Alloy Steel dealers in UAE

EN41B / 905M39 / 41CrAlMo7-10 Nitriding Steel | Supplier in UAE & GCC

EN41B / 905M39 / 41CrAlMo7-10 — Cr-Al-Mo nitriding steel: about 950 HV nitrided case, the hardest of the nitriding steels, over a 950–1150 MPa Q&T core.

Industries Served

Manufacturing
Automotive
Heavy Engineering
Oil & Gas
Aerospace & Defence

Overview

EN41B (BS 970 905M39, 41CrAlMo7-10 / 1.8509 to EN 10085, French 40CAD6.12) is a chromium-aluminium-molybdenum nitriding steel containing 0.38–0.45% carbon, 1.50–1.80% chromium, 0.20–0.35% molybdenum and 0.80–1.20% aluminium. Aluminium is the key: it forms extremely hard, finely dispersed aluminium nitrides during gas or plasma nitriding at about 480–570°C, giving a surface hardness of about 950 HV — higher than any other common nitriding steel, including the 3% Cr-Mo EN40B. Supplied quenched and tempered to EN 10085 +QT (950–1150 MPa at 16–40 mm), it provides a strong core beneath the hard case, while the low nitriding temperature means no quench, scale-free surfaces and minimal distortion. The trade-off for maximum hardness is a more brittle compound layer and lower core toughness than Cr-Mo nitriding steels, so EN41B suits wear- and fatigue-critical parts that are not subject to heavy shock. Typical uses are extruder and injection-moulding screws and barrels, cylinder liners, hydraulic piston rods, gauges, spindles and camshafts. BS 970 is withdrawn; 41CrAlMo7-10 is the current EN designation.

Nifty Alloys supplies EN41B / 905M39 / 41CrAlMo7-10 nitriding steel from stock in Dubai, UAE, in round bar, quenched and tempered (Condition T / +QT) as standard, with annealed material on request. Bars are cut to length and dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying chemistry (41CrAlMo7-10 or 905M39 as supplied), condition, tensile, impact and hardness results with full traceability to the mill; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.42 %
C

Carbon

0.38 – 0.45 %

Si

Silicon

≤ 0.4 %

Mn

Manganese

0.4 – 0.7 %

1.65 %
Cr

Chromium

1.5 – 1.8 %

0.28 %
Mo

Molybdenum

0.2 – 0.35 %

1 %
Al

Aluminium

0.8 – 1.2 %

P

Phosphorus

≤ 0.025 %

S

Sulfur

≤ 0.035 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10085

EN

Revision: EN 10085:2001

Nitriding steels — Technical delivery conditions. Covers 31CrMoV9 (1.8519), 41CrAlMo7-10, 31CrMo12, 34CrAlMo5-10 and related grades in the quenched and tempered (+QT) and soft annealed (+A) conditions.

Current European standard for nitriding steels (EN 10085:2001); 31CrMoV9 is also listed in ISO 683-5. Formerly DIN 17211. +QT properties are size-banded from 16 to 250 mm.

Available Forms

Round Bar

16–250 mm. Diameter, Q&T; precision ground on request. EN 10085 +QT properties defined to 250 mm. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Quenched & Tempered (+QT / Condition T) — standard stocked condition. Annealed (+A) on request. Nitriding by the customer.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 10085

Designations & Equivalents

StandardDesignationNotes
BSEN41B / EN41 / EN41BTOriginal BS 970:1955 designations
BS905M39BS 970 designation (withdrawn standard)
EN Name41CrAlMo7-10 (formerly 41CrAlMo7)EN 10085 — primary chemistry on this page
EN / Werkstoff1.850941CrAlMo7-10 material number
Common Name40CAD6.12(AFNOR) French designation
Common Name38CrMoAl(GB) Chinese designation
Common Name38Kh2MYuA(GOST) Russian designation
Common NameAluminium nitriding steel / EN41B round bar / nitriding steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition, tensile, impact and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — Not a sour-service grade: Q&T core (about 286–347 HB) and the nitrided case exceed the 22 HRC limit for low-alloy steels.

Specifications

Mechanical Properties

Values per EN 10085. Bar length compares conditions within each row.

PropertyQuenched & Tempered (+QT) | EN 10085Annealed (+A) | EN 10085
Tensile Strength (UTS)950–1150 MPaOver 16 to 40 mmEN 10085 range.–
Tensile Strength (UTS)900–1100 MPaOver 40 to 100 mmEN 10085 range; 850–1050 MPa at 100–160 mm, 800–1000 MPa at 160–250 mm.–
Yield Strength (0.2% Proof Stress)750 MPaminOver 16 to 40 mmEN 10085 minimum; 720 at 40–100, 670 at 100–160, 625 at 160–250 mm.–
Elongation11 %minA (5.65√So) — over 16 to 40 mmEN 10085 minimum; 13% at 40–100, 14% at 100–160, 15% at 160–250 mm.–
Impact Energy (Charpy V-notch)25 Jmin+20°C, over 16 to 40 mmEN 10085 minimum (30 J in larger sections).–
Hardness286–347 HBOver 16 to 40 mmFor information (253–319 HB at 100–160 mm).248 HBmaxSoft annealed (+A)EN 10085 maximum.
Hardness950 HVminNitrided surfaceGuidance — EN 10085 information value; 950–1100 HV typical.–

Physical Properties

PropertyQuenched & Tempered (+QT) | EN 10085Annealed (+A) | EN 10085
Densityat 20°C7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C210 GPa210 GPa
Shear Modulusat 20°C80 GPa80 GPa
Coefficient of Thermal Expansionat 20–100°C12.5 µm/m·°C12.5 µm/m·°C

Service Conditions

Service Temperature

Max 450 °C

Notes

[VERIFY — maxServiceTempC 450: continuous load-bearing limit not confirmed] Nitrided parts retain case hardness up to temperatures approaching the nitriding range (about 480–570°C) for limited exposure; keep continuous service well below the nitriding temperature. Core toughness is modest, so avoid shock loading at low temperatures.

Corrosion Performance

General corrosion

Unprotected Q&T bar rusts in humid, coastal UAE and GCC conditions — store oiled. Not suitable for aggressive chemical media without coating.

Pitting resistance

Base metal has no pitting resistance. The nitrided compound layer gives some improvement in atmospheric corrosion resistance compared with bare steel.

Additional notes

Not applicable — low-alloy steel.

Heat Treatment

HEAT TREATMENT GUIDE — EN41B / 905M39 / 41CrAlMo7-10

Hot forming: 1050–950°C. Soft annealing: 650–750°C, air cool — 248 HB max (+A). Hardening: 870–930°C — quench in oil or polymer. Tempering: 580–700°C, air cool — EN 10085 +QT strength by section (950–1150 MPa at 16–40 mm). Temper at least 30–50°C above the planned nitriding temperature. Stress relieving: 550–570°C, air cool, after rough machining and before final machining. Nitriding: gas nitriding in controlled atmosphere at about 480–570°C (or plasma / salt-bath nitrocarburising at about 570–580°C) — surface about 950 HV (950–1100 HV typical) depending on process and case depth. Final stress relief (if needed): about 50°C below the tempering temperature. Note: the aluminium-nitride case is very hard but more brittle than Cr-Mo nitriding steels — avoid sharp corners and heavy impact on nitrided surfaces.

ENGINEERING NOTES
Weldability
Poor

Welding is not recommended. If unavoidable, weld before nitriding with preheat of about 300°C, low-hydrogen Cr-Mo consumables, controlled interpass temperature and stress relief at about 550°C with furnace cooling. Aluminium can cause oxide inclusions in the weld. Never weld nitrided surfaces — the hard case cracks and nitrogen causes porosity.

Filler metals
  • E9018-B3 · AWS A5.5 / SMAW2.25Cr-1Mo low-hydrogen electrode for repairs before nitriding
  • ER90S-B3 · AWS A5.28 / TIG / MIG2.25Cr-1Mo wire; preheat about 300°C and stress relieve
  • E309L-16 · AWS A5.4 / SMAWAustenitic electrode for non-load-bearing attachments
Machinability
Fair

Machine in the Q&T condition (about 286–347 HB at 16–40 mm) with carbide tooling, or in the annealed condition (248 HB max) for heavy roughing. Stress relieve at about 550–570°C after rough machining, finish-machine or grind, then nitride — growth during nitriding is very small. After nitriding only light grinding or lapping is practical.

Applications

  • Plastic extruder and injection-moulding screws and barrels
  • Cylinder liners and sleeves for engines and compressors
  • Nitrided hydraulic piston rods and cylinders
  • Precision gauges, plug gauges and measuring tools
  • Spindles and quills for machine tools
  • Camshafts and valve-train wear parts
  • Pump plungers and valve stems in GCC process plants
  • Straightening rolls and guide components
  • Bushings and wear sleeves under sliding contact
  • Dies and moulds for polymer processing

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

EN41B / 905M39 / 41CrAlMo7-10 is used for nitrided parts that need the hardest possible wear-resistant surface with minimal distortion: plastic extruder and injection-moulding screws and barrels, cylinder liners, hydraulic piston rods, gauges, spindles, camshafts, pump plungers and straightening rolls. After nitriding it reaches about 950 HV. In the UAE and GCC it is used by plastics processors, hydraulic and pump workshops.

Get in touch

Elevateyourprojectswithoursuperiorsteel