Stainless Steel dealers in UAE

410 / 1.4006 / X12Cr13 Martensitic Stainless Steel | Supplier in UAE & GCC

410 / 1.4006 / X12Cr13 — 12% Cr hardenable martensitic stainless: annealed or Q&T 650–850 MPa, NACE QDT on request; valves, pump shafts, fasteners.

Industries Served

Oil & Gas
Power Generation
Petrochemical
Manufacturing
Aerospace & Defence

Overview

410 stainless steel (UNS S41000, EN 1.4006 / X12Cr13, ASTM A276 / A479 / A240, AMS 5613) is the basic general-purpose hardenable martensitic stainless steel, containing 0.08–0.15% carbon and 11.5–13.5% chromium. Its chromium content is just sufficient for passivity, giving good resistance to atmospheric corrosion, fresh water, steam and mild chemicals, while carbon allows it to be hardened by quenching and tempering to properties comparable to low-alloy engineering steels. Supplied soft annealed (220 HB maximum to EN 10088-3) for machining and forming, it is hardened from 950–1000°C in oil or air and tempered: the EN 10088-3 +QT650 condition gives 650–850 MPa tensile strength, 450 MPa minimum proof stress, 15% elongation and 25 J impact energy, and tempering at lower temperatures gives higher strength and hardness. In the quenched and double-tempered (QDT) condition at 22 HRC maximum, 410 is acceptable for sour service under NACE MR0175 / ISO 15156-3 and is widely used for valve trim and wellhead components. It resists scaling to about 650°C in continuous service. Typical uses are valve stems and trim, pump shafts, steam and gas turbine blades, fasteners, cutlery and petrochemical equipment.

Nifty Alloys supplies 410 / 1.4006 stainless steel from Dubai, UAE, in round bar, flat bar and plate, annealed or quenched and tempered, with QDT material for NACE service and AMS 5613 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, condition, tensile and hardness results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and condition to request a quote — quotations are turned around the same day.

Chemical Composition

0.12 %
C

Carbon

0.08 – 0.15 %

0.4 %
Si

Silicon

≤ 1 %

0.6 %
Mn

Manganese

≤ 1.5 %

P

Phosphorus

≤ 0.04 %

S

Sulfur

≤ 0.03 %

12.5 %
Cr

Chromium

11.5 – 13.5 %

Ni

Nickel

≤ 0.75 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10088-3

EN

Revision: EN 10088-3:2014

Stainless steels — Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products. European standard covering 1.4542 (X5CrNiCuNb16-4).

EN designation: 1.4542, X5CrNiCuNb16-4. Supplied in solution annealed (+AT) condition.

Available Forms

Flat Bar

5–100 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Plate / Block

3–80 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

6–400 mm. Diameter, annealed or Q&T. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A) — standard; Q&T (+QT650), NACE QDT (22 HRC max) and AMS 5613 on request [VERIFY — stocked conditions].
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 10088-3

Designations & Equivalents

StandardDesignationNotes
AISI / SAE410 / SAE 51410ASTM A276 / A479 / A240 Type 410
UNSS41000Unified Numbering System
EN / Werkstoff1.4006EN 10088 material number
EN NameX12Cr13EN 10088 steel name
AMSAMS 5613Bars, wire, forgings — annealed (Module 2)
AMSAMS 5504Sheet, strip and plate — aliases only
BS410S21 / EN56AFormer British designations
JISSUS410Japanese Industrial Standard
Common NameZ10C13(AFNOR) French designation
Common Name1Cr13 / 12Cr13(GB) Chinese designation
Common Name410 stainless / 12% chrome stainless / martensitic stainless / 410 QDTBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition, tensile and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156SuitableIn the quenched and double-tempered (QDT) condition only — austenitise, quench, temper at ≥ 621°C, cool, and second temper at ≥ 621°C (below the first) — with 22 HRC maximum, per ISO 15156-3 [VERIFY — current table]. Annealed and standard Q&T conditions are not NACE-certified as supplied; QDT on request.
AMS 5613ConditionalSupplied to AMS 5613 on request — confirm revision.

Specifications

Mechanical Properties

Values per EN 10088-3. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN 10088-3Hardened & Tempered (+QT650) | EN 10088-3
Hardness220 HBmaxAnnealed (+A)EN 10088-3 maximum.22 HRCmaxNACE QDT conditionISO 15156-3 maximum — QDT supply only.
Tensile Strength (UTS)730 MPamaxAnnealed (+A)EN 10088-3 maximum.650–850 MPa+QT650, ≤ 160 mmEN 10088-3 range.
Tensile Strength (UTS)450 MPaminASTM A479 annealedASTM minimum [VERIFY].–
Yield Strength (0.2% Proof Stress)205 MPaminASTM A479 annealedASTM minimum [VERIFY].450 MPamin+QT650EN 10088-3 minimum.
Elongation20 %minASTM A479 annealedASTM minimum.15 %min+QT650EN 10088-3 minimum.
Impact Energy (Charpy V-notch)–25 Jmin+QT650, room tempEN 10088-3 minimum.

Physical Properties

PropertyAnnealed (+A) | EN 10088-3Hardened & Tempered (+QT650) | EN 10088-3
Densityat 20°C7.7 g/cm³7.7 g/cm³
Modulus of Elasticityat 20°C215 GPa215 GPa
Thermal Conductivityat 20°C30 W/m·K30 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.5 µm/m·°C10.5 µm/m·°C
Electrical Resistivityat 20°C0.6 µΩ·m0.6 µΩ·m

Service Conditions

Service Temperature

Max 650 °C

Notes

Good scaling resistance to about 650°C in continuous service (about 815°C intermittent). For load-bearing use, mechanical properties are typically quoted to about 400°C; hardened material should not be used above its tempering temperature, and tempering at about 400–550°C should be avoided (embrittlement). Toughness at sub-zero temperatures is limited — specify impact testing where required.

Corrosion Performance

PREN 13

General corrosion

Best corrosion resistance in the hardened and tempered condition with a polished surface. Resists mild acids, alkalis, food and many petroleum products. In the humid, coastal UAE climate, keep surfaces clean and protected.

Pitting resistance

Limited pitting resistance — suitable for atmospheric, fresh water, steam and mild chemical service; not for seawater or chloride-rich media.

PREN notes

PREN ≈ 12–14 (no Mo / N).

Heat Treatment

HEAT TREATMENT GUIDE — 410 / 1.4006 / X12Cr13

Hot forming: 1100–800°C, air cool. Soft annealing: about 745–825°C, slow cooling — 220 HB max (+A). Hardening: 950–1000°C, quench in oil or air. Tempering: +QT650 — 680–780°C, air cool (Rm 650–850 MPa). Lower tempering (about 200–370°C) gives maximum strength (about 38–45 HRC). Avoid tempering at about 400–550°C — reduced impact strength and corrosion resistance. NACE QDT: harden, temper at ≥ 621°C, cool to room temperature, then second temper at ≥ 621°C (below the first temper) — 22 HRC max. Stress relieving: about 650–760°C after heavy machining or welding.

ENGINEERING NOTES
Weldability
Fair

Weldable with precautions — the weld zone hardens on cooling. Preheat to about 150–260°C, use low-hydrogen practice and post-weld temper / anneal at about 650–760°C to restore toughness. Matching ER410 / E410 fillers give hardenable welds; ER410NiMo gives better toughness; austenitic ER309L is used for tougher, non-hardenable joints. NACE-service welds must be re-tempered to meet 22 HRC max.

Filler metals
  • ER410 · AWS A5.9 / TIG / MIGMatching filler — hardenable weld; preheat and PWHT required
  • E410-15 / E410-16 · AWS A5.4 / SMAWMatching covered electrode
  • ER410NiMo · AWS A5.9 / TIG / MIGNi-Mo modified filler — improved weld toughness
  • ER309L · AWS A5.9 / TIG / MIGAustenitic filler for tougher, non-hardenable joints and dissimilar welds
Machinability
Fair

Machines best in the annealed or intermediate-tempered condition with carbide or HSS tooling at moderate speeds. Q&T material up to about 300 HB machines well with carbide. For high-volume machining, 416 / 1.4005 is the free-machining alternative.

Applications

  • Valve stems, seats, gates and trim — including NACE QDT trim for GCC oil and gas
  • Wellhead and API 6A components in the QDT condition
  • Pump shafts, impellers and wear rings
  • Steam and gas turbine blades and buckets
  • Bolts, nuts, screws and other fasteners
  • Petrochemical and refinery trays, liners and fittings
  • Cutlery, scissors and kitchen utensils
  • Mining and machinery parts in mildly corrosive service
  • Burner and furnace components to about 650°C
  • Aerospace hardware to AMS 5613

Related grades in Stainless Steel

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

410 stainless steel is used for valve stems and trim, wellhead components, pump shafts, steam and gas turbine blades, fasteners, petrochemical equipment, cutlery and machinery parts. Hardened and tempered it offers strength comparable to low-alloy steels with moderate corrosion resistance. In the UAE and GCC it is widely used for oil and gas valve trim in the NACE QDT condition.

Get in touch

Elevateyourprojectswithoursuperiorsteel