Tool Steel dealers in UAE

1.1730 / C45U / C45W Carbon Tool Steel | Supplier in UAE & GCC

1.1730 (C45U) — unalloyed 0.45% C tool steel with excellent machinability for mould bases, clamping plates and fixtures; surface hardenable.

Industries Served

Mould & Die
Manufacturing
Automotive
Heavy Engineering

Overview

1.1730 carbon tool steel (DIN 1.1730 / C45U, formerly C45W to DIN 17350) is an unalloyed medium-carbon tool steel containing 0.42–0.50% carbon, 0.15–0.40% silicon and 0.60–0.80% manganese, specified to EN ISO 4957. It is produced to tool-steel quality, with tighter analysis and inspection than the engineering grade C45E / 1.1191, and is supplied unhardened for easy, fast machining. That makes it the standard European material for mould bases, top and bottom clamping plates, die sets, holders and fixtures, where flatness, stability and low cost matter more than hardness. Where wear surfaces are needed, 1.1730 can be water hardened from 800–850 °C to about 58 HRC at the surface, or flame or induction hardened locally to give a hard surface over a tough core. Its unalloyed analysis gives shallow hardening, so it is not used for cavities, cutting edges or heavily loaded tooling.

Nifty Alloys supplies 1.1730 / C45U carbon tool steel through our Dubai, UAE facility in flat bar and plate / block, saw-cut to size for mould bases and fixtures. 1.1730 is supplied on request against your order, and P20 / 1.2311 pre-hardened mould steel is held in Dubai stock for cavity plates and inserts. Every order carries an EN 10204 3.1 Mill Test Certificate as standard, confirming chemistry and hardness with full traceability to the producing mill. EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE and the GCC — Saudi Arabia, Kuwait, Qatar, Oman and Bahrain — and export to Europe, India and Africa. As an ISO 9001:2015 certified tool steel supplier in the UAE, our team can help you specify the right plate for your mould set. Contact our team to request a quote.

Chemical Composition

0.45 %
C

Carbon

0.42 – 0.5 %

0.3 %
Si

Silicon

0.15 – 0.4 %

0.7 %
Mn

Manganese

0.6 – 0.8 %

P

Phosphorus

≤ 0.03 %

S

Sulfur

≤ 0.03 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 4957

EN

Revision: EN ISO 4957:2018

Tool steels — specification for chemical composition, heat treatment, and properties of tool steels including cold work, hot work, and high-speed grades.

Published as BS EN ISO 4957; leading BS dropped to match house style. European standard governing 1.2379 (X153CrMoV12) and other DIN tool steel grades. Supersedes former DIN 17350 for tool steels. Referenced in European and Middle Eastern engineering procurement. Equivalent German standard: DIN EN ISO 4957.

Available Forms

Flat Bar

10–200 mm. Thickness. Widths to order. Supplied on request — confirm size and lead time at enquiry. [VERIFY with sales]

Plate / Block

10–400 mm. Thickness. Saw-cut or milled to mould-base dimensions. Supplied on request. [VERIFY with sales]

Stock & delivery

Stock location
Dubai, UAE
In stock
As-Rolled / Normalised — 1.1730 is supplied on request (not held as Dubai stock); soft annealed also available on request. Lead time confirmed at quotation. P20 / 1.2311 pre-hardened is held in Dubai stock for cavity plates.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 4957

Designations & Equivalents

StandardDesignationNotes
EN / Werkstoff1.1730European material number — primary designation. Not 1.1191 (C45E, EN 10083-2 engineering steel) or 1.0503 (C45).
DINC45UCurrent DIN / EN designation
DINC45WFormer DIN 17350 name — still used on older drawings
EN NameC45UEN ISO 4957 steel name
ISOC45UISO 4957 designation
AISI / SAENoneNo AISI tool steel equivalent. AISI W1 is not equivalent (W1 is a 0.70%+ C water-hardening steel). Nearest carbon-steel analysis is AISI 1045 — see Common Name.
AMSNoneNo AMS specification applies to 1.1730 — not an aerospace procurement grade
Common NameCarbon tool steel, mould base steel, C45 tool steel, 1730 steel, 1045 (nearest carbon-steel analysis only)Buyer search terms used in UAE / GCC and Europe

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableMill Test Certificate provided as standard. Confirms chemistry and hardness to EN ISO 4957.
EN 10204 3.2ConditionalAvailable on request — specify at order stage. Additional lead time and cost may apply.

Specifications

Mechanical Properties

Values per EN ISO 4957. Bar length compares conditions within each row.

PropertyAs-Rolled / Normalised | EN ISO 4957
Hardness (as supplied)–Surface, as-rolled / normalised[VERIFY — source not confirmed]. Enter from first mill certificate. Soft annealed alternative: max 207 HB (producer data).
Tensile Strength (UTS)–Room tempNot specified by EN ISO 4957 — leave blank.
Yield Strength (0.2% Proof Stress)–Room tempNot specified — leave blank.
Elongation–Not specified — leave blank.
Hardness (surface, water hardened)58 HRCtypical800–840 °C, water quench, 20 mm sectionTypical — producer data. Not a specified value.

Physical Properties

PropertyAs-Rolled / Normalised | EN ISO 4957
Densityat 20°C–[VERIFY — source not confirmed]. Leave blank until confirmed.
Modulus of Elasticityat 20°C–[VERIFY — source not confirmed]. Leave blank until confirmed.
Thermal Conductivityat 20°C44.9 W/m·K
Coefficient of Thermal Expansionat 20–100°C12.5 µm/m·°C
Specific Heat Capacityat 20°C–[VERIFY — source not confirmed]. Leave blank until confirmed.
Melting Point / Rangeat Solidus–[VERIFY — source not confirmed]. Leave blank until confirmed.

Service Conditions

Service Temperature

Max 200 °C

Notes

Practical continuous limit for mould-base, clamping-plate and fixture duty, which covers normal thermoplastic moulding temperatures. Surface-hardened parts must stay below their tempering temperature or they soften. 1.1730 has no alloy content for hot strength — use H13 / 1.2344 for die-casting cavities and hot tooling.

Corrosion Performance

General corrosion

No corrosion resistance. 1.1730 rusts quickly in humid UAE and GCC workshops. Oil or coat machined mould plates before storage; consider nickel plating or black oxide for mould bases in humid areas. For corrosion-resistant mould steel specify 1.2083 / X40Cr14.

Pitting resistance

No pitting resistance.

Additional notes

Not applicable — unalloyed carbon tool steel.

Heat Treatment

ProcessTemperatureCoolingResult & notes
HEAT TREATMENT GUIDE1.1730 / C45U / C45W: As-Rolled / Normalised (supply condition): No further treatment needed for mould bases and fixtures. Normalising temperature for re-normalising [VERIFYsource not confirmed]. Soft Annealing: 680–710 °Cabout 4 h — slow furnace cooling to about 500 °C, then air — max 207 HB. Stress Relieving: 600–650 °C — slow furnace cooling. After heavy rough machining or welding, before finish machining. Hardening: Austenitise at 800–850 °C — quench in water. Surface hardness after quench about 58 HRC (producer data, 20 mm section). Unalloyed steel: hardening is shallow, and thin or complex parts risk distortion and quench cracking. Tempering: Temper immediately after hardening. Tempering hardness values to be taken from the mill or producer tempering diagram [VERIFY — source not confirmed]. Surface Hardening: Flame or induction hardening of local wear faces gives a hard surface over a tough, unhardened core — the usual way to harden 1.1730 mould and fixture parts.
ENGINEERING NOTES
Weldability
Fair

At 0.42–0.50% carbon, 1.1730 can be welded for repairs and attachments but needs preheat to avoid hard, crack-prone heat-affected zones [VERIFY — preheat range to be confirmed from producer welding data]. Use low-hydrogen consumables and slow cooling. Stress relieve at 600–650 °C after significant welding on mould plates to restore flatness and relieve residual stress. Do not weld surface-hardened areas without first annealing or re-tempering.

Filler metals
  • E7018 · AWS A5.1 / SMAWLow-hydrogen electrode for repairs and attachments, with preheat.
  • ER70S-6 · AWS A5.18 / MIG-MAG (GMAW)Solid wire for brackets, lifting lugs and repairs, with preheat.
  • ER70S-2 · AWS A5.18 / TIG (GTAW)Root and fine repair work on plate edges.
Machinability
Excellent

Excellent machinability in the as-delivered condition — the main reason it is chosen for mould bases and fixtures. Mill, drill and tap with HSS or carbide at normal carbon-steel speeds. Stress relieve at 600–650 °C after heavy rough machining of large plates, before finish machining, to hold flatness. Grind surface-hardened faces with plenty of coolant.

Applications

  • Mould bases and bolster plates for plastic injection moulds in UAE and GCC tool rooms
  • Top and bottom clamping plates for plastic and die-casting moulds
  • Die sets, punch holders and back-up plates for press tools
  • Jigs, fixtures and machine-tool holding plates
  • Prototype and short-run moulds for low-volume plastic parts
  • Cold heading die holders and simple blanking tools
  • Hand tools, tongs and agricultural tools — water or flame hardened
  • Leather and soft-material cutting knives
  • Wear strips and guide rails surface hardened by flame or induction
  • Ejector plates and spacer blocks in GCC packaging mould builds

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

1.1730 steel (C45U) is used mainly for mould bases, clamping plates, die sets and fixtures — parts that must machine easily and stay flat but do not need high hardness. Typical uses are bolster and clamping plates for plastic and die-casting moulds, punch holders and back-up plates for press tools, jigs, ejector plates and prototype moulds. It is also water or flame hardened for hand tools, tongs and agricultural tools. In the UAE and GCC, tool rooms use 1.1730 to build the frame of a mould around P20 or 1.2083 cavity plates.

Get in touch

Elevateyourprojectswithoursuperiorsteel