Carbon Steel dealers in UAE

S355 / S355JR / S355J2 Structural Steel | Supplier in UAE & GCC

S355 / S355JR / S355J2 — EN 10025-2 high-yield structural steel: 355 MPa yield, excellent weldability, J2 impact at −20°C; plate, flat and round bar.

Industries Served

Construction
Heavy Engineering
Oil & Gas
Power Generation

Overview

S355 structural steel (EN 10025-2 S355JR / J0 / J2 / K2, material numbers 1.0045 / 1.0553 / 1.0577 / 1.0596; formerly DIN St 52-3 and BS 4360 50B–50D; nearest ASTM A572 Grade 50) is a non-alloy carbon-manganese structural steel with a minimum yield strength of 355 MPa in thicknesses up to 16 mm — falling progressively to 345 MPa (16–40 mm), 335 MPa (40–63 mm), 315 MPa (80–100 mm) and 275 MPa (200–250 mm) — and a tensile strength of 470–630 MPa from 3 to 100 mm. The quality suffix defines guaranteed Charpy V-notch toughness: JR 27 J at +20°C, J0 27 J at 0°C, J2 27 J at −20°C and K2 40 J at −20°C, so J2 or K2 is specified where low-temperature toughness matters. With carbon of 0.20% maximum (J2) and a carbon equivalent (CEV) of 0.45% maximum up to 30 mm, it has excellent weldability by all common processes, along with good formability and machinability. It offers about 30% higher yield strength than S275, allowing lighter structures. As a carbon steel it needs surface protection — painting or hot-dip galvanising (Si 0.14–0.25% for zinc-coating class 3). Typical uses are building frames and bridges, offshore and onshore structures, pressure-vessel supports, cranes and lifting equipment, earth-moving and mining machinery, wind-tower components and general fabrication.

Nifty Alloys supplies S355 / S355JR / S355J2 structural steel from Dubai, UAE, in plate, flat bar and round bar, as rolled or normalised, with flame-cut profiles to drawing on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, CEV, tensile and impact results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and sub-grade to request a quote — quotations are turned around the same day.

Chemical Composition

0.17 %
C

Carbon

≤ 0.2 %

0.3 %
Si

Silicon

≤ 0.55 %

1.4 %
Mn

Manganese

≤ 1.6 %

P

Phosphorus

≤ 0.025 %

S

Sulfur

≤ 0.025 %

Cu

Copper

≤ 0.55 %

N

Nitrogen

CEV

calculated

≤ 0.45 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10025-2

Other

Revision: EN 10025-2:2019

Available Forms

Flat Bar

10–100 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Plate / Block

6–150 mm. Thickness; flame-cut to size / profile. [VERIFY — stock range not confirmed]

Round Bar

20–300 mm. Diameter, hot rolled. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
S355J2+N / S355JR plate and bar [VERIFY — stocked sub-grades and sizes]; K2 and flame-cut profiles on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces and profiles available

Key standards

EN 10025-2

Designations & Equivalents

StandardDesignationNotes
EN NameS355JR / S355J0 / S355J2 / S355K2EN 10025-2 quality sub-grades
EN / Werkstoff1.0045 / 1.0553 / 1.0577 / 1.0596(EN Number) JR / J0 / J2 / K2 material numbers
EN NameS355J2G3 / S355J2G4 / S355K2G3(EN (legacy)) EN 10025:1990 designations — superseded
DINSt 52-3DIN 17100 — legacy
BS4360 50B / 50C / 50DBS 4360 — legacy (JR / J0 / J2 approx.)
ASTMA572 Grade 50Commonly accepted substitute — 345 MPa yield, different chemistry; nearest only
Common NameS355N / NL (EN 10025-3), S355M / ML (EN 10025-4), S355G (EN 10225), S355J2H (EN 10210 / 10219)(Related (separate standards)) Fine-grain, offshore and hollow-section grades — not equivalents
Common NameNone(AMS / MIL) No AMS or MIL specification applies (carbon steel)
Common NameS355 plate / S355J2 plate / high yield steel / St52 / structural steel plateBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, CEV, tensile and impact (sub-grade).

Specifications

Mechanical Properties

Values per EN 10025-2. Bar length compares conditions within each row.

PropertyAs-Rolled / +N | EN 10025-2
Yield Strength (ReH)355 MPamin≤ 16 mmEN 10025-2 minimum (345 MPa 16–40 mm; 275 MPa 200–250 mm).
Tensile Strength (UTS)470–630 MPa3–100 mmEN 10025-2 range (450–600 MPa 100–250 mm).
Elongation22 %min≤ 40 mm, longitudinalEN 10025-2 minimum.
Impact Energy (Charpy V-notch)27 Jmin−20°C (J2)JR +20°C; J0 0°C; K2 40 J at −20°C.
Hardness160 HBtypicalAs-rolledTypical (about 145–190 HB) — information only.

Physical Properties

PropertyAs-Rolled / +N | EN 10025-2
Densityat 20°C7.85 g/cm³
Modulus of Elasticityat 20°C210 GPa
Thermal Conductivityat 20°C50 W/m·K
Coefficient of Thermal Expansionat 20–100°C12 µm/m·°C
Specific Heat Capacityat 20°C460 J/kg·K

Service Conditions

Service Temperature

Min -20 °CMax 300 °C

Notes

Minimum design temperature depends on sub-grade and thickness (EN 1993-1-10): J2 / K2 tested at −20°C, J0 at 0°C, JR at +20°C. Not intended for elevated-temperature pressure service [VERIFY upper limit].

Corrosion Performance

General corrosion

Rusts in humid and coastal atmospheres — protect by painting systems or hot-dip galvanising (Si-controlled material). Store under cover in the UAE climate.

Pitting resistance

Not applicable — carbon steel.

Additional notes

No corrosion resistance. Surface protection required.

Heat Treatment

HEAT TREATMENT GUIDE — S355 / S355JR / S355J2

Delivery: as rolled (+AR) or normalised / normalised rolled (+N). Normalising: about 890–950°C, air cool [VERIFY]. Stress relieving after welding: about 550–600°C [VERIFY] — confirm per design code. Not intended for quenching and tempering. Hot forming: about 1050–850°C, followed by normalising where +N properties must be retained. Flame-cut edges may harden locally — grind before bending or welding where required.

ENGINEERING NOTES
Weldability
Excellent

Readily welded by all common processes (SMAW, GMAW, FCAW, SAW). CEV max (J2, ladle): 0.45 (≤ 30 mm), 0.47 (30–150 mm), 0.49 (150–250 mm). Preheat may be required for thick sections, high restraint or low ambient temperature — determine per EN 1011-2.

Filler metals
  • E7018 · AWS A5.1 / SMAWLow-hydrogen electrode — structural welds (E7018-1 for J2 / K2 toughness)
  • ER70S-6 · AWS A5.18 / MIG (GMAW)Solid MIG wire
  • E71T-1 · AWS A5.20 / FCAWFlux-cored wire for positional welding
  • F7A2-EM12K · AWS A5.17 / SAWSubmerged-arc wire / flux combination
Machinability
Good

Good machinability and cold formability for a structural steel; suitable for flame, plasma and laser cutting.

Applications

  • Building frames, columns, beams and connections
  • Bridges and civil-engineering structures
  • Onshore and offshore oil and gas structures and skids
  • Cranes, lifting beams and load-handling equipment
  • Earth-moving, mining and quarrying machinery
  • Wind-tower and power-plant structural components
  • Tanks, silos and pressure-vessel supports
  • Trailer, chassis and transport structures
  • Flame-cut base plates, gussets and brackets
  • General steel fabrication across GCC projects

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

S355 is used for building frames and bridges, onshore and offshore structures, cranes and lifting equipment, earth-moving and mining machinery, wind-tower components, tanks and silos, trailers and general steel fabrication. In the UAE and GCC it is the standard high-yield structural steel for construction and oil and gas projects.

Get in touch

Elevateyourprojectswithoursuperiorsteel