Stainless Steel dealers in UAE

431 / 1.4057 / X17CrNi16-2 Martensitic Stainless Steel | Supplier in UAE & GCC

431 / 1.4057 / X17CrNi16-2 — Ni-bearing 16% Cr martensitic stainless, Condition T 850–1000 MPa; best corrosion resistance of martensitics; shafts, bolts.

Industries Served

Marine
Oil & Gas
Aerospace & Defence
Food Processing
Manufacturing

Overview

431 stainless steel (UNS S43100, EN 1.4057 / X17CrNi16-2, BS 431S29 / EN57, AMS 5628) is a high-chromium, nickel-bearing martensitic stainless steel containing 0.12–0.22% carbon, 15.0–17.0% chromium and 1.5–2.5% nickel. The higher chromium gives it the best corrosion resistance of the hardenable martensitic grades, while nickel balances the structure so it can be fully hardened and improves toughness. It is normally supplied hardened and tempered to Condition T — 850–1000 MPa tensile strength, about 635 MPa minimum proof stress, 11% elongation and 248–302 HB — which combines high tensile and torsional strength with good impact toughness, making it a standard material for shafts. The EN 10088-3 equivalents are +QT800 (800–950 MPa) and +QT900 (900–1050 MPa). Because 431 hardens even on slow cooling, it cannot be fully annealed; softened material is sub-critically annealed to 295 HB maximum. Corrosion resistance approaches that of 304 in many environments and is best in the hardened and polished condition. Typical uses are marine propeller and pump shafts, valve spindles, high-strength bolts and fasteners, aircraft fittings and food-processing machinery.

Nifty Alloys supplies 431 / 1.4057 stainless steel from stock in Dubai, UAE, in round bar, hardened and tempered to Condition T as standard, with annealed material and AMS 5628 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry, condition, tensile, impact and hardness results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.17 %
C

Carbon

0.12 – 0.22 %

0.3 %
Si

Silicon

≤ 1 %

0.5 %
Mn

Manganese

≤ 1.5 %

P

Phosphorus

≤ 0.04 %

S

Sulfur

≤ 0.03 %

16 %
Cr

Chromium

15 – 17 %

2 %
Ni

Nickel

1.5 – 2.5 %

Mo / Cu / N
Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

BS 970-1 (withdrawn)

Other

Revision: BS 970-1 (withdrawn — legacy specification)

Available Forms

Round Bar

6–300 mm. Diameter, Condition T; peeled / ground. Condition T properties subject to ruling section. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Condition T (850–1000 MPa) — standard stocked condition. Annealed and AMS 5628 on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

BS 970-1 (withdrawn)

Designations & Equivalents

StandardDesignationNotes
AISI / SAE431 / SAE 51431ASTM A276 Type 431
UNSS43100Unified Numbering System
EN / Werkstoff1.4057EN 10088 material number
EN NameX17CrNi16-2EN 10088 steel name
BS431S29 / 431S29T / EN57BS 970 designations (withdrawn); T = Condition T
AMSAMS 5628431 modified — on request, specific melt (Module 2)
Common NameBS S80(BS Aerospace) UK aerospace 431 — aliases only
JISSUS431Japanese Industrial Standard
Common NameZ15CN16-02(AFNOR) French designation
Common Name1Cr17Ni2 / 14Cr17Ni2(GB) Chinese designation
Common Name431 stainless / 431S29T / EN57 / propeller shaft steel / pump shaft steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition, tensile, impact and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — UNS S43100 is not among the ISO 15156-3 pre-qualified martensitic grades [VERIFY]. For sour service, specify 410 QDT (22 HRC max) or 17-4PH H1150D.
AMS 5628ConditionalSupplied to AMS 5628 on request from a specific melt — confirm revision.

Specifications

Mechanical Properties

Values per BS 970-1 (withdrawn). Bar length compares conditions within each row.

PropertyCondition T | BS 970-1Annealed (+A) | EN 10088-3
Tensile Strength (UTS)850–1000 MPaCondition TBS 970 431S29 range.950 MPamaxAnnealed (+A)EN 10088-3 maximum.
Yield Strength (0.2% Proof Stress)635 MPaminCondition TPublished minimum (some sources 665–680 MPa).–
Elongation11 %minA (5.65√So)Published minimum.–
Impact Energy (Charpy V-notch)34 JminRoom tempPublished value.–
Hardness248–302 HBCondition TBS 970 range.295 HBmaxAnnealed (+A)EN 10088-3 maximum.

Physical Properties

PropertyCondition T | BS 970-1Annealed (+A) | EN 10088-3
Densityat 20°C7.7 g/cm³7.7 g/cm³
Modulus of Elasticityat 20°C200 GPa200 GPa
Thermal Conductivityat 20°C25 W/m·K25 W/m·K
Coefficient of Thermal Expansionat 20–100°C10 µm/m·°C10 µm/m·°C
Electrical Resistivityat 20°C0.7 µΩ·m0.7 µΩ·m

Service Conditions

Service Temperature

Min -40 °CMax 400 °C

Notes

Commonly specified for about -40°C to 400°C in the hardened and tempered condition. Avoid tempering or prolonged service at about 400–550°C (embrittlement and reduced corrosion resistance). Good impact toughness for a martensitic stainless; specify impact testing for sub-zero duty.

Corrosion Performance

PREN 16

General corrosion

Best corrosion resistance of the martensitic stainless steels, approaching 304 in many environments; good resistance to organic acids, mild mineral acids and atmospheres. Optimum in the hardened, tempered and polished condition; passivate after machining.

Pitting resistance

Moderate pitting resistance — better than 410 / 420; suitable for splash-zone marine shafting and many waters, but not for stagnant seawater crevices without protection.

PREN notes

PREN ≈ 15–17 (no Mo / N) — highest of the standard martensitic grades.

Heat Treatment

HEAT TREATMENT GUIDE — 431 / 1.4057 / X17CrNi16-2

Forging: heat slowly to about 850°C, then to 1150–1200°C; finish above about 900°C; cool slowly (furnace or ash). Soft (sub-critical) annealing: 680–800°C, slow cooling — 295 HB max (+A). Full annealing is not possible — 431 hardens even on slow cooling; double sub-critical annealing can help. Hardening: 950–1050°C, quench in oil or air. Tempering: Condition T (850–1000 MPa) — about 600–650°C, 1 h minimum, air cool. EN +QT800 — temper 750–800°C then 650–700°C; +QT900 — temper 600–650°C. Avoid tempering at about 400–550°C. Stress relieving: below the tempering temperature after heavy machining.

ENGINEERING NOTES
Weldability
Poor

Weldable only with care — the weld zone hardens and is crack-prone. Preheat to about 200–300°C, use low-hydrogen practice and temper at about 600–650°C immediately after welding. Matching 410-type or austenitic ER309L / ER312 fillers are used depending on whether a hardenable joint is needed. Avoid welding Condition T shafts in highly stressed areas.

Filler metals
  • ER410NiMo · AWS A5.9 / TIG / MIGNi-Mo martensitic filler — hardenable, tougher weld; preheat and PWHT required
  • ER309L · AWS A5.9 / TIG / MIGAustenitic filler for tougher, non-hardenable joints and dissimilar welds
  • E312-16 · AWS A5.4 / SMAWAustenitic electrode for repairs
Machinability
Fair

Condition T (248–302 HB) machines well with carbide tooling and is commonly finish-machined in this condition. Annealed material (295 HB max) is not much softer because 431 cannot be fully annealed. Passivate finished parts for best corrosion resistance.

Applications

  • Marine propeller shafts and stern-gear components for GCC vessels
  • Pump shafts, impellers and seawater-cooled pump parts
  • Valve spindles, stems and trim (non-sour service)
  • High-strength bolts, studs, nuts and fasteners
  • Aircraft fittings and structural parts (AMS 5628 / BS S80)
  • Food-processing and paper-machinery shafts and spindles
  • Piston rods and hydraulic components
  • Mixer and agitator shafts
  • Beater bars and wear parts in mildly corrosive service
  • General engineering shafts needing strength and corrosion resistance

Related grades in Stainless Steel

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

431 stainless steel is used for parts that need high strength with good corrosion resistance: marine propeller and pump shafts, valve spindles, high-strength bolts and fasteners, piston rods, aircraft fittings and food-processing and paper-machinery shafts. In the UAE and GCC it is a standard material for marine shafting and pump shafts.

Get in touch

Elevateyourprojectswithoursuperiorsteel