Carbon Steel dealers in UAE

EN32 / 080A15 / C15E Case Hardening Steel | Supplier in UAE & GCC

EN32 / 080A15 / C15E — plain carbon case hardening steel: carburise for a hard wear-resistant case over a tough core; gears, cams, spindles, rollers.

Industries Served

Manufacturing
Automotive
Heavy Engineering
Construction

Overview

EN32 case hardening steel (BS 970 080A15 / 080M15, formerly EN32A / EN32B; EN ISO 683-3 C15E / 1.1141; DIN Ck15; AISI 1015 / 1016; JIS S15C) is a low-carbon non-alloy steel containing 0.13–0.18% carbon (080A15) and 0.70–0.90% manganese, with phosphorus and sulphur limited to 0.050% maximum. Its low carbon gives good weldability and reasonable machinability in the supplied condition, but low hardenability — so it is used almost entirely in the case-hardened (carburised) condition. Carburising enriches the surface with carbon; hardening and low-temperature tempering at 150–200°C then produce a hard, wear-resistant case of typically about 58–62 HRC over a tough, ductile core with a core strength of about 430–490 MPa (blank case hardened, 29 mm test piece: about 430 MPa tensile, 18% elongation and 35 J KCV impact). Because 080A15 is specified by chemical analysis only, mechanical values are typical and depend on section and heat treatment; for higher core strength, alloy case-hardening steels such as 16MnCr5, 8620 or EN36 are used. As a carbon steel it needs surface protection. Typical uses are lightly stressed gears, cams, spindles, rollers, bushes, pins, levers and other wear parts.

Nifty Alloys supplies EN32 / 080A15 / C15E case hardening steel from Dubai, UAE, in round bar — as rolled, normalised or bright drawn for machining before carburising. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

0.15 %
C

Carbon

0.13 – 0.18 %

0.25 %
Si

Silicon

0.1 – 0.4 %

0.8 %
Mn

Manganese

0.7 – 0.9 %

P

Phosphorus

≤ 0.05 %

S

Sulfur

≤ 0.05 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

BS 970-1 (withdrawn)

Other

Revision: BS 970-1 (withdrawn — legacy)

Available Forms

Round Bar

6–150 mm. Diameter, as rolled / normalised / bright. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
As-rolled / normalised round bar [VERIFY — stocked sizes]; bright drawn on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

BS 970-1 (withdrawn)

Designations & Equivalents

StandardDesignationNotes
BSEN32 / EN32A / EN32B / EN32C / EN32MBS 970:1955 designations (EN32B ≈ 080A15)
Common Name080A15 / 080M15(BS 970 (withdrawn)) 080A15 analysis grade; 080M15 mechanical grade
Common NameEN3B(Trade usage) Some stockists sell 080A15 as "EN3B" — see EN3 / 070M20 page
EN NameC15E / C16EEN ISO 683-3 designations
EN / Werkstoff1.1141 / 1.1148(EN Number) C15E / C16E material numbers
AISI / SAE1015 / 1016Nearest US grades
Common NameDIN Ck15 / JIS S15C / SS 1370 / ISO C15E4(Other) National equivalents
EN NameEN 10084 / EN 10277-2(EN (superseded / product)) Superseded case-hardening standard and bright-bar standard — aliases only
Common NameNone(AMS / MIL) No AMS or MIL specification applies (carbon steel)
Common NameEN32 case hardening steel / EN32B bright bar / carburising steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and condition (mechanical values where specified).

Specifications

Mechanical Properties

Values per BS 970-1 (withdrawn). Bar length compares conditions within each row.

PropertyAs-Rolled / Normalised | BS 970-1
Tensile Strength (UTS)430 MPatypicalBlank case hardened, 29 mmTypical — not specified for 080A15.
Tensile Strength (UTS)430–490 MPaCarburised coreTypical core strength range.
Elongation18 %typicalBlank case hardened, 29 mmTypical.
Impact Energy (Charpy V-notch)35 JtypicalBlank case hardened, 29 mmTypical (Izod 39 J).
Hardness58–62 HRCCarburised caseTypical case hardness [VERIFY].

Physical Properties

PropertyAs-Rolled / Normalised | BS 970-1
Densityat 20°C7.85 g/cm³
Modulus of Elasticityat 20°C207 GPa
Thermal Conductivityat 20°C51 W/m·K
Coefficient of Thermal Expansionat 20–100°C11.9 µm/m·°C
Specific Heat Capacityat 20°C460 J/kg·K

Service Conditions

Service Temperature

Max 150 °C

Notes

Case-hardened parts should not be used above the tempering temperature (150–200°C), which would soften the case. Ambient-temperature engineering service.

Corrosion Performance

General corrosion

Rusts in humid and coastal atmospheres — oil or protect finished parts and store under cover in the UAE climate.

Pitting resistance

Not applicable — carbon steel.

Additional notes

No corrosion resistance. Surface protection required.

Heat Treatment

HEAT TREATMENT GUIDE — EN32 / 080A15 / C15E

Supply: as rolled, normalised or bright drawn. Normalising: about 880–920°C, air cool [VERIFY]. Carburising: about 880–920°C in a carbon-rich atmosphere to the required case depth; surfaces must be clean and free of grease. Hardening: direct quench from carburising, or reheat to about 760–780°C (case refining) and quench in water or oil [VERIFY]. Tempering: 150–200°C — recommended for stress relief and maximum case toughness. Typical result: case about 58–62 HRC; core 430–490 MPa (section dependent).

ENGINEERING NOTES
Weldability
Good

Readily welded in the supplied (uncarburised) condition with standard carbon-steel consumables, without preheat in normal sections. Do not weld carburised or hardened surfaces.

Filler metals
  • E7018 · AWS A5.1 / SMAWLow-hydrogen electrode — supplied (uncarburised) condition
  • ER70S-6 · AWS A5.18 / MIG (GMAW)Carbon-steel MIG wire
Machinability
Good

Reasonable machinability in the supplied condition (rated 100 by some UK suppliers on a bright-bar scale). Machine before carburising; finish-grind after hardening.

Applications

  • Case-hardened gears and pinions (lightly stressed)
  • Cams and cam followers
  • Spindles and shafts with wear-resistant journals
  • Rollers and track wheels
  • Bushes, sleeves and wear plates
  • Pins, gudgeon pins and dowels
  • Levers, links and hinge parts
  • Jig and fixture components needing a hard surface
  • Agricultural and automotive wear parts
  • Machined replacement parts for GCC plant maintenance

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

EN32 / 080A15 is used for case-hardened, lightly stressed parts — gears and pinions, cams, spindles, rollers, bushes, pins, levers and wear plates — where a hard, wear-resistant surface is needed over a tough core. In the UAE and GCC it is used for machined and carburised replacement parts.

Get in touch

Elevateyourprojectswithoursuperiorsteel