Tool Steel dealers in UAE

1.2083 / X40Cr14 / 420 Mod Stainless Mould Steel | Supplier in UAE & GCC

1.2083 (X40Cr14 / 420 mod) — 13% Cr stainless mould steel with good polishability and corrosion resistance for PVC, medical and food-packaging moulds.

Industries Served

Mould & Die
Manufacturing
Food Processing
Medical
Automotive

Overview

1.2083 stainless mould steel (DIN 1.2083 / X40Cr14, AISI 420 modified) is a martensitic corrosion-resistant tool steel containing 0.36–0.42% carbon and 12.5–14.5% chromium, specified to EN ISO 4957. The chromium level keeps enough chromium in solution after hardening to resist corrosion from aggressive polymers, cooling water and humid storage, while the 0.4% carbon gives a martensite hard enough for wear-resistant, highly polishable cavities. Hardened from 1000–1050 °C and tempered at 200–300 °C, 1.2083 reaches about 52–55 HRC, the range that gives its best corrosion resistance and polish. It is also supplied pre-hardened to 29–33 HRC for moulds machined straight to size without heat treatment. Compared with 420 stainless bar grades such as 1.4028, it has tighter, higher carbon and is made to tool steel cleanliness and quality. It is the standard choice for PVC, acetate, medical and food-packaging moulds.

Nifty Alloys supplies 1.2083 / X40Cr14 stainless mould steel from stock in Dubai, UAE, in plate / block and round bar, annealed for machining and hardening or pre-hardened to 29–33 HRC. Sizes on hand are confirmed with every quotation, and blocks can be saw-cut to your mould dimensions. Every order carries an EN 10204 3.1 Mill Test Certificate as standard, confirming chemistry and hardness with full traceability to the producing mill. EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours and to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain, and export to Europe, India and Africa. As an ISO 9001:2015 certified mould steel supplier in the UAE, our team can help you choose between 1.2083, P20 and H13 for your mould. Contact our team to request a quote.

Chemical Composition

0.4 %
C

Carbon

0.36 – 0.42 %

Si

Silicon

≤ 1 %

Mn

Manganese

≤ 1 %

P

Phosphorus

≤ 0.03 %

S

Sulfur

≤ 0.03 %

13.5 %
Cr

Chromium

12.5 – 14.5 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 4957

EN

Revision: EN ISO 4957:2018

Tool steels — specification for chemical composition, heat treatment, and properties of tool steels including cold work, hot work, and high-speed grades.

Published as BS EN ISO 4957; leading BS dropped to match house style. European standard governing 1.2379 (X153CrMoV12) and other DIN tool steel grades. Supersedes former DIN 17350 for tool steels. Referenced in European and Middle Eastern engineering procurement. Equivalent German standard: DIN EN ISO 4957.

Available Forms

Plate / Block

10–100 mm. Thickness. Saw-cut or milled to mould size. Stocked in Dubai — sizes on hand confirmed at enquiry.

Round Bar

10–250 mm. Diameter. Stocked in Dubai — sizes on hand confirmed at enquiry.

Stock & delivery

Stock location
Dubai, UAE
In stock
1.2083 held in Dubai stock in Annealed and Pre-Hardened 29–33 HRC conditions; sizes and condition on hand confirmed with each quotation. [VERIFY with sales — which conditions and forms are on the shelf] ESR (electro-slag remelted) quality for mirror-polish moulds: ask at enquiry.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 4957

Designations & Equivalents

StandardDesignationNotes
EN / Werkstoff1.2083European material number — primary designation. Not 1.4110 (a different EN 10088 stainless grade).
DINX40Cr14German / EN designation
EN NameX40Cr14EN ISO 4957 steel name
ISOX40Cr14ISO 4957 designation
AISI / SAE420 ModNearest AISI type — a high-carbon 420. Standard AISI 420 stainless bar (ASTM A276) has a wider, lower carbon range.
ASTMA681 (420 modified) — alias only420 is not a listed type in ASTM A681; AISI 420 stainless bar is covered by ASTM A276. Supplied to EN ISO 4957.
AMSNoneNo AMS specification applies to 1.2083 — not an aerospace procurement grade
Common NameStainless mould steel, 420 mould steel, 2083 steel, Z40C14 (AFNOR), F.5263 (UNE), 40Kh13 (GOST)Buyer search terms used in UAE / GCC and Europe

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableMill Test Certificate provided as standard. Confirms chemistry and hardness (annealed or pre-hardened) to EN ISO 4957.

Specifications

Mechanical Properties

Values per EN ISO 4957. Bar length compares conditions within each row.

PropertyAnnealed | EN ISO 4957Pre-Hardened 29–33 HRC | EN ISO 4957
Hardness (annealed)241 HBmaxSurface, as suppliedMax per EN ISO 4957.–
Tensile Strength (UTS)–Room tempNot specified for annealed tool steel — leave blank.1000 MPatypicalRoom tempApproximate conversion from 29–33 HRC (about 950–1050 MPa) — typical, not a specified value.
Yield Strength (0.2% Proof Stress)–Room tempNot specified — leave blank.–Room temp[VERIFY — source not confirmed]. Leave blank until mill data available.
Elongation–Not specified — leave blank.–[VERIFY — source not confirmed]. Leave blank until mill data available.
Hardness (hardened & tempered)54 HRCtypical1000–1050 °C + 200–250 °C temperTypical — producer data (52–56 HRC range). Not a specified value.–
Hardness–29–33 HRCTypical 31 HRCSurface, as suppliedSupply condition per metallurgist brief. Typical value mid-range.

Physical Properties

PropertyAnnealed | EN ISO 4957Pre-Hardened 29–33 HRC | EN ISO 4957
Densityat 20°C7.8 g/cm³7.8 g/cm³
Modulus of Elasticityat 20°C–[VERIFY — source not confirmed]. Leave blank until confirmed.–[VERIFY — source not confirmed]. Leave blank until confirmed.
Thermal Conductivityat 20°C24.6 W/m·K24.6 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.5 µm/m·°C10.5 µm/m·°C
Specific Heat Capacityat 20°C–[VERIFY — source not confirmed]. Leave blank until confirmed.–[VERIFY — source not confirmed]. Leave blank until confirmed.
Melting Point / Rangeat Solidus–[VERIFY — source not confirmed]. Leave blank until confirmed.–[VERIFY — source not confirmed]. Leave blank until confirmed.

Service Conditions

Service Temperature

Max 200 °C

Notes

For moulds hardened and tempered at 200–300 °C, keep the mould below its tempering temperature; about 200 °C is the practical continuous limit, which covers normal thermoplastic and thermoset moulding. Pre-hardened 29–33 HRC material is high-tempered at the mill and is dimensionally stable at mould temperatures. 1.2083 is not a hot work steel — use H13 / 1.2344 for die casting or high-temperature moulds.

Corrosion Performance

PREN 13.5

General corrosion

Best corrosion resistance is in the hardened condition tempered at 200–300 °C with a polished surface. High-temperature tempering — as used for the pre-hardened 29–33 HRC condition — precipitates more chromium carbide and gives somewhat lower corrosion resistance. Keep moulds clean and dry between runs; in humid UAE and GCC workshops, 1.2083 avoids the cooling-channel rust common with P20 moulds.

Pitting resistance

Moderate. Resists cooling water, humid air and the HCl released by PVC moulding far better than P20 or H13, but will pit in strong chloride exposure such as seawater or salt spray. Not suitable for marine service parts.

PREN notes

PREN = %Cr + 3.3×%Mo + 16×%N, calculated on nominal 13.5% Cr (no Mo). The effective value is lower because part of the chromium is bound in carbides. Use only for comparison with other mould steels.

Heat Treatment

ProcessTemperatureCoolingResult & notes
HEAT TREATMENT GUIDE1.2083 / X40Cr14 / 420 Mod: Soft Annealing: 760–800 °Chold until uniformly heated throughslow furnace cooling — max 241 HB. Stress Relieving: About 650 °C (600–650 °C) — minimum 2 h — slow furnace cooling. After heavy rough machining, before finish machining and hardening. Preheating: In stages at approximately 400 °C, 650 °C and 850 °C. Protect against decarburisation (vacuum, protective atmosphere or packing) — a decarburised skin will not polish and loses corrosion resistance. Hardening: Austenitise at 1000–1050 °C — hold 15–30 min after through-heating — cool in oil, pressurised gas (vacuum furnace), air, or a 500–550 °C hot bath (lowest distortion). Do not let the mould cool to room temperature; start tempering from about 80 °C. Tempering: Heat immediately after hardening. 1 hour per 20 mm thickness, minimum 2 hours. Temper at least twice. Typical hardness after tempering: 100 °C — 56 HRC; 200 °C — 54–55 HRC; 300 °C — 52 HRC; 400 °C — 51–54 HRC; 500 °C — 52–53 HRC; 600 °C — 34–40 HRC. For best corrosion resistance and polish, temper at 200–300 °C (about 250 °C is a good balance). Pre-Hardened 29–33 HRC: Supplied hardened and high-temperature tempered at the mill. Machine directly to size; no further hardening needed. Stress relieve after heavy machining at a temperature below the mill tempering temperature [VERIFY — confirm stress-relief temperature with the producing mill]. Polishing: Polish after final heat treatment. Use ESR quality for optical and mirror-finish moulds. Post-weld: Re-temper about 20–30 °C below the last tempering temperature.
ENGINEERING NOTES
Weldability
Fair

1.2083 is not used for structural welds, but mould repair welding is routine with TIG or laser using matching-composition filler. At 0.4% carbon and 13% chromium the weld zone hardens on cooling, so preheat, interpass control and slow cooling are needed [VERIFY — preheat range to be confirmed from producer welding data]. Repair in the annealed or pre-hardened condition where possible. Hardened moulds must be re-tempered about 20–30 °C below their last tempering temperature after welding. A matching filler is essential where the repaired area will be polished, to avoid colour and texture differences.

Filler metals
  • 1.2083-type matching rod (X40Cr14) · Mould repair rod / TIG (GTAW)Matching chemistry and polish response for cavity repair. [VERIFY — consumable code and classification to be confirmed with consumable supplier]
  • 1.2083-type matching wire · Mould repair wire / LaserFor fine edge and parting-line repair with low heat input. [VERIFY — consumable code to be confirmed with consumable supplier]
Machinability
Good

Annealed (≤241 HB): machines readily with coated carbide or HSS. Pre-hardened (29–33 HRC): machine with coated carbide at reduced speed — no further heat treatment needed. Stress relieve annealed blocks at about 650 °C after heavy rough machining, before finish machining and hardening. Hardened moulds polish well; for mirror finishes on optical parts, specify ESR quality. Leave EDM white layer for removal by stoning or polishing, and re-temper after heavy EDM work.

Applications

  • Injection moulds for PVC pipe fittings and profiles in UAE and GCC pipe plants
  • Moulds for acetal (POM), flame-retardant and other corrosive polymers
  • Cavities and cores for glass- and mineral-filled engineering plastics
  • High-gloss moulds for lenses, lamp covers and cosmetic packaging
  • Closure, cap and container moulds for GCC food and beverage packaging
  • Medical and pharmaceutical device moulds — syringes, housings, lab ware
  • Rubber moulds and compression moulds for thermoset materials
  • Mould inserts with internal cooling channels where rust would block water flow
  • Extrusion dies and calibrators for PVC window and door profiles
  • Pre-hardened mould plates and bolsters for humid or corrosive workshop conditions

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

1.2083 stainless mould steel (X40Cr14) is used for plastic moulds that must resist corrosion and take a high polish. Typical uses are injection moulds for PVC fittings and profiles, moulds for acetal and flame-retardant polymers, glass-filled engineering plastics, lenses and cosmetic packaging, food and beverage closures, and medical device housings. Hardened to about 52–55 HRC, its 13% chromium protects cavities and cooling channels from corrosive gases and water. In the UAE and GCC it is widely used by pipe-fitting, packaging and medical moulders working in humid conditions.

Get in touch

Elevateyourprojectswithoursuperiorsteel