Stainless Steel dealers in UAE

420 / X30Cr13 / 1.4028 Martensitic Stainless Steel | Supplier in UAE & GCC

420 / X30Cr13 / 1.4028 — 13% Cr hardenable martensitic stainless, with 1.4021 and 1.4034: shafts, valve trim, pump parts, cutting tools and moulds.

Industries Served

Oil & Gas
Manufacturing
Food Processing
Mould & Die
Automotive

Overview

420 stainless steel (UNS S42000, ASTM A276 / A240 Type 420) is a hardenable 13% chromium martensitic stainless steel. In Europe it is supplied to EN 10088 in three carbon levels, all covered on this page: 1.4021 / X20Cr13 (0.16–0.25% C), the standard 1.4028 / X30Cr13 (0.26–0.35% C) and 1.4034 / X46Cr13 (0.43–0.50% C), each with about 12–14% chromium. Higher carbon gives higher attainable hardness and wear resistance at some cost to toughness and corrosion resistance: hardened and tempered, 1.4021 reaches 700–950 MPa (+QT700 / +QT800), 1.4028 reaches 850–1000 MPa (+QT850) and about 50 HRC when hardened, and 1.4034 reaches about 52–56 HRC. The grades are supplied soft annealed (230–245 HB maximum) for machining and are hardened by oil or air quenching from about 950–1050°C and tempering. Corrosion resistance is best in the hardened and polished condition and is suited to fresh water, steam, mild atmospheres and food acids — lower than the austenitic grades. ASTM Type 420 only requires 0.15% carbon minimum, so the EN variant governs the properties; the "420A / 420B / 420C" labels are trade shorthand.

Nifty Alloys supplies 420 stainless steel — 1.4028, 1.4021 and 1.4034 — from Dubai, UAE, in round bar, flat bar and plate, soft annealed for machining and hardening. Our team can help you select the right carbon level: 1.4021 for tougher shafts and valve parts, 1.4028 for general hardened components, and 1.4034 for cutting tools and wear parts. Every supply carries an EN 10204 3.1 Mill Test Certificate stating the EN variant, chemistry and annealed hardness; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and grade to request a quote — quotations are turned around the same day.

Chemical Composition

0.3 %
C

Carbon

0.26 – 0.35 %

0.4 %
Si

Silicon

≤ 1 %

0.5 %
Mn

Manganese

≤ 1.5 %

P

Phosphorus

≤ 0.04 %

S

Sulfur

≤ 0.03 %

13 %
Cr

Chromium

12 – 14 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10088-3

EN

Revision: EN 10088-3:2014

Stainless steels — Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products. European standard covering 1.4542 (X5CrNiCuNb16-4).

EN designation: 1.4542, X5CrNiCuNb16-4. Supplied in solution annealed (+AT) condition.

Available Forms

Flat Bar

5–100 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Plate / Block

3–80 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

6–300 mm. Diameter, annealed. [VERIFY — stock range per variant not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A) — 1.4028 standard; 1.4021 and 1.4034 [VERIFY — stocked variants]; hardened & tempered on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 10088-3

Designations & Equivalents

StandardDesignationNotes
AISI / SAE420ASTM A276 / A240 Type 420 — C 0.15 min, covers all three EN variants
UNSS42000Unified Numbering System
EN / Werkstoff1.4028X30Cr13 — primary chemistry (SpecSheet 1)
EN / Werkstoff1.4021X20Cr13 — lower-carbon variant (SpecSheet 2)
EN / Werkstoff1.4034X46Cr13 — higher-carbon variant (SpecSheet 3)
Common Name420A / 420B / 420CIndustry shorthand only — usage varies between suppliers; not ASTM designations
BS420S37 / 420S45Former British designations (1.4021 / 1.4028)
JISSUS420J1 / SUS420J2Japanese (1.4021 / 1.4028)
Common Name2Cr13 / 3Cr13 / 4Cr13(GB) Chinese (1.4021 / 1.4028 / 1.4034)
Common Name20Kh13 / 30Kh13 / 40Kh13(GOST) Russian equivalents
Common NameZ20C13 / Z33C13 / Z44C14(AFNOR) French equivalents
Common Name420 stainless / 13% chrome stainless / martensitic stainless / cutlery steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — states the EN variant supplied, chemistry and annealed hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Requires ConfirmationISO 15156-3 accepts UNS S42000 only in a specified quench-and-double-temper condition at 22 HRC max [VERIFY — current ISO 15156-3 table]. Annealed and standard hardened conditions are not NACE-acceptable as supplied.

Specifications

Mechanical Properties

Values per EN 10088-3. Bar length compares conditions within each row.

Property1.4028 Annealed | EN 10088-31.4021 Annealed | EN 10088-31.4034 Annealed | EN 10088-3
Hardness245 HBmaxAnnealed (+A)EN 10088-3 maximum.230 HBmaxAnnealed (+A)EN 10088-3 maximum.245 HBmaxAnnealed (+A)EN 10088-3 maximum.
Hardness50 HRCtypicalHardened, low-temperature temperedTypical — guidance.–52–56 HRCHardened 980–1030°C, low-temperature temperedTypical — guidance.
Tensile Strength (UTS)800 MPamaxAnnealed (+A)EN 10088-3 maximum.760 MPamaxAnnealed (+A)EN 10088-3 maximum.800 MPamaxAnnealed (+A)EN 10088-3 maximum.
Tensile Strength (UTS)850–1000 MPaH&T +QT850, ≤ 160 mmEN 10088-3 — noted per register.700–850 MPaH&T +QT700, ≤ 160 mmEN 10088-3; Rp0.2 500 MPa min, A 13%, KV 25 J.–
Tensile Strength (UTS)–800–950 MPaH&T +QT800, ≤ 160 mmEN 10088-3; Rp0.2 600 MPa min, A 12%, KV 20 J.–
Yield Strength (0.2% Proof Stress)650 MPaminH&T +QT850EN 10088-3 minimum.––
Elongation10 %minH&T +QT850EN 10088-3 minimum.––
Impact Energy (Charpy V-notch)–25 JminH&T +QT700, room tempEN 10088-3 minimum.–

Physical Properties

Property1.4028 Annealed | EN 10088-31.4021 Annealed | EN 10088-31.4034 Annealed | EN 10088-3
Densityat 20°C7.7 g/cm³7.7 g/cm³7.7 g/cm³
Modulus of Elasticityat 20°C215 GPa215 GPa215 GPa
Thermal Conductivityat 20°C30 W/m·K30 W/m·K30 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.5 µm/m·°C10.5 µm/m·°C10.5 µm/m·°C
Electrical Resistivityat 20°C0.65 µΩ·m0.65 µΩ·m0.65 µΩ·m

Service Conditions

Service Temperature

Max 400 °C

Notes

Hardened material should not be used above its tempering temperature; avoid prolonged exposure at about 400–550°C (temper embrittlement). Scaling resistance to about 650°C in intermittent service. Toughness is limited at sub-zero temperatures, especially for 1.4034.

Corrosion Performance

PREN 13

General corrosion

Corrosion resistance is best in the hardened and tempered condition with a ground or polished surface; it is reduced in the annealed state and as carbon rises. Tempering at about 400–550°C lowers corrosion resistance. In the humid, coastal UAE climate, keep surfaces clean and polished.

Pitting resistance

Limited pitting resistance — suited to fresh water, steam, mild atmospheres, food acids and mild organic media; not for seawater or chloride-rich service.

PREN notes

PREN ≈ 12–14 (no Mo / N) — the lowest of the stainless families.

Heat Treatment

HEAT TREATMENT GUIDE — 420 / X30Cr13 / 1.4028 (1.4021 / 1.4028 / 1.4034)

Hot forming: 1100–800°C, slow cooling. Soft annealing: about 745–825°C, slow furnace cooling — 1.4021 230 HB max; 1.4028 and 1.4034 245 HB max. Hardening: 950–1050°C, quench in oil or air (1.4021 950–1050°C; 1.4028 950–1050°C; 1.4034 980–1030°C). Tempering: 1.4021 +QT700 about 650–750°C, +QT800 about 600–700°C; 1.4028 +QT850 about 625–675°C; low-temperature tempering (about 100–200°C) for maximum hardness — about 50 HRC (1.4028) and 52–56 HRC (1.4034). Avoid tempering at about 400–550°C (embrittlement and reduced corrosion resistance). Stress relieving: about 650–700°C after heavy machining.

ENGINEERING NOTES
Weldability
Poor

Weldability falls as carbon rises: 1.4021 is fair, 1.4028 limited, 1.4034 not recommended. Where welding is needed, preheat to about 200–300°C, use low-hydrogen practice and temper / post-weld anneal at about 650–750°C immediately after welding to restore toughness. Matching 410 / 420 fillers give hardenable welds; austenitic fillers (309L / 312) give tougher, non-hardenable joints.

Filler metals
  • ER420 · AWS A5.9 / TIG / MIGMatching filler — hardenable weld; preheat and PWHT required
  • E410-15 / E410-16 · AWS A5.4 / SMAWMatching-type electrode for 13% Cr martensitic steels
  • ER309L · AWS A5.9 / TIG / MIGAustenitic filler for tougher, non-hardenable joints and dissimilar welds
  • E312-16 · AWS A5.4 / SMAWAustenitic electrode for repair of higher-carbon variants
Machinability
Fair

Machine in the annealed condition (230–245 HB max) with carbide or HSS tooling at moderate speeds; higher-carbon 1.4034 is harder on tools. For free-machining requirements, 416 / 1.4005 is the sulphurised alternative. Finish-grind and polish after hardening for best corrosion resistance.

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

420 stainless steel is used for hardened parts that need moderate corrosion resistance: pump shafts and plungers, valve stems and trim, cutlery and industrial blades, surgical and measuring instruments, plastic moulds, fasteners, springs and wear parts. In the UAE and GCC it is common in pump, valve, food-processing and workshop applications.

Get in touch

Elevateyourprojectswithoursuperiorsteel