Stainless Steel dealers in UAE

310 / 310S / 1.4845 Heat Resistant Stainless Steel | Supplier in UAE & GCC

310 / 310S / 1.4845 — 25Cr-20Ni heat resistant austenitic stainless: oxidation resistance to about 1100°C; furnace parts, burners, heat exchangers and kilns.

Industries Served

Petrochemical
Power Generation
Heavy Engineering
Oil & Gas
Aerospace & Defence

Overview

310 and 310S stainless steel (UNS S31000 / S31008, EN 1.4845 / X8CrNi25-21, ASTM A276 / A479 / A240, AMS 5651 / AMS 5521) are high-chromium, high-nickel austenitic heat-resisting steels containing 24.0–26.0% chromium and 19.0–22.0% nickel. The high chromium forms a dense, adherent oxide scale and the high nickel stabilises the austenite, giving oxidation resistance in air to about 1100°C in continuous service, good resistance in cyclic conditions and moderately carburising atmospheres, and useful creep strength. 310S is the low-carbon version (0.08% maximum carbon) that improves weldability and resistance to sensitisation; 310 (0.25% maximum) is used where slightly higher high-temperature strength is wanted, and 310H (0.04–0.10%) is specified for creep-loaded pressure parts. In the solution-annealed condition 310S gives 515 MPa minimum tensile and 205 MPa minimum yield strength (ASTM A479 / A240), or 500–700 MPa and 210 MPa to EN 10095. Long exposure at about 600–900°C can form brittle sigma phase, and resistance to sulphur-bearing reducing atmospheres is limited. Typical uses are furnace parts, burners, radiant tubes, heat-treatment fixtures, kiln components, heat exchangers and boiler internals.

Nifty Alloys supplies 310 / 310S / 1.4845 stainless steel from Dubai, UAE, in round bar, plate and sheet, solution annealed, with 310H and AMS 5651 / AMS 5521 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry and mechanical properties; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.05 %
C

Carbon

≤ 0.08 %

0.6 %
Si

Silicon

≤ 1.5 %

1.3 %
Mn

Manganese

≤ 2 %

P

Phosphorus

≤ 0.045 %

S

Sulfur

≤ 0.03 %

25 %
Cr

Chromium

24 – 26 %

20.5 %
Ni

Nickel

19 – 22 %

N

Nitrogen

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM A479 / A479M

ASTM

Revision: ASTM A479 / A479M — current edition

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels — covers 316 / 316L in the annealed condition and Type 316 / 316L in strain-hardened Level 1 (S1) and Level 2 (S2) conditions.

ASME equivalent: SA-479 (ASME BPVC Section II Part A). General requirements per ASTM A484. Strain-hardened bar is marked S1 or S2 after the grade designation.

Available Forms

Plate / Block

3–60 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

6–300 mm. Diameter, solution annealed. [VERIFY — stock range not confirmed]

Sheet

0.5–3 mm. Thickness; 2B finish. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Solution Annealed 310S — standard. 310, 310H and AMS 5651 / 5521 certified material on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM A479 / A479M

Designations & Equivalents

StandardDesignationNotes
AISI / SAE310SLow-carbon grade — primary chemistry (UNS S31008)
AISI / SAE310Standard carbon (UNS S31000, C ≤ 0.25) — on request
UNSS31008 / S31000 / S31009310S / 310 / 310H
EN / Werkstoff1.4845EN 10095 material number
EN NameX8CrNi25-21EN 10095 steel name
AMSAMS 5651Bars, wire, forgings, tubing, rings (Module 2)
AMSAMS 5521Sheet, strip, plate (Module 2)
Common NameQQ-S-763(Federal) Legacy federal specification — aliases only [VERIFY]
BS310S16 / 310S31Former British designations
JISSUS310SJapanese Industrial Standard
Common NameZ8CN25-20 / Z12CN25-20(AFNOR) French designations
Common Name06Cr25Ni20 / 0Cr25Ni20(GB) Chinese designation
Common Name310S stainless / 25-20 stainless / heat resistant stainless / furnace steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and mechanical properties.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156SuitableAustenitic stainless steel in the solution-annealed condition, 22 HRC max, acceptable under ISO 15156-3 within the environmental limits of the applicable table [VERIFY — current edition].
AMS 5651 / AMS 5521ConditionalSupplied to AMS 5651 (bar) or AMS 5521 (sheet / plate) on request — confirm revision.
ASME Section II / VIIISuitableSA-240 / SA-479 / SA-276 material for pressure equipment.

Specifications

Mechanical Properties

Values per ASTM A479 / A479M. Bar length compares conditions within each row.

PropertySolution Annealed | ASTM A479
Tensile Strength (UTS)515 MPaminASTM A479 / A276 / A240, annealedSpecified minimum.
Tensile Strength (UTS)500–700 MPaEN 10095 +A, bar ≤ 160 mmEN range; Rp0.2 210 MPa min.
Yield Strength (0.2% Proof Stress)205 MPaminASTM A479 / A276 / A240Specified minimum.
Elongation30 %minASTM A479, 50 mm gaugeSpecified minimum (A276 / A240: 40%).
Hardness217 HBmaxASTM A240 plate / sheetSpecified maximum (95 HRB).

Physical Properties

PropertySolution Annealed | ASTM A479
Densityat 20°C7.9 g/cm³
Modulus of Elasticityat 20°C196 GPa
Thermal Conductivityat 20°C14 W/m·K
Coefficient of Thermal Expansionat 20–100°C15.5 µm/m·°C
Specific Heat Capacityat 20°C500 J/kg·K
Electrical Resistivityat 20°C0.85 µΩ·m

Service Conditions

Service Temperature

Min -196 °CMax 1100 °C

Notes

Oxidation resistance in air to about 1100°C continuous (about 1040°C intermittent). Limited resistance to sulphur-bearing reducing gases. Long exposure at about 600–900°C forms sigma phase, reducing room-temperature toughness. Not suggested for severe thermal shock of repeated liquid quenching. Tough at cryogenic temperatures.

Corrosion Performance

PREN 25

General corrosion

Good aqueous corrosion resistance thanks to high Cr and Ni — used in some concentrated nitric acid service. Excellent oxidation and good carburisation resistance; limited sulphidation resistance in reducing atmospheres.

Pitting resistance

Moderate aqueous pitting resistance; not intended for seawater or chloride service. Remains susceptible to chloride stress corrosion cracking.

PREN notes

PREN ≈ 24–26 (no Mo) — high Cr, but primarily a heat-resisting grade.

Heat Treatment

HEAT TREATMENT GUIDE — 310 / 310S / 1.4845

Supply condition: solution annealed at about 1050–1150°C, rapid air or water cooling — fully austenitic. Not hardenable by heat treatment — strength increased only by cold work. Hot forming: about 1150–950°C, followed by solution annealing. Sigma recovery: material embrittled by long service at 600–900°C can be restored by re-solution annealing at about 1100–1150°C. Welding: no preheat or PWHT required.

ENGINEERING NOTES
Weldability
Good

Readily welded by GTAW, GMAW, SMAW and SAW without preheat or PWHT. Use matching ER310 / E310 filler. The fully austenitic weld is more prone to hot cracking than 304 — keep heat input and interpass temperature low and minimise restraint. Avoid service or post-weld exposure in the 600–900°C sigma range where toughness matters.

Filler metals
  • ER310 · AWS A5.9 / TIG (GTAW) / MIG (GMAW)Matching filler for 310 / 310S
  • E310-16 · AWS A5.4 / SMAWMatching covered electrode
  • ENiCrFe-3 · AWS A5.11 / SMAWNickel-alloy electrode for dissimilar joints and high-temperature service
Machinability
Fair

Machinability similar to or slightly below 304. Work hardens rapidly — use rigid set-ups, sharp positive-rake tools, steady feed and generous coolant.

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

310 and 310S are used for high-temperature service in air and combustion gases: furnace parts, burners, radiant tubes, heat-treatment fixtures, kiln and cement-plant hardware, heat exchangers, boiler internals and refinery heater components. In the UAE and GCC they are common in refinery, power, cement and heat-treatment plants.

Get in touch

Elevateyourprojectswithoursuperiorsteel