Alloy Steel dealers in UAE

S690QL / S690QL1 / 1.8928 High Yield Strength Steel | Supplier in UAE & GCC

S690QL / S690QL1 (1.8928) — EN 10025-6 quenched and tempered high-yield structural plate: 690 MPa min yield to 50 mm, impact tested at -40°C / -60°C.

Industries Served

Construction
Heavy Engineering
Oil & Gas
Mining
Automotive
Marine

Overview

S690QL (1.8928) and S690QL1 (1.8988) are high yield strength structural steel plates supplied in the quenched and tempered condition to EN 10025-6 (current edition 2019+A1:2022). Low carbon (0.20% max) combined with controlled additions of manganese, chromium, molybdenum, nickel and micro-alloying elements such as boron, niobium and vanadium gives a fine tempered-martensite / bainite structure after mill water quenching and tempering. The result is a minimum yield strength of 690 MPa up to 50 mm (650 MPa to 100 mm, 630 MPa to 150 mm), tensile strength of 770–940 MPa and 14% minimum elongation — roughly twice the yield strength of S355, allowing much thinner, lighter sections. S690QL is impact tested at -40°C (30 J longitudinal) and S690QL1 at -60°C (30 J). A controlled maximum carbon equivalent (CEV 0.65 up to 50 mm) keeps the plate weldable with appropriate preheat and matching consumables, and it can be cold formed with suitable bend radii. Typical uses are mobile crane booms, lifting equipment, trailer chassis, offshore and bridge structures and heavy mining and earthmoving equipment.

Nifty Alloys supplies S690QL / S690QL1 high yield steel plate from Dubai, UAE, in the quenched and tempered condition to EN 10025-6, as full plates or cut to size. Every plate is dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying ladle chemistry, CEV, tensile results and Charpy impact values at the specified test temperature; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your plate sizes, thickness and quality (QL or QL1) to request a quote — quotations are turned around the same day.

Chemical Composition

C

Carbon

≤ 0.2 %

Si

Silicon

≤ 0.8 %

Mn

Manganese

≤ 1.7 %

P

Phosphorus

≤ 0.02 %

S

Sulfur

≤ 0.01 %

N

Nitrogen

≤ 0.015 %

B

Boron

≤ 0.005 %

Cr

Chromium

≤ 1.5 %

Mo

Molybdenum

≤ 0.7 %

Ni

Nickel

≤ 2 %

Cu

Copper

≤ 0.5 %

Nb

Niobium

≤ 0.06 %

V

Vanadium

≤ 0.12 %

Ti

Titanium

≤ 0.05 %

Zr

Zirconium

≤ 0.15 %

CEV

IIW

≤ 0.65 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10025-6

EN

Revision: EN 10025-6:2019+A1:2022

Hot rolled products of structural steels — Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition. Covers S460 to S960 in Q, QL and QL1 qualities, including S690QL (1.8928) and S690QL1 (1.8988).

Current edition EN 10025-6:2019+A1:2022 (replaced the 2004+A1:2009 edition; originally EN 10137-2). Q = impact tested at -20°C, QL at -40°C, QL1 at -60°C. CE-marking scope under EN 10025-1 for structural use.

Available Forms

Plate / Block

6–150 mm. Thickness; EN 10025-6 properties defined up to 150 mm. Plate widths typically 1500–2500 mm, lengths 6000–12000 mm; cut to size on request. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Quenched & Tempered (+Q) — S690QL (-40°C impact). S690QL1 (-60°C impact) and plates beyond stock thicknesses on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

EN 10025-6

Designations & Equivalents

StandardDesignationNotes
EN NameS690QLEN 10025-6 — impact tested at -40°C
EN / Werkstoff1.8928(EN Number) S690QL steel number
EN NameS690QL1EN 10025-6 — impact tested at -60°C
EN / Werkstoff1.8988(EN Number) S690QL1 steel number
EN NameS690Q / 1.8931Related quality impact tested at -20°C (not stocked unless requested)
EN NameEN 10137-2 S690QL(EN (obsolete)) Superseded standard on older drawings
ASTMA514 — nearest onlyUS quenched and tempered plate, 690 MPa min yield up to 65 mm — different chemistry and test rules; not an exact equivalent
ASTMA709 Grade HPS 100W — nearest onlyUS bridge-steel grade of similar strength — not an exact equivalent
Common NameHigh yield steel plate / high tensile steel plate / Q&T structural plate / 690 MPa plate / S690 plateBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — ladle chemistry, CEV, tensile and Charpy impact at the specified temperature.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Requires ConfirmationNot supplied NACE-certified as standard. EN 10025-6 permits up to 2.0% Ni and does not limit hardness to 22 HRC; ISO 15156-2 requires < 1% Ni and ≤ 22 HRC for pre-qualified low-alloy steels. Confirm heat chemistry, hardness and project requirements before sour-service use.

Specifications

Mechanical Properties

Values per EN 10025-6. Bar length compares conditions within each row.

PropertyQuenched & Tempered | EN 10025-6
Yield Strength (ReH)690 MPaminOver 3 to 50 mmEN 10025-6 minimum.
Yield Strength (ReH)650 MPaminOver 50 to 100 mmEN 10025-6 minimum.
Yield Strength (ReH)630 MPaminOver 100 to 150 mmEN 10025-6 minimum.
Tensile Strength (UTS)770–940 MPaOver 3 to 50 mmEN 10025-6 range.
Tensile Strength (UTS)760–930 MPaOver 50 to 100 mmEN 10025-6 range.
Tensile Strength (UTS)710–900 MPaOver 100 to 150 mmEN 10025-6 range.
Elongation14 %minA (5.65√So), all thicknessesEN 10025-6 minimum.
Impact Energy (Charpy V-notch)30 JminS690QL — longitudinal, -40°CEN 10025-6 minimum (40 J at -20°C, 50 J at 0°C). Transverse: 27 J at -40°C.
Impact Energy (Charpy V-notch)30 JminS690QL1 — longitudinal, -60°CEN 10025-6 minimum (40 J at -40°C, 50 J at -20°C, 60 J at 0°C). Transverse: 27 J at -60°C.

Physical Properties

PropertyQuenched & Tempered | EN 10025-6
Densityat 20°C7.85 g/cm³
Modulus of Elasticityat 20°C210 GPa
Shear Modulusat 20°C81 GPa
Coefficient of Thermal Expansionat 20–100°C12 µm/m·°C

Service Conditions

Service Temperature

Min -40 °CMax 300 °C

Notes

[VERIFY — maxServiceTempC 300: elevated-temperature design limit not confirmed] Minimum service temperature follows the impact-test temperature: S690QL is guaranteed to -40°C and S690QL1 to -60°C; specify QL1 for colder service. EN 10025-6 is a structural steel standard for ambient-temperature design; strength reduces at elevated temperature and service near the tempering temperature must be avoided.

Corrosion Performance

General corrosion

Corrodes like other structural steels. High-strength plate is more susceptible to hydrogen embrittlement — avoid acid pickling and control hydrogen during welding and coating.

Pitting resistance

No pitting resistance. In the humid, coastal UAE and GCC climate, protect with a suitable paint system, metallising or galvanising (check galvanising suitability with the producer for high-strength plate).

Additional notes

Not applicable — low-alloy structural steel.

Heat Treatment

HEAT TREATMENT GUIDE — S690QL / S690QL1 / 1.8928

Supply condition: water quenched and tempered at the mill — properties depend on this treatment; do not re-austenitise or normalise. Hot forming: not recommended — heating above the tempering temperature destroys the Q&T properties. Use cold forming instead. Cold forming: minimum inside bend radius about 3t transverse / 4t longitudinal for t ≤ 16 mm; larger for thicker plates; follow the producer's forming guidance. Thermal cutting: preheat thicker plates before oxy-fuel cutting to avoid edge hardening and cracking. Stress relieving / PWHT: not normally required; if specified, stay at least 25–30°C below the tempering temperature reported on the MTC [VERIFY — confirm with producer]. Welding: control preheat, interpass temperature and heat input per EN 1011-2 to retain HAZ strength and toughness.

ENGINEERING NOTES
Weldability
Good

Weldable with controlled procedures. Determine preheat from plate thickness, carbon equivalent (CEV max 0.65 / 0.77 / 0.83 by thickness band), hydrogen level and heat input using EN 1011-2 — thicker plates typically need preheat of about 75–150°C [VERIFY — project WPS to confirm]. Use low-hydrogen (H5 or better), matching-strength consumables; keep heat input within the range the steel producer recommends to protect HAZ toughness and strength. Avoid excessive heat input and interpass temperatures. Post-weld heat treatment is not normally required; if specified, keep it at least 25–30°C below the plate tempering temperature stated on the MTC [VERIFY].

Filler metals
  • E11018-M · AWS A5.5 / SMAWMatching-strength low-hydrogen electrode; bake per manufacturer
  • ER110S-1 · AWS A5.28 / MIG (GMAW)Matching-strength solid wire
  • E111T1-K3M · AWS A5.29 / FCAWMatching-strength flux-cored wire for positional welding
  • E7018 · AWS A5.1 / SMAWUnder-matching electrode for lower-stressed fillet welds where design permits
Machinability
Fair

Drill and machine with carbide or cobalt HSS tooling at reduced speeds; the Q&T plate is harder than mild steel. Thermal cutting (oxy-fuel, plasma, laser) is routine — preheat thicker plates before flame cutting to avoid edge cracking. Cold forming: minimum inside bend radius about 3t transverse / 4t longitudinal (for t ≤ 16 mm); larger radii for thicker plate.

Applications

  • Mobile and crawler crane booms, jibs and outriggers
  • Lifting equipment, spreader beams and lifting lugs
  • Heavy-haul trailer chassis and low-loader frames
  • Offshore platform and jack-up structural members
  • Bridges and long-span building structures where weight saving matters
  • Mining and earthmoving equipment frames, buckets and booms
  • Hydraulic press frames and heavy machine bases
  • Port handling equipment and container cranes in GCC terminals
  • Wind-turbine and energy-infrastructure structural components
  • Cold-climate and arctic structures (S690QL1, -60°C impact)

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

S690QL is used where high strength allows lighter, thinner structures: mobile crane booms and outriggers, lifting equipment, heavy-haul trailer chassis, offshore and bridge structures, port cranes, and frames and booms for mining and earthmoving equipment. Its 690 MPa minimum yield strength is roughly twice that of S355. In the UAE and GCC it is widely used by crane, trailer and offshore fabricators.

Get in touch

Elevateyourprojectswithoursuperiorsteel