Stainless Steel dealers in UAE

416 / 1.4005 / X12CrS13 Free-Machining Stainless Steel | Supplier in UAE & GCC

416 / 1.4005 / X12CrS13 — free-machining 13% Cr martensitic stainless: highest machinability of any stainless, hardenable to 248–302 HB; shafts, screws.

Industries Served

Manufacturing
Automotive
Oil & Gas
Aerospace & Defence

Overview

416 stainless steel (UNS S41600, EN 1.4005 / X12CrS13, ASTM A582, AMS 5610) is a free-machining, hardenable 13% chromium martensitic stainless steel — essentially 410 with a controlled sulphur addition of 0.15–0.35%. The sulphur forms manganese sulphide inclusions that break chips and lubricate the cutting edge, giving 416 the highest machinability of any stainless steel, about 85% of a free-machining carbon steel, which makes it the standard choice for high-volume automatic screw-machine parts. It is supplied annealed (220 HB maximum to EN 10088-3; 262 HB maximum to ASTM A582 Condition A) or hardened and tempered — ASTM A582 Condition T (248–302 HB) and Condition H (293–352 HB), or EN 10088-3 +QT650 (650–850 MPa). The trade-off for machinability is lower corrosion resistance, weldability and toughness than 410: 416 performs well in fresh water, steam, mild atmospheres and mild chemicals, with best results in the hardened and polished condition, but it is unsuitable for marine, chloride or sour service. Typical uses are pump and motor shafts, valve parts, fasteners, gears, axles and precision machined components.

Nifty Alloys supplies 416 / 1.4005 free-machining stainless steel from Dubai, UAE, in round bar and hexagonal bar, annealed or hardened and tempered to Condition T, with Condition H and AMS 5610 material on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, condition and hardness results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and condition to request a quote — quotations are turned around the same day.

Chemical Composition

0.11 %
C

Carbon

0.06 – 0.15 %

0.4 %
Si

Silicon

≤ 1 %

0.9 %
Mn

Manganese

≤ 1.5 %

P

Phosphorus

≤ 0.04 %

0.25 %
S

Sulfur

0.15 – 0.35 %

13 %
Cr

Chromium

12 – 14 %

Mo

Molybdenum

≤ 0.6 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10088-3

EN

Revision: EN 10088-3:2014

Stainless steels — Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products. European standard covering 1.4542 (X5CrNiCuNb16-4).

EN designation: 1.4542, X5CrNiCuNb16-4. Supplied in solution annealed (+AT) condition.

Available Forms

Hexagonal Bar

6–80 mm. Across flats, cold drawn. [VERIFY — stock range not confirmed]

Round Bar

3–250 mm. Diameter, annealed or Condition T; centreless ground on request. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A) and Condition T [VERIFY — stocked conditions]; Condition H and AMS 5610 on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 10088-3

Designations & Equivalents

StandardDesignationNotes
AISI / SAE416ASTM A582 Type 416
UNSS41600Unified Numbering System
EN / Werkstoff1.4005EN 10088 material number
EN NameX12CrS13EN 10088 steel name
AMSAMS 5610Free-machining bar, wire, forgings (Module 2)
BS416S21 / EN56AMFormer British designations (BS 970, withdrawn) — aliases only
JISSUS416Japanese Industrial Standard
Common NameZ11CF13 / Z12CF13(AFNOR) French designations
Common NameY1Cr13(GB) Chinese designation
Common Name416 stainless / free-cutting stainless / free-machining 13% chrome / 416 HTBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — Not used for sour service — free-machining, high-sulphur grade. For NACE valve trim, specify 410 in the QDT condition (22 HRC max).
AMS 5610ConditionalSupplied to AMS 5610 on request — confirm type and revision.

Specifications

Mechanical Properties

Values per EN 10088-3. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN 10088-3Condition T | ASTM A582
Hardness220 HBmaxAnnealed (+A)EN 10088-3 maximum (ASTM A582 Condition A: 262 HB max).248–302 HBASTM A582 Condition TSpecified range.
Hardness–293–352 HBASTM A582 Condition H (on request)Specified range.
Tensile Strength (UTS)730 MPamaxTypical 517 MPaAnnealedEN 10088-3 maximum; typical 517 MPa.758 MPatypicalCondition TTypical — not specified.
Yield Strength (0.2% Proof Stress)276 MPatypicalAnnealedTypical — not specified.586 MPatypicalCondition TTypical — not specified.
Elongation30 %typicalAnnealedTypical — not specified.18 %typicalCondition TTypical — not specified.

Physical Properties

PropertyAnnealed (+A) | EN 10088-3Condition T | ASTM A582
Densityat 20°C7.7 g/cm³7.7 g/cm³
Modulus of Elasticityat 20°C200 GPa200 GPa
Thermal Conductivityat 20°C25 W/m·K25 W/m·K
Coefficient of Thermal Expansionat 20–100°C10 µm/m·°C10 µm/m·°C
Electrical Resistivityat 20°C0.57 µΩ·m0.57 µΩ·m

Service Conditions

Service Temperature

Max 650 °C

Notes

Oxidation resistance in continuous service to about 650°C. Hardened material should not be used above its tempering temperature; avoid tempering at about 400–550°C. Toughness, especially transverse, is lower than 410 because of sulphide stringers — not recommended for shock or sub-zero loading.

Corrosion Performance

PREN 13

General corrosion

Resists fresh water, steam, dry air, mild acids and alkalis. Best corrosion resistance in the hardened and polished condition; passivate after machining. In the humid, coastal UAE climate, use only for sheltered or lubricated service.

Pitting resistance

Poor pitting resistance — sulphide inclusions act as initiation sites. Unsuitable for marine, chloride or seawater exposure.

PREN notes

PREN ≈ 12–14 (no Mo / N); effective resistance lower than 410 because of sulphide inclusions.

Heat Treatment

HEAT TREATMENT GUIDE — 416 / 1.4005 / X12CrS13

Hot forming: 1100–800°C, air cool. Soft annealing: about 745–825°C, slow furnace cooling — 220 HB max (EN 10088-3); ASTM A582 Condition A 262 HB max. Hardening: 950–1050°C, quench in oil or air. Tempering: Condition T (248–302 HB) and +QT650 (650–850 MPa) — about 600–700°C; Condition H (293–352 HB) — lower tempering. Avoid tempering at about 400–550°C (reduced toughness and corrosion resistance). Post-weld / repair anneal: about 790°C (1450°F). Passivation after machining recommended to remove embedded iron and exposed sulphides.

ENGINEERING NOTES
Weldability
Poor

Not recommended for welding — the sulphur addition causes hot cracking and porosity, and the weld zone hardens. If unavoidable, preheat to about 200–300°C, use low-hydrogen practice with ER410 or austenitic ER309L / ER312 filler, and anneal at about 790°C (1450°F) after welding to restore ductility and corrosion resistance. For welded parts, specify 410 instead.

Filler metals
  • ER410 · AWS A5.9 / TIG / MIGMatching martensitic filler — preheat and post-weld anneal required
  • ER309L · AWS A5.9 / TIG / MIGAustenitic filler for tougher, non-hardenable joints
  • E312-16 · AWS A5.4 / SMAWAustenitic electrode tolerant of sulphur dilution — repairs only
Machinability
Excellent

Highest machinability of any stainless steel — about 85% of B1112 free-machining carbon steel — in the annealed condition. Condition T bar also machines well with carbide tooling. Manganese sulphide inclusions break chips and extend tool life; suited to automatic screw machines and CNC turning centres.

Applications

  • Automatic screw-machine parts and high-volume turned components
  • Pump shafts, motor shafts and armature shafts
  • Valve stems, bodies and trim for water and steam (non-sour) service
  • Bolts, nuts, screws and studs
  • Gears, pinions and axles
  • Hex-bar fittings, adaptors and nozzles
  • Firearm and precision mechanism components
  • Carburettor, fuel-system and automotive parts
  • Aerospace hardware to AMS 5610
  • Precision components for GCC machine shops

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

416 stainless steel is used for parts that need a lot of machining: automatic screw-machine components, pump and motor shafts, valve parts for water and steam, bolts, nuts and screws, gears, axles, hex fittings and precision mechanisms. In the UAE and GCC it is popular with machine shops for high-volume turned parts in mild service.

Get in touch

Elevateyourprojectswithoursuperiorsteel