Alloy Steel dealers in UAE

AISI 8620 / 20NiCrMo2-2 / 1.6523 Case Hardening Steel | Supplier in UAE & GCC

AISI 8620 / 20NiCrMo2-2 (1.6523) — Ni-Cr-Mo case hardening steel: about 61 HRC carburised case over a tough core; gears, pinions, shafts, cams.

Industries Served

Automotive
Oil & Gas
Aerospace & Defence
Heavy Engineering
Mining
Manufacturing

Overview

AISI 8620 (20NiCrMo2-2 / 1.6523, BS 805M20 / EN362, JIS SNCM220) is a low nickel-chromium-molybdenum case-hardening steel, supplied to ASTM A29 for 8620 chemistry, to EN ISO 683-3 (formerly EN 10084) for 20NiCrMo2-2, and to AMS 6274 for aircraft-quality bar and forgings. Its 0.18–0.23% carbon keeps the core tough and machinable, while about 0.55% nickel, 0.5% chromium and 0.2% molybdenum give moderate hardenability and a fine-grained response to carburising. Carburised at 880–980°C and hardened, 8620 develops a hard case of about 61 HRC for wear and contact-fatigue resistance, over a core that typically reaches 980–1270 MPa in small sections and about 690–930 MPa at 63 mm. Double hardening — core hardening at 860–900°C, then case hardening at 780–820°C — refines both case and core. 8620 is the world's most widely used carburising steel for gears, pinions, splined shafts, cams, king pins and bearing races in moderate sections; for heavier, more highly loaded gears, the 3% nickel EN36 gives a stronger core.

Nifty Alloys supplies AISI 8620 / 20NiCrMo2-2 case-hardening steel from stock in Dubai, UAE, in round bar, flat bar and forgings, annealed as standard, with normalised material and AMS 6274 aircraft-quality supply on request. Bars are cut to length and dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying chemistry (8620 or 20NiCrMo2-2 as supplied), condition, hardness and, where specified, Jominy hardenability; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.2 %
C

Carbon

0.18 – 0.23 %

Si

Silicon

0.15 – 0.35 %

Mn

Manganese

0.7 – 0.9 %

0.55 %
Ni

Nickel

0.4 – 0.7 %

0.5 %
Cr

Chromium

0.4 – 0.6 %

0.2 %
Mo

Molybdenum

0.15 – 0.25 %

P

Phosphorus

≤ 0.035 %

S

Sulfur

≤ 0.04 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 683-3

EN

Revision: EN ISO 683-3:2019 — current edition

Heat-treatable steels, alloy steels and free-cutting steels — Part 3: Case-hardening steels. Covers 16MnCr5 (1.7131) and 16MnCrS5 (1.7139) in delivery conditions +A, +N, +FP, +TH and +AC.

Current European standard for case-hardening steels; replaced EN 10084. Specifies chemistry, delivery-condition hardness and Jominy hardenability bands (+H, +HH, +HL).

Available Forms

Flat Bar

10–100 mm. Thickness; width × thickness to order. [VERIFY — stock range not confirmed]

Forging

200–800 mm. Forged blanks and rings to order. [VERIFY — stock range not confirmed]

Round Bar

16–300 mm. Diameter, annealed; bright drawn and ground on request. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (212 HB max) — standard stocked condition. Normalised and AMS 6274 on request. Carburising and hardening by the customer.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 683-3

Designations & Equivalents

StandardDesignationNotes
AISI / SAE8620 / 8620HASTM A29 (8620) / A304 (8620H) — primary chemistry
UNSG86200 / H86200Unified Numbering System
DIN20NiCrMo2-2 (formerly 21NiCrMo2)EN ISO 683-3 (formerly EN 10084)
EN / Werkstoff1.652320NiCrMo2-2 material number
BS805M20 / EN362BS 970 designations (withdrawn standard)
AMSAMS 6274SAE 8620 aircraft-quality bars, forgings and tubing
JISSNCM220Japanese Industrial Standard
Common Name20NCD2(AFNOR) French designation
Common Name20CrNiMo(GB) Chinese designation
Common Name8620 case hardening steel / carburising steel / 8620 round bar / gear steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry (8620 or 20NiCrMo2-2 as supplied), condition, hardness and, on request, Jominy hardenability.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Requires Confirmation8620 contains < 1% Ni, so annealed, normalised or quenched-and-tempered material at 22 HRC maximum may be acceptable under ISO 15156-2 with other conditions met. Carburised and case-hardened parts far exceed 22 HRC and are not acceptable. Confirm project requirements and hardness testing.
AMS 6274ConditionalSupplied on request as aircraft-quality 8620 — confirm revision at enquiry.

Specifications

Mechanical Properties

Values per EN ISO 683-3. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN ISO 683-3Normalised | EN ISO 683-3
Hardness212 HBmaxSoft annealed (+A), 16–100 mmEN ISO 683-3 maximum.149–194 HBFerrite-pearlite (+FP), 16–100 mmEN ISO 683-3 range.
Hardness255 HBmaxSoft annealed + cold drawn (+A+C), 16–100 mmEN ISO 683-3 maximum.–
Hardness61 HRCtypicalCarburised case after hardening and temperingTypical achievable case hardness — process dependent.–
Tensile Strength (UTS)980–1270 MPaCore after case hardening — 11 mmTypical guidance (8620H / 20NiCrMo2-2) — not a supply requirement.–
Yield Strength (0.2% Proof Stress)785 MPaminCore after case hardening — 11 mmTypical guidance; 590 MPa at 30 mm, 490 MPa at 63 mm.–

Physical Properties

PropertyAnnealed (+A) | EN ISO 683-3Normalised | EN ISO 683-3
Densityat 20°C7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C205 GPa205 GPa
Thermal Conductivityat 20°C46 W/m·K46 W/m·K
Coefficient of Thermal Expansionat 20–100°C11.5 µm/m·°C11.5 µm/m·°C

Service Conditions

Service Temperature

Max 150 °C

Notes

Carburised parts are tempered at only 150–200°C, so service above about 150°C softens the case and reduces wear and contact-fatigue resistance. The low-carbon core retains reasonable toughness at sub-zero temperatures; specify core impact testing for cold-climate use.

Corrosion Performance

General corrosion

Corrodes like other low-alloy steels. Carburised and hardened surfaces (about 61 HRC) are susceptible to hydrogen embrittlement from pickling or plating — bake after electroplating.

Pitting resistance

No pitting resistance. Store oiled and under cover in the humid, coastal UAE and GCC climate; protect finished gears with lubricant or coatings.

Additional notes

Not applicable — low-alloy steel.

Heat Treatment

HEAT TREATMENT GUIDE — AISI 8620 / 20NiCrMo2-2 / 1.6523

Forging: 1100–900°C; cool slowly. Normalising: about 860–900°C, air cool. Soft annealing: about 700°C, furnace cool at about 10°C/h to 600°C, then air — 212 HB max (+A). Carburising: 880–980°C (generally not above 950°C if direct hardening) — time per required case depth (for example about 0.5 mm in roughly 4 h). Direct hardening: from carburising, or from 820–860°C, quench in oil or polymer. Double hardening (best properties): core harden 860–900°C, oil; case harden 780–820°C, oil. Tempering: 150–200°C, 1 h minimum — case about 61 HRC. Typical core properties after case hardening (8620H / 20NiCrMo2-2 guidance): 11 mm — 785 MPa min yield, 980–1270 MPa tensile, 9% min A; 30 mm — 590 MPa, 780–1080 MPa, 10%; 63 mm — 490 MPa, 690–930 MPa, 11%. Note: low carbon means 8620 does not respond usefully to flame or induction hardening unless carburised first; it can be nitrided.

ENGINEERING NOTES
Weldability
Good

Weldable in the annealed or normalised condition before carburising — low carbon and moderate alloy content make it one of the more weldable alloy steels. Use low-hydrogen consumables, preheat thicker sections to about 150–200°C [VERIFY — preheat range not confirmed] and stress relieve after welding. Weld only before carburising; never weld case-hardened parts, and mask weld zones from carburising if they must stay soft.

Filler metals
  • E8018-C3 · AWS A5.5 / SMAW1% Ni low-hydrogen electrode — compatible with the Ni-Cr-Mo base
  • ER80S-Ni1 · AWS A5.28 / TIG / MIG1% Ni wire for GTAW / GMAW before carburising
  • E7018 · AWS A5.1 / SMAWGeneral low-hydrogen electrode for non-critical joints
Machinability
Good

Machines well in the annealed (212 HB max) or normalised (149–194 HB) condition; normalised material gives the best finish for gear hobbing and shaping. Complete machining before carburising and leave grinding stock for distortion. After case hardening (about 61 HRC) only grinding is practical.

Applications

  • Gears, pinions and ring gears for automotive and industrial gearboxes
  • Splined shafts, drive shafts and transmission components
  • Camshafts, cam followers and tappets
  • King pins, gudgeon pins, piston pins and bushings
  • Bearing races and rollers in moderate sections
  • Oilfield pump gears, sprockets and rock-bit components in the GCC
  • Aircraft gears and actuator parts to AMS 6274
  • Chain wheels, sprockets and ratchets
  • Mining and construction machinery wear parts
  • Fixtures, jigs and machine parts needing a hard surface with a tough core

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

AISI 8620 is used for carburised, case-hardened parts that need a hard, wear-resistant surface over a tough core: gears, pinions, ring gears, splined shafts, camshafts, king pins, gudgeon pins and bearing races in moderate sections. After carburising it reaches about 61 HRC at the surface. In the UAE and GCC it is used for automotive, oilfield pump and industrial gearbox components, and for aerospace parts to AMS 6274.

Get in touch

Elevateyourprojectswithoursuperiorsteel