Stainless Steel dealers in UAE

FV520B / 1.4594 / X5CrNiMoCuNb14-5 PH Stainless Steel | Supplier in UAE & GCC

FV520B / 1.4594 / X5CrNiMoCuNb14-5 — Mo-Cu precipitation-hardening stainless: 930–1270 MPa aged, anti-galling; turbine blades, pump shafts, valves.

Industries Served

Oil & Gas
Power Generation
Marine
Aerospace & Defence
Heavy Engineering

Overview

FV520B (EN 1.4594 / X5CrNiMoCuNb14-5) is a martensitic precipitation-hardening stainless steel containing 13.0–15.0% chromium, 5.0–6.0% nickel, 1.20–2.00% molybdenum, 1.20–2.00% copper and 0.15–0.60% niobium, with carbon held to 0.07% maximum. Copper provides the precipitation-hardening response, while molybdenum gives better pitting, crevice and intergranular corrosion resistance than 17-4PH — corrosion resistance comparable to 304 in many environments — together with notably good anti-galling behaviour. It is supplied solution treated (+AT, 1200 MPa maximum / 360 HB) for machining, then hardened by a single low-temperature ageing treatment with little distortion. EN 10088-3 defines three aged conditions for bar up to 100 mm: +P930 (930–1100 MPa, 720 MPa proof, 15% elongation, 40 J), +P1000 (1000–1200 MPa, 860 MPa proof) and +P1070 (1070–1270 MPa, 1000 MPa proof, 10% elongation), letting the buyer trade strength against toughness. FV520B is also weldable, which is unusual for a high-strength stainless steel. There is no ASTM or UNS equivalent. Typical uses are steam and gas turbine blades, compressor impellers, pump and valve shafts, high-strength fasteners, hydraulic components and aerospace parts.

Nifty Alloys supplies FV520B / 1.4594 on request from Dubai, UAE, in round bar and forgings — solution treated (+AT) as standard, or aged to +P930, +P1000 or +P1070 to your order. Every supply carries an EN 10204 3.1 Mill Test Certificate stating condition, chemistry, tensile and hardness results; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain, and export to Europe, India and Africa, with lead time confirmed at quotation. Send your size list and required condition to request a quote — quotations are turned around the same day.

Chemical Composition

0.04 %
C

Carbon

≤ 0.07 %

0.4 %
Si

Silicon

≤ 0.7 %

0.6 %
Mn

Manganese

≤ 1 %

P

Phosphorus

≤ 0.04 %

S

Sulfur

≤ 0.015 %

14 %
Cr

Chromium

13 – 15 %

5.5 %
Ni

Nickel

5 – 6 %

1.6 %
Mo

Molybdenum

1.2 – 2 %

1.6 %
Cu

Copper

1.2 – 2 %

0.3 %
Nb

Niobium

0.15 – 0.6 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10088-3

EN

Revision: EN 10088-3:2014 (as amended)

Stainless steels — Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products. European standard covering 1.4542 (X5CrNiCuNb16-4).

EN designation: 1.4542, X5CrNiCuNb16-4. Supplied in solution annealed (+AT) condition.

Available Forms

Forging

100–800 mm. Forged discs, rings and blocks to order. [VERIFY — supply range not confirmed]

Round Bar

10–300 mm. Diameter; EN 10088-3 properties to 100 mm, larger by agreement. [VERIFY — supply range not confirmed]

Stock & delivery

Stock location
Dubai, UAE (supplied to order)
In stock
Available on request — +AT solution treated standard; +P930, +P1000, +P1070 aged to order.
Delivery UAE
Lead time confirmed at quotation
Delivery GCC
Lead time confirmed at quotation — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity; mill minimums may apply

Key standards

EN 10088-3

Designations & Equivalents

StandardDesignationNotes
EN / Werkstoff1.4594EN 10088 material number
EN NameX5CrNiMoCuNb14-5EN 10088 steel name
Common NameFV520B / FV 520 BLegacy British designation — widely used generic grade name
BSBS S143 / S144 / S145UK aerospace bar specifications — aliases only (not selected for Module 2)
Common Name95-16(DEF STAN) UK defence standard reference — aliases only [VERIFY]
UNSS45000 — nearest onlyDifferent chemistry (Cu / Mo levels) — not an equivalent
Common NameNone confirmed(AMS / MIL) No AMS or MIL specification confirmed for 1.4594
Common NamePH stainless / precipitation hardening stainless / 14-5 PH / turbine blade steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — condition, chemistry, tensile and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — 1.4594 is not among the ISO 15156-3 pre-qualified precipitation-hardening grades [VERIFY]. For sour service, specify 17-4PH / 15-5PH H1150D or Alloy 718.

Specifications

Mechanical Properties

Values per EN 10088-3. Bar length compares conditions within each row.

Property+AT Solution Treated | EN 10088-3+P1000 | EN 10088-3+P1070 | EN 10088-3+P930 | EN 10088-3
Tensile Strength (UTS)1200 MPamax+AT, ≤ 100 mmEN 10088-3 maximum.1000–1200 MPa+P1000, ≤ 100 mmEN 10088-3 range.1070–1270 MPa+P1070, ≤ 100 mmEN 10088-3 range.930–1100 MPa+P930, ≤ 100 mmEN 10088-3 range.
Hardness360 HBmax+ATEN 10088-3 maximum.–––
Yield Strength (0.2% Proof Stress)–860 MPamin+P1000EN 10088-3 minimum.1000 MPamin+P1070EN 10088-3 minimum.720 MPamin+P930EN 10088-3 minimum.
Elongation–10 %minA, longitudinalEN 10088-3 minimum.10 %minA, longitudinalEN 10088-3 minimum.15 %minA, longitudinalEN 10088-3 minimum.
Impact Energy (Charpy V-notch)–––40 JminRoom temp, longitudinalEN 10088-3 minimum.

Physical Properties

Property+AT Solution Treated | EN 10088-3+P1000 | EN 10088-3+P1070 | EN 10088-3+P930 | EN 10088-3
Densityat 20°C7.8 g/cm³7.8 g/cm³7.8 g/cm³7.8 g/cm³
Modulus of Elasticityat 20°C200 GPa200 GPa200 GPa200 GPa
Thermal Conductivityat 20°C15 W/m·K15 W/m·K15 W/m·K15 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.8 µm/m·°C10.8 µm/m·°C10.8 µm/m·°C10.8 µm/m·°C

Service Conditions

Service Temperature

Max 350 °C

Notes

EN 10088-3 gives proof-stress values at elevated temperature for aged conditions to about 300–350°C [VERIFY]. Long exposure near the ageing temperature overages the material. Toughness at sub-zero temperatures is best in +P930; specify impact testing where required.

Corrosion Performance

General corrosion

Corrosion resistance comparable to 304 in many environments, with useful resistance to some acids. SCC resistance improves with higher ageing temperature — +P930 preferred for chloride / SCC-prone service.

Pitting resistance

Better pitting, crevice and intergranular corrosion resistance than 17-4PH; low rusting rate in marine and industrial atmospheres.

Additional notes

Not normally quoted for PH grades; Mo addition gives higher pitting resistance than 17-4PH.

Heat Treatment

HEAT TREATMENT GUIDE — FV520B / 1.4594 / X5CrNiMoCuNb14-5

Solution treatment (+AT): 1030–1050°C, cool in oil or air — martensitic, ≤ 1200 MPa / 360 HB. Ageing (from +AT, air cool, EN 10088-3 guidance): +P1070 — 4 h at about 550°C; +P930 — 4 h at about 620°C; +P1000 — intermediate ageing [VERIFY — temperature]. Double-overaged route (common UK practice): about 750°C then 550°C, for improved toughness and machinability. Dimensional change on ageing is small — finish-machine before ageing where possible. Re-solution treat before re-ageing to a different condition. Weld in +AT or overaged condition, then re-solution treat and age.

ENGINEERING NOTES
Weldability
Good

Weldable by GTAW, GMAW and SMAW — better than most high-strength martensitic grades. Weld in the solution-treated or overaged condition, then re-solution treat and age for full properties, or age directly after welding where reduced joint strength is acceptable. Matching FV520B-type filler gives an age-hardenable weld; austenitic fillers (ER309L) are used for non-hardened joints [VERIFY — filler designation].

Filler metals
  • 14-5 Mo-Cu-Nb PH type · Matching PH filler / TIGAge-hardenable matching filler [VERIFY — designation]
  • ER630 · AWS A5.9 / TIG / MIGPH-type filler where matching wire is unavailable (lower Mo)
  • ER309L · AWS A5.9 / TIG / MIGAustenitic filler for non-hardened or dissimilar joints
Machinability
Fair

Machine in the +AT or overaged condition with carbide tooling; ageing causes only small dimensional change, so parts can be finish-machined before ageing. Good anti-galling behaviour in service.

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

FV520B / 1.4594 is used for steam and gas turbine blades, compressor impellers, pump and valve shafts, high-strength fasteners, hydraulic and actuator components, aerospace parts and anti-galling sliding components. In the UAE and GCC it is specified for power-generation, oil and gas and marine rotating equipment.

Get in touch

Elevateyourprojectswithoursuperiorsteel