducing ductility. The result is a bronze with strength comparable to alloy steels, outstanding wear and galling resistance against steel under heavy loads, good fatigue strength and low magnetic permeability. Drawn and stress relieved (HR50) high-strength bar to AMS 4640 gives 760 MPa minimum tensile and 470 MPa yield up to 25 mm, falling to 690 / 345 MPa above 76 mm, with 10% elongation and typically 212–302 HB; as-extruded (M30) bar to ASTM B150 gives 550–585 MPa tensile. It resists scaling at elevated temperature and performs well in seawater, brackish water and many acids. Typical uses are aircraft landing-gear bushes and bearings, hydraulic and earth-moving equipment bushes, valve seats, stems and balls, pump shafts and impellers, gears and cams, heat-exchanger tubesheets and headers, and marine propulsion components.

Nifty Alloys supplies C63000 nickel aluminium bronze from Dubai, UAE, in round bar, flat bar, plate and hollow bar — HR50 drawn and stress relieved as standard and M30 as-extruded on request — with AMS 4640 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and temper to request a quote — quotations are turned around the same day.

Chemical Composition

81 %
Cu

Copper

10 %
Al

Aluminium

9 – 11 %

5 %
Ni

Nickel

4 – 5.5 %

3 %
Fe

Iron

2 – 4 %

Mn

Manganese

≤ 1.5 %

Si

Silicon

≤ 0.25 %

Sn

Tin

≤ 0.2 %

Zn

Zinc

≤ 0.3 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM B150 / B150M

ASTM

Revision: ASTM B150 / B150M — current edition

Standard specification for aluminium bronze rod, bar, and shapes. Covers C61300, C61400, C62300, C63000, C63200, and other wrought aluminium bronze alloys.

Primary North American standard for C63200 wrought bar and rod. Specifies chemical composition, mechanical properties, and temper designations. Most widely referenced for aluminium bronze bar in UAE and GCC oil & gas and marine procurement.

Available Forms

Flat Bar

6–75 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Hollow Bar

30–300 mm. Outside diameter; range of bores. [VERIFY — stock range not confirmed]

Plate / Block

6–150 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

10–250 mm. Diameter, HR50 to about 127 mm, M30 larger. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
HR50 bar and hollow bar [VERIFY — stocked forms]; M30, plate and AMS 4640 certified material on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM B150 / B150M

Designations & Equivalents

StandardDesignationNotes
UNSC63000Primary chemistry (ASTM B150 / AMS 4640)
EN NameCuAl10Ni5Fe4EN 12163 designation
EN / WerkstoffCW307G(EN Number) EN numerical designation
DIN2.0966Former German number (DIN 17665 / 17672)
BSCA104BS 2874 wrought designation
Common NameBS B23 / DTD 197A(UK Aerospace) UK aerospace specifications — aliases only
AMSAMS 4640Bars, rods, shapes, tubes, forgings (Module 2)
Common NameQQ-C-465 / SAE J463 / SB-150 / SB-171(Federal / SAE / ASME) Legacy federal, SAE and ASME equivalents — aliases only
Common NameJIS C6301 / ISO 428 / GB QAl10-4-4 / NES 833(Other) National / naval equivalents — aliases only
Common NameAB2 (BS 1400) / CC333G / C95800(Cast reference) Cast counterparts — reference only, not equivalents of wrought C63000
Common NameNAB / nickel aluminium bronze / CDA 630 / C630 / AMS 4640 bronzeBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, temper, mechanical properties and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
AMS 4640ConditionalSupplied to AMS 4640 (HR50 or TQ50) on request — confirm revision.

Specifications

Mechanical Properties

Values per ASTM B150 / B150M. Bar length compares conditions within each row.

PropertyHR50 Drawn & Stress Relieved | ASTM B150M30 As-Extruded | ASTM B150
Tensile Strength (UTS)760 MPaminRounds ≤ 50 mmAMS 4640 minimum (110 ksi).585 MPaminRounds 50–100 mm / shapesASTM B150 minimum (85 ksi).
Tensile Strength (UTS)690 MPaminRounds 76–127 mmAMS 4640 minimum (100 ksi); yield 345 MPa.550 MPaminRounds > 100 mmASTM B150 minimum (80 ksi); yield 275 MPa, El. 12%.
Yield Strength (0.5% Ext.)470 MPaminRounds ≤ 25 mmAMS 4640 minimum (68 ksi); 415 MPa for 25–50 mm.295 MPaminRounds 50–100 mm / shapesASTM B150 minimum (42.5 ksi).
Elongation10 %min4DAMS 4640 minimum.10 %min4DASTM B150 minimum.
Hardness212–302 HBHR50Typical range.–

Physical Properties

PropertyHR50 Drawn & Stress Relieved | ASTM B150M30 As-Extruded | ASTM B150
Densityat 20°C7.58 g/cm³7.58 g/cm³
Modulus of Elasticityat 20°C117 GPa117 GPa
Thermal Conductivityat 20°C39 W/m·K39 W/m·K
Coefficient of Thermal Expansionat 20–300°C16.2 µm/m·°C16.2 µm/m·°C
Specific Heat Capacityat 20°C377 J/kg·K377 J/kg·K
Electrical Conductivityat 20°C7 % IACS7 % IACS

Service Conditions

Service Temperature

Min -196 °CMax 400 °C

Notes

Retains high strength at elevated temperature (to about 400°C) and resists scaling; good toughness at sub-zero temperatures. Melting range about 1040–1055°C.

Corrosion Performance

General corrosion

Good resistance to de-aluminification (selective phase corrosion), many acids and alkalis, and oxidation. In stagnant or crevice seawater conditions a temper anneal (about 675°C) optimises microstructure; for US naval service with controlled microstructure, C63200 is specified.

Pitting resistance

Excellent resistance to seawater, brackish water, cavitation and erosion — superior to non-nickel aluminium bronzes.

Additional notes

Not applicable — PREN is not used for copper alloys.

Heat Treatment

HEAT TREATMENT GUIDE — C63000 / CuAl10Ni5Fe4 / 2.0966

Supply: HR50 (drawn and stress relieved) or M30 (as hot extruded); AMS 4640 also TQ50 (temper annealed). Temper anneal: about 675°C (1250°F) for several hours — improves corrosion resistance and stabilises the microstructure. Stress relieving: about 300–400°C after machining. Hot working: about 800–925°C — readily hot worked; cold working limited. Not recommended: soldering, oxy-acetylene welding, heavy cold working.

ENGINEERING NOTES
Weldability
Good

Welded by GTAW and GMAW using nickel-aluminium-bronze filler (ERCuNiAl); clean thoroughly and use AC TIG or DCEP MIG because of the alumina film. Soldering, oxy-acetylene welding and heavy cold working are not recommended. A post-weld anneal (about 675°C) restores corrosion resistance in critical seawater service.

Filler metals
  • ERCuNiAl · AWS A5.7 / TIG (GTAW) / MIG (GMAW)Nickel-aluminium-bronze filler — matching composition
  • ECuNiAl · AWS A5.6 / SMAWNAB covered electrode
  • ERCuMnNiAl · AWS A5.7 / TIG / MIGManganese-NAB filler — alternative for repairs
Machinability
Fair

Machinability about 30% of free-cutting brass. Use rigid set-ups, sharp carbide tooling, positive rake and coolant; the alloy work hardens moderately.

Applications

  • Aircraft landing-gear bushes, strut bearings and trunnion bearings (AMS 4640)
  • Hydraulic and earth-moving equipment bushes and wear plates
  • Valve seats, stems, balls and guides for oil and gas and marine service
  • Pump shafts, impellers and wear rings in seawater
  • Gears, worm wheels, cams and gear-shift forks
  • Heat-exchanger tubesheets, flanges and headers (ASTM B171 plate)
  • Marine propulsion components and fittings for GCC vessels
  • Desalination and seawater piping components
  • Non-sparking and low-magnetic tools and parts
  • Offshore and subsea structural members and fasteners

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

C63000 is used for aircraft landing-gear bushes and bearings, hydraulic and earth-moving equipment bushes, valve seats, stems and balls, pump shafts and impellers, gears and cams, heat-exchanger tubesheets and headers, and marine propulsion components. In the UAE and GCC it is the most widely used bronze for heavy-duty marine, oil and gas and equipment-maintenance parts.

Get in touch

Elevateyourprojectswithoursuperiorsteel