Copper Alloys dealers in UAE

C18200 / CuCr1 / 2.1291 Chromium Copper | Supplier in UAE & GCC

C18200 (CuCr1) — precipitation-hardened chromium copper: 420–470 MPa strength, ~80% IACS conductivity; RWMA Class 2 resistance welding electrode alloy.

Industries Served

Manufacturing
Automotive
Power Generation
Heavy Engineering
Construction
Mould & Die

Overview

C18200 chromium copper (CuCr1, EN CW105C, DIN 2.1291, UNS C18200, RWMA Class 2 / ISO 5182 A2/1) is a precipitation-hardening high-copper alloy containing 0.6–1.2% chromium, supplied to EN 12163 for rod and to the RWMA Class 2 electrode classification. Chromium is almost insoluble in copper at room temperature, so the alloy is solution treated at about 1000°C and water quenched to hold chromium in solid solution, cold drawn, then aged at 425–500°C to precipitate a fine dispersion of chromium particles. Those precipitates pin dislocations and raise strength to 470 MPa minimum (R470, up to 25 mm) and 420 MPa minimum (R420, 25–50 mm), while pulling chromium out of the copper matrix restores conductivity to about 80% IACS typical, 75% IACS minimum. The result is a copper that resists softening and mushrooming at electrode tip temperatures far better than pure copper, which is why CuCr1 is the standard material for resistance welding electrodes, seam-welding wheels, switchgear contacts and high-current hardware.

Nifty Alloys supplies C18200 / CuCr1 chromium copper from Dubai, UAE, in round bar, flat bar and plate / block, in the TH04 solution treated, cold worked and precipitation hardened condition to EN 12163 and RWMA Class 2. Stock bar and plate are cut to length or block size and dispatched with EN 10204 3.1 Mill Test Certificates as standard, reporting certified, traceable chemistry, hardness and electrical conductivity; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa for automotive body shops, fabrication plants and switchgear manufacturers. Send your size list or electrode drawing to request a quote — quotations are turned around the same day.

Chemical Composition

Cu

Copper

0.9 %
Cr

Chromium

0.5 – 1.2 %

Fe

Iron

≤ 0.08 %

Si

Silicon

≤ 0.1 %

Pb

Lead

≤ 0.05 %

Others

total

≤ 0.2 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 12163

EN

Revision: EN 12163 — current edition

Copper and copper alloys - rod for general purposes. European standard covering CuAl10Ni5Fe4 (CW307G) and other copper alloy rod and bar products.

European standard for C63200 / CuAl10Ni5Fe4 wrought rod and bar. CW307G is the EN numeric code for the wrought form. CC333G is the EN casting designation. Also see EN 12167 (profiles) and EN 12168 (hollow sections).

Available Forms

Flat Bar

10–100 mm. Thickness; width × thickness to order. [VERIFY — stock range not confirmed]

Plate / Block

10–100 mm. Thickness; blocks saw-cut to size. [VERIFY — stock range not confirmed]

Round Bar

10–150 mm. Diameter, TH04. Hardness minimum falls with size per RWMA Class 2. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
TH04 Solution Treated, Cold Worked & Precipitation Hardened (EN 12163 / RWMA Class 2) — the only stocked condition. Forms and sizes held in Dubai per current stock list.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 12163

Designations & Equivalents

StandardDesignationNotes
UNSC18200Primary designation — Unified Numbering System
Common NameCDA 182 / C182(CDA) Copper Development Association alloy number
DINCuCr1German / European chemical designation
EN / Werkstoff2.1291German material number
EN NameCuCr1EN 12163 chemical designation
EN / WerkstoffCW105C(EN Number) EN numerical designation
BSCC101Former British Standard (BS 2872 / BS 2874)
Common NameEN 12163(EN Standard) Rod for general purposes — primary European standard
Common NameEN 12164 [VERIFY — CuCr1 listing in EN 12164 not confirmed](EN Standard) Named in the register; CuCr1 is confirmed in EN 12163, EN 12165 and EN 12167
Common NameRWMA Class 2 (Group A)(RWMA) Resistance-welding electrode classification — AWS J1.3
ISOISO 5182 A2/1International electrode material designation
Common NameMIL-C-19311(MIL) Military specification — rod and forgings. Current status not confirmed; aliases only.
AMSNo AMS appliesNo AMS specification covers C18200. AMS 4633 is aluminium silicon bronze (C64200) and does not apply.
ASTMNo ASTM product specificationASTM B441 covers beryllium coppers C17500 / C17510 / C17465 — not C18200. Supplied to EN 12163 / RWMA Class 2.
Common NameChromium copper / chrome copper / CuCr / copper chromium / Class 2 copperBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, hardness and electrical conductivity to EN 12163 / RWMA Class 2.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.

Specifications

Mechanical Properties

Values per EN 12163. Bar length compares conditions within each row.

PropertyTH04 Solution Treated, Cold Worked & Precipitation Hardened | EN 12163
Tensile Strength (UTS)470 MPaminTypical 530 MPaRoom temp — 4 to 25 mm (R470)EN 12163 minimum. Typical value for 12.7 mm TH04 rod.
Tensile Strength (UTS)420 MPaminRoom temp — over 25 to 50 mm (R420)EN 12163 minimum.
Yield Strength (0.2% Proof Stress)380 MPatypicalRoom temp — 4 to 25 mmApproximate value given for information in EN 12163 — not a requirement.
Yield Strength (0.2% Proof Stress)330 MPatypicalRoom temp — over 25 to 50 mmApproximate value given for information in EN 12163 — not a requirement.
Elongation8 %minTypical 16 %A (5.65√So) — 4 to 25 mmEN 12163 minimum (R470).
Elongation12 %minA (5.65√So) — over 25 to 50 mmEN 12163 minimum (R420).
Hardness75 HRBminTypical 82 HRBUp to 25 mmRWMA Class 2 minimum. Typical value for 12.7 mm TH04 rod.
Hardness70 HRBminOver 25 to 50 mmRWMA Class 2 minimum.
Hardness65 HRBminOver 50 mmRWMA Class 2 minimum.

Physical Properties

PropertyTH04 Solution Treated, Cold Worked & Precipitation Hardened | EN 12163
Densityat 20°C8.89 g/cm³
Modulus of Elasticityat 20°C117 GPa
Shear Modulusat 20°C49.6 GPa
Thermal Conductivityat 20°C324 W/m·K
Coefficient of Thermal Expansionat 20–100°C17.6 µm/m·°C
Specific Heat Capacityat 20°C385 J/kg·K
Electrical Conductivityat 20°C80 % IACS
Electrical Resistivityat 20°C0.02 µΩ·m
Melting Point / Rangeat Solidus–Liquidus1070 °C

Service Conditions

Service Temperature

Max 200 °C

Notes

Continuous load-bearing limit about 200°C. Above the 425–500°C ageing range the chromium precipitates coarsen and hardness and strength fall progressively — this softening resistance is what distinguishes CuCr1 from pure copper, but it is time- and temperature-dependent. Resistance welding electrode faces reach higher temperatures only transiently and are water cooled. For higher softening resistance, consider C18150 (CuCr1Zr). As an FCC copper alloy it has no ductile-to-brittle transition; low-temperature use is not restricted.

Corrosion Performance

General corrosion

Good atmospheric and fresh-water corrosion resistance; forms a stable oxide film. Attacked by ammonia, oxidising acids (nitric), and sulphur-bearing atmospheres at temperature. Keep electrode cooling water clean and deionised where specified to avoid internal scaling and erosion. Sour service: copper alloys are not certified to NACE MR0175 — not applicable to this grade.

Pitting resistance

Behaves like high-conductivity copper: good resistance in fresh and cooling water as used in water-cooled electrodes, with low pitting risk in clean circuits. Not designed for seawater immersion — for seawater duty select a nickel aluminium bronze.

Additional notes

Not applicable — PREN applies to stainless steels and nickel alloys.

Heat Treatment

HEAT TREATMENT GUIDE — C18200 / CuCr1 / 2.1291

Solution treatment: 980–1000°C (mill practice up to about 1030°C) — short soak, typically 15–30 min, to dissolve chromium — rapid water quench — soft, supersaturated solid solution, low conductivity. Cold working: draw or roll after quenching — increases final strength and accelerates ageing (TH04 route). Precipitation hardening (ageing): 425–500°C — 2–4 h (typically about 460°C for 3 h) — air cool — fine chromium precipitates; restores conductivity to about 80% IACS and reaches TH04 / R470 properties. Hot working: 816–927°C (1500–1700°F); hot forgeability good. Over-ageing / softening: exposure above the ageing range (brazing, welding, overheating in service) coarsens precipitates and softens the alloy — properties are recovered only by a new solution treatment, quench and age. No heat treatment is needed after machining TH04 stock.

ENGINEERING NOTES
Weldability
Fair

C18200 can be joined by gas-shielded arc welding (GTAW / GMAW), soldering and brazing; oxy-fuel welding, coated-electrode welding and resistance spot or seam welding of the alloy itself are not recommended. Any joining operation that heats the metal above the 425–500°C ageing range over-ages or re-solutionises the chromium precipitates, so the heat-affected zone loses the hardness and conductivity of the TH04 temper and cannot be fully restored without a new solution treatment and age. Copper's high thermal conductivity calls for preheat on thicker sections when arc welding; use a chloride/fluoride flux when brazing because the chromium oxide film resists wetting. Where full properties are required, machine the part from TH04 bar and avoid welding near working faces.

Filler metals
  • ERCu · AWS A5.7 / TIG (GTAW)Deoxidised copper filler for joining to copper — weld and HAZ will be softer than TH04 parent
  • ERCu · AWS A5.7 / MIG (GMAW)For thicker sections; preheat required because of copper's heat conductivity
  • BAg series · AWS A5.8 / BrazingSilver brazing alloys with flux for electrode shanks and holders; brazing softens the joint zone
Machinability
Fair

Machinability rating 20 (free-cutting brass C36000 = 100). Machine in the TH04 condition as supplied — no heat treatment is needed afterwards. The alloy is tough and produces long, stringy chips: use sharp, polished carbide or HSS tools with high positive rake, chip-breaker geometry, generous coolant and moderate speeds. Avoid rubbing cuts, which work harden the surface and degrade electrode face finish.

Applications

  • Resistance spot welding electrode caps, tips and shanks for automotive body-in-white lines
  • Seam welding wheels and projection welding dies for tank, drum and duct fabrication
  • Electrode holders, adaptors and current-carrying arms for resistance welding guns
  • Flash and butt welding dies and clamping jaws in steel fabrication plants
  • Switchgear contacts, arcing parts and circuit breaker components for power distribution
  • High-current busbar links, terminals and cable connectors for GCC substation equipment
  • Back-up bars and chill blocks for arc welding of steel and aluminium
  • Mould cores, inserts and hot runner components needing rapid heat extraction
  • Water-cooled induction heating coils and fixtures in heat treatment shops
  • Current-carrying shafts and slip-ring components in rotating electrical machinery
  • Welding fixtures and platens for resistance welding cells in UAE manufacturing

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

C18200 chromium copper is used mainly for resistance welding electrodes — spot welding caps and tips, seam welding wheels, electrode holders and current-carrying arms — because it keeps its hardness at electrode temperatures while conducting about 80% IACS. It is also used for switchgear contacts, circuit breaker parts, busbar links, cable connectors, back-up bars and mould cores that need fast heat extraction. In the UAE and GCC, typical buyers are automotive and fabrication plants, switchgear manufacturers and welding equipment suppliers.

Get in touch

Elevateyourprojectswithoursuperiorsteel