Stainless Steel dealers in UAE

440C / 1.4125 / X105CrMo17 Martensitic Stainless Steel | Supplier in UAE & GCC

440C / 1.4125 / X105CrMo17 — hardest standard stainless steel: 58–60 HRC hardened, high wear resistance; bearings, valve balls, knives and surgical tools.

Industries Served

Aerospace & Defence
Oil & Gas
Food Processing
Manufacturing
Mould & Die

Overview

440C stainless steel (UNS S44004, EN 1.4125 / X105CrMo17, ASTM A276, AMS 5630) is a high-carbon chromium-molybdenum martensitic stainless steel containing 0.95–1.20% carbon, 16.0–18.0% chromium and 0.40–0.80% molybdenum. It has the highest carbon content of the 400 series, forming a large volume of hard chromium carbides, and after hardening and tempering reaches about 58–60 HRC — the highest hardness and wear resistance of any standard stainless steel. Chromium is still sufficient to keep it stainless in fresh water, steam, food acids and mild atmospheres. It is supplied soft annealed for machining — 285 HB maximum to EN 10088-3, 269 HB to ASTM A276 and 255 HB to the tighter AMS 5630 — and is hardened from 1000–1050°C in oil, air or polymer, then tempered: about 60 HRC at 100°C, 57 HRC at 300°C and a secondary peak of about 58 HRC at 450–500°C, falling sharply above 550°C. 440C and 1.4125 are essentially equivalent; AMS 5630 adds tighter molybdenum, nickel and copper limits for aerospace bearings. Typical uses are stainless ball and roller bearings, valve balls and seats, needle valves, nozzles, surgical instruments, cutlery and wear parts.

Nifty Alloys supplies 440C / 1.4125 stainless steel from Dubai, UAE, in round bar and flat bar, soft annealed, with hardened and tempered material and AMS 5630 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard, with chemistry and annealed hardness; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list to request a quote — quotations are turned around the same day.

Chemical Composition

1.05 %
C

Carbon

0.95 – 1.2 %

0.4 %
Si

Silicon

≤ 1 %

0.5 %
Mn

Manganese

≤ 1 %

P

Phosphorus

≤ 0.04 %

S

Sulfur

≤ 0.03 %

17 %
Cr

Chromium

16 – 18 %

0.6 %
Mo

Molybdenum

0.4 – 0.8 %

Ni / Cu
Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN 10088-3

EN

Revision: EN 10088-3:2014

Stainless steels — Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products. European standard covering 1.4542 (X5CrNiCuNb16-4).

EN designation: 1.4542, X5CrNiCuNb16-4. Supplied in solution annealed (+AT) condition.

Available Forms

Flat Bar

3–50 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Round Bar

3–200 mm. Diameter, annealed; precision ground on request. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A) — standard [VERIFY — stock status]; hardened & tempered and AMS 5630 on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN 10088-3

Designations & Equivalents

StandardDesignationNotes
AISI / SAE440C / SAE 51440CASTM A276 Type 440C
UNSS44004Unified Numbering System
EN / Werkstoff1.4125EN 10088-3 material number
EN NameX105CrMo17EN 10088 steel name
AMSAMS 5630Bar, wire, forgings, tubing, rings — annealed (Module 2)
AMSAMS 5880 / AMS 5618Other 440C aerospace specifications — aliases only [VERIFY — scope]
Common NameZ100CD17(AFNOR / AIR) French designation
JISSUS440CJapanese Industrial Standard
Common Name108Cr17 / 11Cr17(GB) Chinese designation
Common Name95Kh18(GOST) Russian designation
Common Name440C stainless / stainless bearing steel / hardest stainless steel / knife steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry and annealed hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — High-carbon 440-series martensitic grade — not used for sour service.
AMS 5630ConditionalSupplied to AMS 5630 on request — tighter chemistry and 255 HB max annealed; confirm revision.

Specifications

Mechanical Properties

Values per EN 10088-3. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN 10088-3Hardened & Tempered | EN 10088-3
Hardness285 HBmaxAnnealed (+A), ≤ 100 mmEN 10088-3 maximum.58–60 HRCHardened 1000–1050°C, tempered 100–200°CTypical — not specified.
Hardness269 HBmaxAnnealed — ASTM A276ASTM maximum.–
Hardness255 HBmaxAnnealed — AMS 5630AMS maximum (on request).–
Tensile Strength (UTS)760 MPatypicalAnnealedTypical — not specified.1970 MPatypicalHardened, tempered about 150°CTypical — not specified [VERIFY].
Yield Strength (0.2% Proof Stress)–1900 MPatypicalHardened, tempered about 150°CTypical — not specified [VERIFY].
Elongation–2 %typicalHardened, tempered about 150°CTypical — very low ductility.

Physical Properties

PropertyAnnealed (+A) | EN 10088-3Hardened & Tempered | EN 10088-3
Densityat 20°C7.7 g/cm³7.7 g/cm³
Modulus of Elasticityat 20°C215 GPa215 GPa
Thermal Conductivityat 20°C24 W/m·K24 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.4 µm/m·°C10.4 µm/m·°C
Electrical Resistivityat 20°C0.6 µΩ·m0.6 µΩ·m

Service Conditions

Service Temperature

Max 425 °C

Notes

Not usually recommended above about 425°C — corrosion resistance falls when tempered or used above this temperature, and hardness drops sharply above about 550°C. Low toughness at sub-zero temperatures; not for shock loading.

Corrosion Performance

PREN 19

General corrosion

Best corrosion resistance in the hardened, low-tempered (about 150–200°C) and polished condition; reduced in the annealed state and after tempering above about 425°C. Passivate after finishing; keep clean in the humid, coastal UAE climate.

Pitting resistance

Moderate — resists fresh water, steam, food acids, crude oil and mild atmospheres; not for seawater or chloride-rich media.

PREN notes

PREN ≈ 18–20 calculated (Cr + 3.3Mo); effective resistance lower because much chromium is in carbides.

Heat Treatment

HEAT TREATMENT GUIDE — 440C / 1.4125 / X105CrMo17

Hot working: 1100–900°C; cool slowly (furnace or ash). Soft annealing: 780–840°C, slow furnace cooling — 285 HB max (EN), 269 HB (A276), 255 HB (AMS 5630). Sub-critical annealing 730–770°C, air cool. Stress relieving: about 650–700°C after rough machining. Hardening: preheat to about 760–800°C, austenitise at 1000–1050°C (BGH: 1010–1070°C); quench in oil, air or polymer — about 60 HRC as quenched. Tempering (Lucefin, Ø16 mm quenched 1020°C oil): 100°C ≈ 60 HRC; 200°C ≈ 59; 300–400°C ≈ 57; 450–500°C ≈ 58 (secondary peak); 550°C ≈ 46; 600°C ≈ 41. Temper at 100–200°C for maximum hardness and corrosion resistance; avoid 425–550°C where corrosion resistance falls. Sub-zero treatment optional for dimensional stability of bearings.

ENGINEERING NOTES
Weldability
Poor

Not recommended for welding — the high carbon content makes the weld zone air-harden and crack. If an unavoidable repair is made, preheat to about 250–300°C, use an austenitic filler such as E309 / E312, and anneal immediately afterwards. Design parts to avoid welding.

Filler metals
  • E309-16 · AWS A5.4 / SMAWAustenitic electrode for non-load-bearing repairs; anneal after welding
  • E312-16 · AWS A5.4 / SMAWAustenitic electrode tolerant of high-carbon dilution — repairs only
Machinability
Poor

Machine only in the annealed condition with carbide or ceramic tooling, rigid set-ups and chip breakers — the hard carbides cause high tool wear. After hardening, finish by grinding; avoid overheating during grinding, which lowers hardness and corrosion resistance.

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

440C is used where maximum hardness and wear resistance are needed with stainless properties: stainless ball and roller bearings, valve balls and seats, needle valves, nozzles, surgical instruments, cutlery, gauge blocks, bushings and wear parts. In the UAE and GCC it is used for valve, pump, bearing and food-processing components.

Get in touch

Elevateyourprojectswithoursuperiorsteel