Stainless Steel dealers in UAE

321 / 1.4541 / X6CrNiTi18-10 Stainless Steel | Supplier in UAE & GCC

321 / 1.4541 / X6CrNiTi18-10 — titanium-stabilised austenitic stainless: resists intergranular corrosion at 427–816°C; exhausts, heat exchangers, aerospace.

Industries Served

Petrochemical
Oil & Gas
Aerospace & Defence
Power Generation
Food Processing

Overview

321 stainless steel (UNS S32100, EN 1.4541 / X6CrNiTi18-10, ASTM A276 / A479 / A240, AMS 5645 / AMS 5510) is a titanium-stabilised austenitic chromium-nickel stainless steel containing 17.0–19.0% chromium, 9.0–12.0% nickel and titanium of at least five times the carbon (plus nitrogen) content, up to 0.70%. Titanium combines preferentially with carbon to form stable titanium carbides, preventing chromium carbide precipitation at the grain boundaries — so 321 resists intergranular corrosion after welding or exposure in the 427–816°C sensitisation range, where unstabilised 304 would be attacked. It also has better creep and stress-rupture strength than 304 / 304L and oxidation resistance to about 850–870°C in continuous service. In the solution-annealed condition it gives 515 MPa minimum tensile and 205 MPa minimum yield strength with 40% elongation (ASTM A479 / A240), or 500–700 MPa and 190 MPa to EN 10088-3. General corrosion resistance is similar to 304, and 321 is non-magnetic when annealed and tough down to cryogenic temperatures. Typical uses are aircraft exhausts and manifolds, expansion bellows, heat exchangers, furnace parts, refinery and petrochemical equipment and high-temperature welded fabrications.

Nifty Alloys supplies 321 / 1.4541 stainless steel from Dubai, UAE, in round bar, plate and sheet, solution annealed, with 321H and AMS 5645 / AMS 5510 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry and mechanical properties; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.04 %
C

Carbon

≤ 0.08 %

0.5 %
Si

Silicon

≤ 1 %

1.5 %
Mn

Manganese

≤ 2 %

P

Phosphorus

≤ 0.045 %

S

Sulfur

≤ 0.03 %

17.8 %
Cr

Chromium

17 – 19 %

10 %
Ni

Nickel

9 – 12 %

0.4 %
Ti

Titanium

5 – 0.7 %

N

Nitrogen

≤ 0.1 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM A479 / A479M

ASTM

Revision: ASTM A479 / A479M — current edition

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels — covers 316 / 316L in the annealed condition and Type 316 / 316L in strain-hardened Level 1 (S1) and Level 2 (S2) conditions.

ASME equivalent: SA-479 (ASME BPVC Section II Part A). General requirements per ASTM A484. Strain-hardened bar is marked S1 or S2 after the grade designation.

Available Forms

Plate / Block

3–80 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

4–300 mm. Diameter, solution annealed. [VERIFY — stock range not confirmed]

Sheet

0.5–3 mm. Thickness; 2B finish, standard sheet sizes. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Solution Annealed — standard. 321H and AMS 5645 / 5510 certified material on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM A479 / A479M

Designations & Equivalents

StandardDesignationNotes
AISI / SAE321ASTM A276 / A479 / A240 Type 321
UNSS32100Unified Numbering System
UNSS32109 (321H)High-carbon variant for elevated-temperature strength — on request
EN / Werkstoff1.4541EN 10088 material number
EN NameX6CrNiTi18-10EN 10088 steel name
AMSAMS 5645Bars, wire, forgings, tubing, rings (Module 2)
AMSAMS 5510Sheet, strip, plate (Module 2)
Common NameMIL-S-6721 / QQ-S-766(MIL / Federal) Legacy military / federal specifications — aliases only [VERIFY]
BS321S31 / 321S51 / EN58BFormer British designations
JISSUS321Japanese Industrial Standard
Common NameZ6CNT18-10(AFNOR) French designation
Common Name06Cr18Ni11Ti / 0Cr18Ni10Ti(GB) Chinese designation
Common Name321 stainless / Ti-stabilised stainless / SS321 / high-temperature stainlessBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and mechanical properties.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156SuitableAustenitic stainless steel in the solution-annealed condition, 22 HRC max, acceptable under ISO 15156-3 within the environmental limits of the applicable table (chloride, temperature, H2S partial pressure, pH, no elemental sulphur) [VERIFY — current edition].
NACE MR0103SuitableRefinery sour service — solution annealed, hardness limits per MR0103.
AMS 5645 / AMS 5510ConditionalSupplied to AMS 5645 (bar) or AMS 5510 (sheet / plate) on request — confirm revision.
ASME Section II / VIIISuitableSA-240 / SA-479 / SA-276 material for pressure equipment.

Specifications

Mechanical Properties

Values per ASTM A479 / A479M. Bar length compares conditions within each row.

PropertySolution Annealed | ASTM A479
Tensile Strength (UTS)515 MPaminASTM A479 / A276 / A240, annealedSpecified minimum.
Yield Strength (0.2% Proof Stress)205 MPaminASTM A479 / A276 / A240Specified minimum.
Elongation40 %min50 mm gaugeSpecified minimum (A479: 30% for some sizes).
Hardness217 HBmaxASTM A240 plate / sheetSpecified maximum (95 HRB).
Impact Energy (Charpy V-notch)100 JminEN 10088-3 +AT, room temp, longitudinalEN minimum.

Physical Properties

PropertySolution Annealed | ASTM A479
Densityat 20°C7.9 g/cm³
Modulus of Elasticityat 20°C200 GPa
Thermal Conductivityat 20°C15 W/m·K
Coefficient of Thermal Expansionat 20–100°C16 µm/m·°C
Electrical Resistivityat 20°C0.73 µΩ·m

Service Conditions

Service Temperature

Min -196 °CMax 870 °C

Notes

Oxidation resistance to about 850°C (EN data) – 870°C in continuous dry-air service. Resists intergranular corrosion after exposure in the 427–816°C sensitisation range. For creep-loaded service above about 500°C, 321H (higher carbon) is preferred. Retains toughness to cryogenic temperatures (−196°C).

Corrosion Performance

PREN 18

General corrosion

General corrosion resistance similar to 304, with slightly lower resistance in strong nitric acid. Main advantage: resistance to intergranular corrosion and polythionic-acid stress corrosion after high-temperature exposure. Susceptible to chloride stress corrosion cracking like other austenitic grades.

Pitting resistance

Pitting resistance similar to 304 — not for seawater or high-chloride service; use 316 / duplex grades there.

PREN notes

PREN ≈ 17–19 (no Mo) — similar to 304.

Heat Treatment

HEAT TREATMENT GUIDE — 321 / 1.4541 / X6CrNiTi18-10

Supply condition: solution annealed at about 1020–1120°C, rapid air or water cooling — fully austenitic. Not hardenable by heat treatment — strength increased only by cold work. Hot forming: 1150–850°C, followed by solution annealing. Stabilising anneal (optional): about 870–900°C for 2–4 h, air cool — maximises titanium carbide formation for best intergranular-corrosion resistance in severe service. Stress relief: about 870–900°C (stabilised) is safe for 321 without sensitisation risk. Welding: no preheat or PWHT required.

ENGINEERING NOTES
Weldability
Excellent

Readily welded by all common processes (GTAW, GMAW, SMAW, SAW) without preheat or post-weld heat treatment. Use ER347 / E347 (niobium-stabilised) fillers — titanium does not transfer reliably across the arc. Welds retain resistance to intergranular corrosion in the as-welded condition.

Filler metals
  • ER347 · AWS A5.9 / TIG (GTAW) / MIG (GMAW)Standard filler — Nb-stabilised; titanium does not transfer reliably
  • E347-16 · AWS A5.4 / SMAWCovered electrode for 321
  • ER321 · AWS A5.9 / TIG / MIGMatching filler for GTAW where specified
  • ER309L · AWS A5.9 / TIG / MIGDissimilar welds to carbon or low-alloy steel
Machinability
Fair

Machinability about 45% of B1112, similar to 304. Work hardens rapidly — use rigid set-ups, sharp positive-rake tools, steady feed and generous coolant; avoid dwelling or light cuts that glaze the surface.

Applications

  • Aircraft exhaust stacks, manifolds and ring collectors (AMS 5510 / 5645)
  • Expansion bellows and flexible joints
  • Heat exchangers, boiler and superheater components
  • Refinery and petrochemical equipment — polythionic-acid service
  • Furnace parts, thermal oxidisers and heat-treatment fixtures
  • Automotive and generator-set exhaust systems
  • High-temperature welded fabrications where post-weld annealing is impractical
  • Chemical process vessels and piping in GCC plants
  • Food-processing equipment and storage
  • Cryogenic and low-temperature equipment

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

321 is used for high-temperature and welded service where intergranular corrosion is a risk: aircraft exhausts and manifolds, expansion bellows, heat exchangers, furnace parts, thermal oxidisers, refinery and petrochemical equipment and high-temperature welded fabrications. In the UAE and GCC it is common in refinery, power and process-plant equipment.

Get in touch

Elevateyourprojectswithoursuperiorsteel