Carbon Steel dealers in UAE

EN8 / 080M40 / C45 Carbon Steel | Supplier in UAE & GCC

EN8 (080M40 / C45) — medium-carbon engineering steel: 550–620 MPa min normalised, up to 850 MPa Q&T, 50–55 HRC induction hardened surface; shafts and axles.

Industries Served

Manufacturing
Automotive
Heavy Engineering
Construction
Oil & Gas
Mining

Overview

EN8 (BS 970 080M40, closely related to EN C45 / C45E 1.1191, exact chemistry match C40 / 1.0511, AISI 1040 / 1045) is an unalloyed medium-carbon engineering steel with 0.36–0.44% carbon and 0.60–1.00% manganese, supplied in Europe to EN ISO 683-1 (formerly EN 10083-2) and EN ISO 683-7 for bright bar. Carbon in this range gives roughly 50% more strength than mild steel while keeping good machinability: in the normalised condition the ferrite-pearlite structure delivers 550–620 MPa minimum tensile strength and 152–207 HB. Because it has no alloying additions, hardenability is limited, so quenching and tempering is effective only in modest sections — BS 970 Condition R (700–850 MPa) is limited to about 19 mm and Condition Q (625–775 MPa) to about 63 mm. Where wear resistance is needed, flame or induction hardening produces a 50–55 HRC surface over a tough core. These properties make EN8 the default choice for shafts, axles, pins, studs, gears and general machine parts.

Nifty Alloys supplies EN8 / 080M40 / C45 carbon steel from stock in Dubai, UAE, in round bar, flat bar, square bar, hexagonal bar and plate / block, in the normalised condition as standard, bright drawn to EN ISO 683-7, and quenched and tempered to order. Material is cut to length and dispatched with EN 10204 3.1 Mill Test Certificates as standard, stating the exact chemistry, condition and mechanical results with full traceability to the mill; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.4 %
C

Carbon

0.36 – 0.44 %

Si

Silicon

0.1 – 0.4 %

Mn

Manganese

0.6 – 1 %

P

Phosphorus

≤ 0.05 %

S

Sulfur

≤ 0.05 %

Cr

Chromium

≤ 0.4 %

Mo

Molybdenum

≤ 0.1 %

Ni

Nickel

≤ 0.4 %

Cr + Mo + Ni

≤ 0.63 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 683-1

Other

Revision: EN ISO 683-1:2018

Available Forms

Flat Bar

10–100 mm. Thickness; width × thickness to order or cut from plate. [VERIFY — stock range not confirmed]

Hexagonal Bar

10–100 mm. Across flats, bright drawn. [VERIFY — stock range not confirmed]

Plate / Block

10–200 mm. Thickness; blocks saw-cut to size. [VERIFY — stock range not confirmed]

Round Bar

10–400 mm. Diameter, normalised / turned; bright drawn typically 10–100 mm. [VERIFY — stock range not confirmed]

Square Bar

20–200 mm. Across flats. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Normalised (+N) — standard stocked condition. Bright Drawn (+C) per current stock list. Quenched & Tempered (+QT / BS 970 Condition Q or R) on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 683-1

Designations & Equivalents

StandardDesignationNotes
BSEN8Original BS 970:1955 designation — primary buyer term
BS080M40BS 970 designation (withdrawn standard) — 0.36–0.44% C
BS080M46BS 970 designation for the 0.42–0.50% C variant — matches C45
EN NameC45E / C45EN ISO 683-1 (formerly EN 10083-2) — closely related grade, commonly supplied for EN8 duty; 0.42–0.50% C
EN / Werkstoff1.1191 / 1.0503C45E / C45 material numbers
EN NameC40 / C40EExact EN chemistry match for 080M40 (0.37–0.44% C)
EN / Werkstoff1.0511 / 1.1186C40 / C40E material numbers
DINCk45 / Ck40Former DIN designations
AISI / SAE1045 / 1040Nearest US grades — ASTM A29
ASTMA29 (1045)US general bar standard — alias only
JISS45C / S40CJapanese Industrial Standard
Common Name40C8(IS) Indian Standard IS 1570
Common NameEN8 round bar / EN8 steel / medium carbon steel / 40 carbon steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — states 080M40 or C45E chemistry, condition and mechanical results.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.

Specifications

Mechanical Properties

Values per EN ISO 683-1. Bar length compares conditions within each row.

PropertyNormalised (+N) | EN ISO 683-1Bright Drawn (+C) | EN ISO 683-7Quenched & Tempered (+QT) | EN ISO 683-1
Tensile Strength (UTS)620 MPaminC45E — up to 16 mmEN ISO 683-1 minimum.710–1030 MPaOver 10 to 16 mmEN ISO 683-7 range. 750–1050 MPa for 5–10 mm.700–850 MPaC45E — up to 16 mmEN ISO 683-1 range.
Tensile Strength (UTS)580 MPaminC45E — over 16 to 100 mmEN ISO 683-1 minimum.650–1000 MPaOver 16 to 40 mmEN ISO 683-7 range.650–800 MPaC45E — over 16 to 40 mmEN ISO 683-1 range.
Tensile Strength (UTS)560 MPaminC45E — over 100 to 250 mmEN ISO 683-1 minimum.630–900 MPaOver 40 to 63 mmEN ISO 683-7 range.630–780 MPaC45E — over 40 to 100 mmEN ISO 683-1 range.
Tensile Strength (UTS)550 MPamin080M40 — up to 150 mmBS 970 reference (withdrawn standard). 510 MPa min over 150–250 mm.580–850 MPaOver 63 to 100 mmEN ISO 683-7 range.625–775 MPa080M40 Condition Q — up to 63 mmBS 970 reference.
Tensile Strength (UTS)––700–850 MPa080M40 Condition R — up to 19 mmBS 970 reference.
Yield Strength (ReH)340 MPaminC45E — up to 16 mmEN ISO 683-1 minimum.–385 MPamin080M40 Condition QBS 970 reference; Condition R: 465 MPa min.
Yield Strength (ReH)305 MPaminC45E — over 16 to 100 mmEN ISO 683-1 minimum.––
Yield Strength (ReH)275 MPaminC45E — over 100 to 250 mmEN ISO 683-1 minimum.––
Yield Strength (ReH)280 MPamin080M40 — up to 150 mmBS 970 reference. 245 MPa min over 150–250 mm.––
Elongation14 %minA (5.65√So) — up to 16 mmEN ISO 683-1 minimum; 16% over 16 mm.7 %minA — over 16 to 40 mmEN ISO 683-7 minimum; 6% at 10–16 mm, 8% over 40 mm.16 %minC45E — over 16 to 40 mmEN ISO 683-1 minimum; 14% up to 16 mm, 17% over 40 mm. BS 970 Q / R: 16%.
Hardness152–207 HB080M40 — up to 150 mmBS 970 reference range; 146–197 HB over 150–250 mm.200–298 HBOver 16 to 40 mmFor information — converted from tensile range.179–229 HB080M40 Condition QBS 970 reference; Condition R: 201–255 HB.
Yield Strength (0.2% Proof Stress)–500 MPaminOver 10 to 16 mmEN ISO 683-7 minimum. 565 MPa for 5–10 mm.490 MPaminC45E — up to 16 mmEN ISO 683-1 minimum; 430 MPa over 16–40 mm, 370 MPa over 40–100 mm.
Yield Strength (0.2% Proof Stress)–410 MPaminOver 16 to 40 mmEN ISO 683-7 minimum.–
Yield Strength (0.2% Proof Stress)–360 MPaminOver 40 to 63 mmEN ISO 683-7 minimum.–
Yield Strength (0.2% Proof Stress)–310 MPaminOver 63 to 100 mmEN ISO 683-7 minimum.–
Reduction of Area––40 %minC45E — over 16 to 40 mmEN ISO 683-1 minimum; 35% up to 16 mm, 45% over 40 mm.
Impact Energy (Charpy V-notch)––25 JminC45E — room temp, KVEN ISO 683-1 minimum for C45E / C45R. BS 970 Q / R: 28 J (KCV).

Physical Properties

PropertyNormalised (+N) | EN ISO 683-1Bright Drawn (+C) | EN ISO 683-7Quenched & Tempered (+QT) | EN ISO 683-1
Densityat 20°C7.85 g/cm³7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C210 GPa210 GPa210 GPa
Thermal Conductivityat 20°C50 W/m·K50 W/m·K50 W/m·K
Coefficient of Thermal Expansionat 20–100°C11.5 µm/m·°C11.5 µm/m·°C11.5 µm/m·°C
Specific Heat Capacityat 20°C460 J/kg·K460 J/kg·K460 J/kg·K
Electrical Resistivityat 20°C0.19 µΩ·m0.19 µΩ·m0.19 µΩ·m

Service Conditions

Service Temperature

Max 350 °C

Notes

[VERIFY — maxServiceTempC 350: continuous load-bearing limit not confirmed in a code source] Medium-carbon steel loses strength progressively above about 300°C, and creep becomes significant above about 400°C; it is not a pressure-equipment or elevated-temperature grade. Do not use quenched-and-tempered parts above the tempering temperature. Low-temperature toughness is limited — normalised EN8 has no guaranteed impact value, so specify Q&T C45E with a Charpy requirement for sub-zero service.

Corrosion Performance

General corrosion

Unsuitable for seawater, chloride, acidic or chemical service without coating. Store under cover and oiled. For corrosive duty, consider a stainless or nickel alloy grade instead.

Pitting resistance

Not corrosion resistant — rusts in humid and coastal atmospheres, including typical UAE and GCC conditions. Protect with oil, paint, galvanising, phosphating or hard chrome plating as appropriate.

Additional notes

No corrosion resistance. Surface protection required.

Heat Treatment

HEAT TREATMENT GUIDE — EN8 / 080M40 / C45

Forging: 850–1100°C; do not forge below 850°C; cool slowly. Normalising: 840–880°C — soak until uniform — cool in still air — 152–207 HB, refined grain. Soft annealing: 650–700°C — furnace cool — max 207 HB (+A) for heavy machining or cold forming. Hardening: 820–860°C — soak about 30 min per 25 mm — quench in water (sections over about 25 mm) or oil (small or complex sections). Tempering: 550–660°C — 1 h per 25 mm minimum — air cool — BS 970 Condition R (700–850 MPa) up to about 19 mm; Condition Q (625–775 MPa) up to about 63 mm. Temper immediately after quenching. Flame / induction hardening: surface to 50–55 HRC from normalised or Q&T stock; temper at 150–200°C after hardening. Stress relieving: 550–650°C — 1 h per 25 mm — slow cool; use after heavy machining or welding. Limiting ruling section: as a non-alloy steel EN8 does not through-harden in large sections — heat treat after rough machining to get better core properties.

ENGINEERING NOTES
Weldability
Fair

Weldable with precautions. Carbon at 0.36–0.50% gives a carbon equivalent of roughly 0.5–0.65, so the heat-affected zone can harden and crack if cooled quickly. Preheat to 150–250°C (higher end for sections over 25 mm), maintain interpass at or above preheat, use low-hydrogen consumables and cool slowly. Stress relieve at 550–650°C after welding wherever possible. Avoid welding quenched-and-tempered or induction-hardened parts, which will soften or crack in the HAZ. [VERIFY — preheat range per section to be confirmed against the welding procedure]

Filler metals
  • E7018 · AWS A5.1 / SMAWLow-hydrogen electrode — bake per manufacturer; standard choice with preheat
  • ER70S-6 · AWS A5.18 / MIG (GMAW)Solid wire for general fabrication welds
  • ER70S-2 · AWS A5.18 / TIG (GTAW)Root passes and repair welds
Machinability
Good

Machines well in the normalised and bright drawn conditions (152–207 HB normalised). HSS tooling is adequate for general turning and drilling; carbide is preferred for production runs and for Q&T material up to 255 HB. Bright drawn bar machines to close tolerance with minimal stock removal. Annealed (+A, max 207 HB) material can be specified for heavy machining.

Applications

  • Drive shafts, line shafts and spindles for pumps, gearboxes and conveyors
  • Axles, wheel shafts and stub axles for trailers and material-handling equipment
  • Studs, bolts, pins and threaded rod for general engineering assemblies
  • Gears, sprockets and pinions that are induction hardened on the teeth
  • Hydraulic cylinder rods and rams before chrome plating
  • Couplings, flanges and hubs for rotating equipment in GCC process plants
  • Keys, keyways stock and wear strips machined from bright flat and square bar
  • Crankshafts, connecting rods and levers for light and medium-duty machinery
  • Rollers, guide pins and bushings for mining and quarry equipment
  • Base plates, brackets and fixtures for fabrication shops in the UAE
  • Turned fasteners and nuts from bright hexagonal bar

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

EN8 steel is used for shafts, axles, spindles, studs, bolts, pins, gears and general machine parts that need more strength than mild steel without the cost of an alloy steel. In the normalised condition it gives 550–620 MPa minimum tensile strength, and it can be induction hardened to 50–55 HRC on wearing surfaces. In the UAE and GCC it is the most widely ordered carbon engineering steel for pump shafts, couplings, hydraulic rods and fabrication-shop components.

Get in touch

Elevateyourprojectswithoursuperiorsteel