Copper Alloys dealers in UAE

C17200 / CuBe2 / 2.1247 Beryllium Copper | Supplier in UAE & GCC

C17200 (CuBe2) — beryllium copper, the strongest copper alloy: 1,140–1,550 MPa and HRC 36–45 when aged, ~22% IACS; non-sparking and non-magnetic.

Industries Served

Oil & Gas
Aerospace & Defence
Petrochemical
Automotive
Manufacturing
Mould & Die
Power Generation

Overview

C17200 beryllium copper (CuBe2, EN CW101C, DIN 2.1247, UNS C17200, Alloy 25, BS CB101) is the highest-strength copper alloy, supplied to ASTM B196 for rod and bar, ASTM B194 for plate and EN 12163, and to AMS 4533 (TF00 bar), AMS 4534 (TH04 bar) and MIL-C-21657 for aerospace and defence procurement. It contains 1.80–2.00% beryllium with at least 0.20% nickel plus cobalt, which refines the grain and controls the precipitation reaction. Solution annealed at about 760–800°C and quenched, the alloy is soft and formable; ageing at 316–357°C for 2–3 hours precipitates coherent beryllium-rich phases that raise tensile strength from 410–590 MPa (TB00) to 1140 MPa minimum (TF00) and up to 1280 MPa minimum in cold-drawn TH04 bar, with hardness of HRC 36–45. Aged material keeps about 22% IACS conductivity, is non-sparking and non-magnetic (relative permeability about 1.003), and has outstanding fatigue and wear resistance — the reason C17200 is chosen for springs, connectors, bearings, non-sparking tools and downhole oilfield parts.

Nifty Alloys supplies C17200 / CuBe2 beryllium copper from Dubai, UAE, in round bar, flat bar and plate / block, in the mill-hardened TF00 and TH04 tempers and in the TB00 and TD04 tempers for customer age hardening, to ASTM B196 and ASTM B194, with AMS 4533, AMS 4534 and MIL-C-21657 supply available on request. Stock material is cut to length or block size and dispatched with EN 10204 3.1 Mill Test Certificates as standard, giving certified, traceable chemistry and mechanical results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list, temper and drawing to request a quote — quotations are turned around the same day.

Chemical Composition

Cu

Copper

1.9 %
Be

Beryllium

1.8 – 2 %

Ni + Co

Nickel + Cobalt

≥ 0.2 %

Ni + Co + Fe

≤ 0.6 %

Al

Aluminium

≤ 0.2 %

Si

Silicon

≤ 0.2 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM B196 / B196M

ASTM

Revision: B196 / B196M — current edition

Standard specification for copper-beryllium alloy rod and bar. Covers C17200 in AT (solution annealed) and HT (precipitation hardened) temper conditions.

Primary ASTM standard for C17200 round bar and rod. Note: ASTM B196 covers BOTH C18200/C18150 (copper chromium) AND C17200 (beryllium copper) - check the alloy designation carefully when referencing this standard.

Available Forms

Flat Bar

6–75 mm. Thickness; width × thickness to order. [VERIFY — stock range not confirmed]

Plate / Block

6–100 mm. Thickness, ASTM B194; blocks saw-cut to size. [VERIFY — stock range not confirmed]

Round Bar

6–200 mm. Diameter. TH04 to 76.2 mm (AMS 4534 limit); TF00 / TB00 in larger sections. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
TF00 Precipitation Hardened (AT) — primary stocked condition. TH04, TD04 and TB00 per current stock list or on request. AMS 4533 / AMS 4534 / MIL-C-21657 certification on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

ASTM B196 / B196M

Designations & Equivalents

StandardDesignationNotes
UNSC17200Primary designation — Unified Numbering System
Common NameCDA 172 / Alloy 25(CDA) Copper Development Association number and common alloy name
DINCuBe2German / European chemical designation
EN / Werkstoff2.1247German material number
EN NameCuBe2EN 12163 chemical designation
EN / WerkstoffCW101C(EN Number) EN numerical designation
BSCB101British Standard (BS 2870 / 2871 / 2874)
ASTMB196 / B196MRod and bar — TB00, TD04, TF00, TH04
ASTMB194Plate, sheet, strip and rolled bar
Common NameEN 12163(EN Standard) Rod for general purposes
AMSAMS 4533Bars and rods, solution and precipitation heat treated (TF00 / AT)
AMSAMS 4534Bars and rods, solution treated, cold worked and precipitation heat treated (TH04 / HT), up to 76.2 mm
AMSAMS 4650 [VERIFY — Ashwin to confirm]Companion bar specification for the solution heat treated (TB00) temper — aliases only
AMSAMS 4651 [VERIFY — Ashwin to confirm]Companion bar specification for the cold drawn (TD04) temper — aliases only
Common NameMIL-C-21657(MIL) Military specification — rod, bar, strip and plate
Common NameQQ-C-530(Federal (cancelled)) Cancelled federal specification — legacy drawings only; supply now to ASTM B196
Common NameRWMA Class 4 (Group A)(RWMA) Resistance-welding electrode classification — AWS J1.3
Common NameBeryllium copper / BeCu / CuBe / copper beryllium / beryllium bronze / Alloy 25Buyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and mechanical results to ASTM B196 (bar) or ASTM B194 (plate).
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
AMS 4533ConditionalSupplied on request for TF00 bar and rod — confirm specification revision at enquiry.
AMS 4534ConditionalSupplied on request for TH04 bar and rod up to 76.2 mm — confirm specification revision at enquiry.
MIL-C-21657Requires ConfirmationSupplied against MIL-C-21657 call-outs on request — confirm specification revision and status at enquiry.

Specifications

Mechanical Properties

Values per ASTM B196 / B196M. Bar length compares conditions within each row.

PropertyTF00 Precipitation Hardened (AT) | ASTM B196TB00 Solution Annealed (A) | ASTM B196TD04 Solution Annealed + Cold Worked, Hard (H) | ASTM B196TH04 Hard + Precipitation Hardened (HT) | ASTM B196
Tensile Strength (UTS)1140–1380 MPaRoom temp — all sizesASTM B196. Upper value for design guidance only.410–590 MPaRoom temp — all sizesASTM B196 Table 2.620–900 MPaRoom temp — up to 10 mmASTM B196 Table 2.1280–1550 MPaRoom temp — up to 9.5 mmASTM B196. Upper value for design guidance only.
Tensile Strength (UTS)––620–860 MPaRoom temp — over 10 to 25 mmASTM B196 Table 2.1240–1520 MPaRoom temp — over 9.5 to 25.4 mmASTM B196.
Tensile Strength (UTS)––590–830 MPaRoom temp — over 25 to 75 mmASTM B196 Table 2.1210–1480 MPaRoom temp — over 25.4 to 76.2 mmASTM B196.
Yield Strength (0.2% Proof Stress)1000 MPaminRoom temp — up to 76.2 mmASTM B196 minimum.140 MPaminRoom temp — all sizesASTM B196 minimum.520 MPaminRoom temp — all sizes to 75 mmASTM B196 minimum.1100 MPaminUp to 9.5 mmASTM B196 minimum.
Yield Strength (0.2% Proof Stress)900 MPaminRoom temp — over 76.2 mmASTM B196 minimum.––1070 MPaminOver 9.5 to 25.4 mmASTM B196 minimum.
Yield Strength (0.2% Proof Stress)–––1000 MPaminOver 25.4 to 76.2 mmASTM B196 minimum.
Elongation4 %min4D gauge — up to 76.2 mmASTM B196 minimum.20 %min4D gaugeASTM B196 minimum.8 %min4D gaugeASTM B196 minimum.2 %min4D gauge — up to 25.4 mmASTM B196 minimum.
Elongation3 %min4D gauge — over 76.2 mmASTM B196 minimum.––4 %min4D gauge — over 25.4 to 76.2 mmASTM B196 minimum.
Hardness36–42 HRCTypical 39 HRCRod and bar over 10 mmASTM B196 range. Hardness is the standard acceptance test over 10 mm.45–85 HRBRod and bar over 10 mmASTM B196 range.88–102 HRBOver 10 to 25 mmASTM B196; HRB 88–103 up to 10 mm, HRB 88–101 over 25 mm.38–44 HRCOver 9.5 to 25.4 mmASTM B196 range; HRC 39–45 up to 9.5 mm, HRC 37–44 over 25.4 mm.

Physical Properties

PropertyTF00 Precipitation Hardened (AT) | ASTM B196TB00 Solution Annealed (A) | ASTM B196TD04 Solution Annealed + Cold Worked, Hard (H) | ASTM B196TH04 Hard + Precipitation Hardened (HT) | ASTM B196
Densityat 20°C8.36 g/cm³8.36 g/cm³8.36 g/cm³8.36 g/cm³
Modulus of Elasticityat 20°C131 GPa131 GPa131 GPa131 GPa
Thermal Conductivityat 20°C115 W/m·K115 W/m·K115 W/m·K115 W/m·K
Coefficient of Thermal Expansionat 20–200°C17 µm/m·°C17 µm/m·°C17 µm/m·°C17 µm/m·°C
Electrical Conductivityat 20°C22 % IACS22 % IACS22 % IACS22 % IACS
Relative Magnetic Permeabilityat 20°C1 -1 -1 -1 -
Melting Point / Rangeat Solidus–Liquidus870 °C870 °C870 °C870 °C

Service Conditions

Service Temperature

Max 200 °C

Notes

[VERIFY — maxServiceTempC 200: continuous load-bearing limit for aged C17200 not confirmed in a producer or code source] Aged C17200 retains strength well at moderate temperature, but stress relaxation in springs and contacts increases above about 150°C, and prolonged exposure approaching the 316–357°C ageing range over-ages the alloy and reduces hardness. Do not expose aged parts to temperatures above the ageing range in service or processing. As an FCC copper alloy it has no ductile-to-brittle transition and retains toughness at cryogenic temperatures.

Corrosion Performance

General corrosion

Good resistance to seawater, fresh water, many industrial atmospheres, hydrocarbons and non-oxidising acids. Susceptible to stress corrosion cracking in moist ammonia and attacked by oxidising acids (nitric) and wet sulphur compounds. Galvanically similar to other copper alloys. Sour service: copper alloys are not certified to NACE MR0175 — not applicable to this grade.

Pitting resistance

Good resistance to pitting and crevice corrosion in seawater and chloride environments, comparable to other high-copper alloys, and resistant to chloride stress corrosion cracking. Aged and annealed tempers behave similarly.

Additional notes

Not applicable — PREN applies to stainless steels and nickel alloys.

Heat Treatment

HEAT TREATMENT GUIDE — C17200 / CuBe2 / 2.1247

Solution annealing: about 760–800°C — soak sufficient to dissolve beryllium (time per section) — rapid water quench — TB00 (A) condition, soft and formable, HRB 45–85. Cold working: draw or roll after solution annealing — TD04 (H) condition, HRB 88–103; increases final aged strength. Precipitation hardening (standard): 316–357°C (600–675°F) — 3 h for TB00, 2 h for TD04 up to 19.1 mm, 3 h for TD04 over 19.1 mm — air cool — TB00 → TF00 (AT) properties; TD04 → TH04 (HT) properties. Special ageing: other times and temperatures may be used for higher ductility, conductivity or spring stability; ASTM B196 Table 3 limits then do not apply. Dimensional change: ageing causes a small, uniform shrinkage [VERIFY — magnitude not confirmed] — allow for it on precision parts machined before ageing. Over-ageing: exposure above the ageing range softens the alloy; recover by re-solution annealing and re-ageing. Mill-hardened TF00 / TH04 need no heat treatment after machining. ⚠︎ SAFETY: heat treatment of clean solid parts in air is not a dust hazard, but oxide scale removed by grinding or pickling sludge contains beryllium — handle per the supplier SDS.

ENGINEERING NOTES
Weldability
Fair

C17200 can be joined by GTAW, GMAW, electron-beam and resistance welding, and by brazing and soldering. Join in the TB00 or TD04 condition and age afterwards wherever possible: welding or brazing hardened TF00 / TH04 material over-ages or re-solutionises the heat-affected zone, which loses strength and hardness unless the part is solution annealed and re-aged. Clean the surface of beryllium oxide before brazing and use an active flux. No preheat is normally needed for thin sections; preheat thicker sections because of copper's thermal conductivity. ⚠︎ Welding and brazing generate fume that can contain beryllium — use local exhaust ventilation and respiratory protection as specified in the supplier SDS.

Filler metals
  • C17200 wire (ASTM B197) · Matching alloy / TIG (GTAW)Matching beryllium copper filler — weld in TB00 / TD04 and age the assembly afterwards
  • C17200 wire (ASTM B197) · Matching alloy / MIG (GMAW)For thicker sections; preheat and local fume extraction required
  • BAg series · AWS A5.8 / BrazingSilver brazing with active flux; brazing temperature solution-treats the joint zone — re-age where strength is required
Machinability
Fair

Machinability rating about 20 (free-cutting brass C36000 = 100). TB00 and TD04 machine most easily but are gummy; aged TF00 / TH04 (HRC 36–45) machines cleanly with carbide tooling, rigid set-ups and positive rake. Aged parts need no further heat treatment; parts machined in TB00 / TD04 are aged afterwards and shrink slightly, so leave finishing allowance on precision dimensions. ⚠︎ Use flood coolant to capture swarf and mist, collect fines wet, and use extraction for grinding, polishing and EDM — dry processes can release respirable beryllium-containing particles.

Applications

  • Non-sparking hand tools — wrenches, hammers, chisels — for oil, gas and petrochemical plants
  • MWD / LWD drill-string components and downhole tool housings for GCC oilfields
  • Aircraft landing-gear bushings and bearings needing high load capacity and wear resistance
  • Precision springs, diaphragms and Belleville washers that resist fatigue and stress relaxation
  • Electrical connector contacts, relay springs and switch parts carrying current under load
  • Plastic injection mould inserts, cores and hot runner nozzles for rapid heat extraction
  • Projection and flash welding dies and seam-welding inserts (RWMA Class 4)
  • Valve seats, valve guides and pump wear rings in corrosive service
  • Non-magnetic instrument housings and fasteners near sensitive navigation equipment
  • High-strength bolts, retaining rings and roll pins where steel is unsuitable
  • Bearing cages and heavy-duty bushings in mining and offshore machinery

Related grades in Copper Alloys

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

C17200 beryllium copper is used where a copper alloy must reach steel-like strength: non-sparking tools for oil, gas and petrochemical plants, MWD and downhole tool components, aircraft landing-gear bushings and bearings, precision springs, connector contacts, plastic mould inserts and projection welding dies. Aged C17200 reaches 1140–1550 MPa tensile strength with HRC 36–45 hardness while staying non-magnetic and about 22% IACS conductive. In the UAE and GCC, oilfield service companies and hazardous-area maintenance teams are major users.

Get in touch

Elevateyourprojectswithoursuperiorsteel