Carbon Steel dealers in UAE

S275JR / 1.0044 Structural Steel | Supplier in UAE & GCC

S275JR / 1.0044 — EN 10025-2 general structural steel: 275 MPa yield, excellent weldability and formability, 27 J at +20°C; plate and flat bar.

Industries Served

Construction
Heavy Engineering
Manufacturing

Overview

S275JR structural steel (EN 10025-2, material number 1.0044; formerly DIN St 44-2, BS 4360 43B and EN 10025 Fe 430 B; nearest ASTM A36 and JIS SS400) is a non-alloy, low-carbon carbon-manganese structural steel with a minimum yield strength of 275 MPa up to 16 mm — falling progressively to 265 MPa (16–40 mm), 255 MPa (40–63 mm), 235 MPa (80–100 mm) and 205 MPa (200–250 mm) — and a tensile strength of 410–560 MPa from 3 to 100 mm. The JR quality guarantees a Charpy V-notch impact energy of 27 J at +20°C, so it is used where low-temperature toughness is not required. With carbon of 0.21% maximum, manganese of 1.50% maximum and a carbon equivalent (CEV) of 0.40% maximum up to 40 mm, it has excellent weldability by all common processes, usually without preheat, and very good cold formability for bending, folding and flanging. It is stronger than S235 and more economical than S355 where design loads allow. As a carbon steel it needs surface protection by painting or hot-dip galvanising. Typical uses are building frames, beams and columns, light structural steelwork, platforms and walkways, brackets and base plates, machinery frames, trailers and general fabrication.

Nifty Alloys supplies S275JR structural steel from Dubai, UAE, in plate and flat bar, as rolled, with flame-cut profiles to drawing on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, CEV, tensile and impact results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.15 %
C

Carbon

≤ 0.21 %

Si

Silicon

1 %
Mn

Manganese

≤ 1.5 %

P

Phosphorus

≤ 0.035 %

S

Sulfur

≤ 0.035 %

N

Nitrogen

≤ 0.012 %

Cu

Copper

≤ 0.55 %

CEV

calculated

≤ 0.4 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10025-2

Other

Revision: EN 10025-2:2019

Available Forms

Flat Bar

5–50 mm. Thickness; widths 20–300 mm. [VERIFY — stock range not confirmed]

Plate / Block

5–100 mm. Thickness; flame-cut to size / profile. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
As-rolled plate and flat bar [VERIFY — stocked sizes]; S275J0 / J2 and flame-cut profiles on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces and profiles available

Key standards

EN 10025-2

Designations & Equivalents

StandardDesignationNotes
EN NameS275JREN 10025-2 designation
EN / Werkstoff1.0044(EN Number) EN material number
EN NameS275J0 (1.0143) / S275J2 (1.0145)(EN (other sub-grades)) Lower impact-temperature sub-grades — available on request, not covered by this page
EN NameS275JRG2 / Fe 430 B(EN (legacy)) EN 10025:1990 / 1993 designations — superseded
DINSt 44-2DIN 17100 — legacy
BS4360 43BBS 4360 — legacy
Common NameAFNOR E28-2 / UNE AE275 B / SS 1412 / IS 2062 E250-Fe410(National) National equivalents / near-equivalents
Common NameA36 / SS400(ASTM / JIS (nearest)) Nearest only — A36 yield 250 MPa; SS400 245 MPa; different chemistry control
Common NameNone(AMS / MIL) No AMS or MIL specification applies (carbon steel)
Common NameS275 plate / S275JR mild steel plate / St44 / structural steel plateBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, CEV, tensile and impact.

Specifications

Mechanical Properties

Values per EN 10025-2. Bar length compares conditions within each row.

PropertyAs-Rolled | EN 10025-2
Yield Strength (ReH)275 MPamin≤ 16 mmEN 10025-2 minimum (265 MPa 16–40 mm; 205 MPa 200–250 mm).
Tensile Strength (UTS)410–560 MPa3–100 mmEN 10025-2 range (430–580 MPa < 3 mm).
Elongation23 %min3–40 mm, longitudinalEN 10025-2 minimum.
Impact Energy (Charpy V-notch)27 Jmin+20°C, longitudinalEN 10025-2 minimum (JR).
Hardness122–162 HBAs rolledTypical — information only.

Physical Properties

PropertyAs-Rolled | EN 10025-2
Densityat 20°C7.85 g/cm³
Modulus of Elasticityat 20°C210 GPa
Thermal Conductivityat 20°C50 W/m·K
Coefficient of Thermal Expansionat 20–100°C12 µm/m·°C
Specific Heat Capacityat 20°C460 J/kg·K

Service Conditions

Service Temperature

Min 0 °CMax 300 °C

Notes

JR quality is impact tested at +20°C only — for structures exposed to low temperatures, specify S275J0 / J2 or S355J2. Minimum design temperature per EN 1993-1-10 [VERIFY]. Not intended for elevated-temperature pressure service.

Corrosion Performance

General corrosion

Rusts in humid and coastal atmospheres — protect by painting systems or hot-dip galvanising (Si-controlled material). Store under cover in the UAE climate.

Pitting resistance

Not applicable — carbon steel.

Additional notes

No corrosion resistance. Surface protection required.

Heat Treatment

HEAT TREATMENT GUIDE — S275JR / 1.0044

Delivery: as rolled (+AR); normalised (+N) by agreement. Normalising: about 890–950°C, air cool [VERIFY]. Stress relieving after welding: about 550–600°C where required by design code [VERIFY]. Not intended for quenching and tempering. Hot forming: about 1050–850°C. Flame-cut edges may harden locally — grind before bending where required.

ENGINEERING NOTES
Weldability
Excellent

Readily welded by all common processes (SMAW, GMAW, FCAW, SAW), usually without preheat. CEV max (ladle): 0.40 (≤ 40 mm), 0.42 (> 40 mm). Determine any preheat for thick or highly restrained joints per EN 1011-2.

Filler metals
  • E7018 · AWS A5.1 / SMAWLow-hydrogen electrode — structural welds
  • E6013 · AWS A5.1 / SMAWGeneral-purpose electrode — light fabrication
  • ER70S-6 · AWS A5.18 / MIG (GMAW)Solid MIG wire
  • E71T-1 · AWS A5.20 / FCAWFlux-cored wire for positional welding
Machinability
Good

Good machinability and very good cold formability; suitable for flame, plasma and laser cutting, bending, folding and flanging.

Applications

  • Building frames, beams and columns
  • Light structural steelwork and mezzanine floors
  • Platforms, walkways, stairs and handrails
  • Base plates, gussets, brackets and cleats
  • Machinery frames and equipment bases
  • Trailers, chassis and agricultural equipment
  • Tanks, hoppers and bins (non-pressure)
  • Shop fabrication and laser / plasma-cut parts
  • Signage and street-furniture structures
  • General steel fabrication across GCC projects

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

S275JR is used for building frames, beams and columns, light structural steelwork, platforms and walkways, base plates and brackets, machinery frames, trailers, non-pressure tanks and general fabrication. In the UAE and GCC it is a standard plate and flat-bar grade for construction and shop fabrication.

Get in touch

Elevateyourprojectswithoursuperiorsteel