Tool Steel dealers in UAE

D3 / 1.2080 / X210Cr12 Cold Work Tool Steel | Supplier in UAE & GCC

D3 (1.2080 / X210Cr12) — 12% Cr ledeburitic cold work tool steel with very high abrasive wear resistance for blanking dies, shear blades and ceramic moulds.

Industries Served

Mould & Die
Manufacturing
Automotive
Construction
Heavy Engineering

Overview

D3 tool steel (AISI D3 / DIN 1.2080 / X210Cr12, UNS T30403, JIS SKD1) is a high-carbon, high-chromium ledeburitic cold work tool steel containing approximately 2.0% carbon and 12% chromium, specified to ASTM A681 and EN ISO 4957. This chemistry produces a high volume of hard, chromium-rich M7C3 primary carbides, which gives D3 higher abrasive wear resistance than D2 / 1.2379. The trade-off is toughness: with no molybdenum or vanadium addition, D3 is more prone to chipping and edge cracking under impact. D3 is oil hardened from 930–980 °C to about 64 HRC and normally tempered at 150–250 °C for a working hardness of 60–63 HRC. Unlike D2 it shows no secondary hardening, so hardness falls steadily as tempering temperature rises. It is supplied soft annealed to a maximum of 248 HB (EN ISO 4957) / 255 HB (ASTM A681). Typical uses are blanking and punching dies for thin abrasive sheet, shear blades, ceramic and brick press moulds, and powder compaction tooling.

Nifty Alloys supplies D3 / 1.2080 / X210Cr12 tool steel through our Dubai, UAE facility in round bar, flat bar and plate / block, soft annealed and ready for machining and heat treatment. D3 is supplied on request against your order, and D2 / 1.2379 is held in Dubai stock where a tougher 12% Cr alternative suits the tool. All material is supplied with EN 10204 3.1 Mill Test Certificates as standard, confirming chemistry and annealed hardness with full traceability to the producing mill. EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE and the GCC — Saudi Arabia, Kuwait, Qatar, Oman and Bahrain — and export to Europe, India and Africa. As an ISO 9001:2015 certified tool steel supplier in the UAE, our team can advise on D3, D2 or D6 selection for your die. Contact our team to request a quote.

Chemical Composition

2.05 %
C

Carbon

1.9 – 2.2 %

0.3 %
Si

Silicon

0.1 – 0.6 %

0.3 %
Mn

Manganese

0.2 – 0.6 %

P

Phosphorus

≤ 0.03 %

S

Sulfur

≤ 0.03 %

12 %
Cr

Chromium

11 – 13 %

V

Vanadium

W

Tungsten

Ni + Cu
Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 4957

EN

Revision: EN ISO 4957:2018 / ASTM A681-08 (2022)

Tool steels — specification for chemical composition, heat treatment, and properties of tool steels including cold work, hot work, and high-speed grades.

Published as BS EN ISO 4957; leading BS dropped to match house style. European standard governing 1.2379 (X153CrMoV12) and other DIN tool steel grades. Supersedes former DIN 17350 for tool steels. Referenced in European and Middle Eastern engineering procurement. Equivalent German standard: DIN EN ISO 4957.

Available Forms

Flat Bar

10–200 mm. Thickness. Widths to order; saw-cut from block where needed. Supplied on request.

Plate / Block

10–100 mm. Thickness. Saw-cut to customer dimensions. Supplied on request.

Round Bar

10–300 mm. Diameter. Typical mill range, supplied on request — confirm size and lead time at enquiry.

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed — D3 / 1.2080 is supplied on request (not held as Dubai stock); lead time confirmed at quotation. D2 / 1.2379 annealed is held in Dubai stock as an alternative. UAE / GCC delivery times apply from dispatch.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 4957

Designations & Equivalents

StandardDesignationNotes
AISI / SAED3Primary designation
UNST30403Unified Numbering System
EN / Werkstoff1.2080European material number
DINX210Cr12German designation (formerly DIN 17350)
EN NameX210Cr12EN ISO 4957 steel name
ISOX210Cr12ISO 4957 designation
ASTMA681 (D3)ASTM product standard
BSBD3BS 4659 — withdrawn, legacy UK designation
JISSKD1Japanese Industrial Standard (JIS G4404). Note: SKD11 is D2, not D3
Common NameZ200C12(AFNOR) French designation (legacy NF A35-590)
Common NameX205Cr12KU(UNI) Italian designation (legacy)
Common NameF.5212(UNE) Spanish designation (legacy)
Common NameCr12(GB) Chinese standard GB/T 1299
Common NameKh12 (Х12)(GOST) Russian designation
AMSNoneNo AMS specification applies to D3 / 1.2080 — not an aerospace procurement grade
Common NameD3 tool steel, 12% chromium tool steel, HCHCr die steel, ledeburitic cold work steelBuyer search terms used in UAE / GCC and Europe

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableMill Test Certificate provided as standard. Confirms chemistry and annealed hardness to EN ISO 4957 / ASTM A681.

Specifications

Mechanical Properties

Values per EN ISO 4957. Bar length compares conditions within each row.

PropertyAnnealed | EN ISO 4957 / ASTM A681
Hardness (annealed)248 HBmaxSurface, as suppliedMax per EN ISO 4957. ASTM A681 max 255 HB (269 HB cold drawn).
Tensile Strength (UTS)–Room tempNot specified by EN ISO 4957 or ASTM A681 for annealed tool steel — leave blank.
Yield Strength (0.2% Proof Stress)–Room tempNot specified — leave blank.
Elongation–Not specified — leave blank.
Hardness (hardening response)61 HRCminTypical 62 HRC954–968 °C / oil / 204 °C temper 2 hMinimum per ASTM A681 Table 3. Typical 62 HRC after 200 °C temper (producer data) — typical.
Hardness (as quenched)64 HRCtypical930–980 °C, oil quenchTypical — producer data. Not a specified value.

Physical Properties

PropertyAnnealed | EN ISO 4957 / ASTM A681
Densityat 20°C7.7 g/cm³
Modulus of Elasticityat 20°C210 GPa
Thermal Conductivityat 20°C16.7 W/m·K
Coefficient of Thermal Expansionat 20–100°C10.8 µm/m·°C
Specific Heat Capacityat 20°C460 J/kg·K
Melting Point / Rangeat Solidus–[VERIFY — source not confirmed]. Leave blank until confirmed.

Service Conditions

Service Temperature

Max 200 °C

Notes

D3 is a cold work steel: the working temperature of the tool must stay below its final tempering temperature, otherwise it softens. At the normal 200 °C temper (about 62 HRC), the continuous working limit is about 200 °C. Hardness falls to about 54 HRC after tempering at 500 °C and 46 HRC at 600 °C — D3 has no secondary hardening and no useful hot hardness. Use H13 / 1.2344 class hot work steels for elevated-temperature tooling. Toughness is low at all temperatures; avoid impact loading and thermal shock.

Corrosion Performance

General corrosion

Better resistance to light atmospheric staining than low-alloy tool steels, but D3 will rust in humid or coastal conditions such as the UAE and GCC. Store under cover with rust-preventive oil. Where corrosion resistance is needed (e.g. PVC moulds), specify 1.2083 / X40Cr14. PVD coatings can be applied to hardened D3 for added wear resistance.

Pitting resistance

No meaningful pitting resistance in chloride environments. D3 is not a stainless or corrosion-resistant mould steel.

Additional notes

Not applicable — tool steel. Although D3 contains about 12% chromium, most of it is bound in M7C3 carbides, so the matrix does not passivate like a stainless steel.

Heat Treatment

ProcessTemperatureCoolingResult & notes
HEAT TREATMENT GUIDED3 / 1.2080 / X210Cr12: Soft Annealing: 800–840 °Chold until uniformly heated throughcontrolled slow furnace cooling — max 248 HB (EN ISO 4957) / 255 HB (ASTM A681). Stress Relieving: 650–700 °C — after heavy rough machining or for complex shapes — slow furnace cooling. Carry out before finish machining and hardening. Preheating: In stages at approximately 400 °C, 650 °C and 850 °C to limit distortion and cracking risk in this high-carbon steel. Hardening: Austenitise at 930–980 °C (ASTM A681 reference: 954–968 °C) — hold 15–30 min after through-heating — quench in oil, or in a hot bath at 500–550 °C followed by air cooling (preferred for lowest distortion). Sections up to about 30 mm can be air hardened from 950–980 °C. As-quenched hardness approximately 64 HRC. Tempering: Start immediately when the tool reaches about 80 °C — do not let it cool to room temperature. Typical temper 150–250 °C for 60–63 HRC. Minimum two tempers; 1 hour per 20 mm thickness, minimum 2 hours per temper. Typical hardness after tempering: 100 °C — 63 HRC; 200 °C — 62 HRC; 300 °C — 59 HRC; 400 °C — 57 HRC; 500 °C — 54 HRC; 600 °C — 46 HRC. No secondary hardening peak. Hardening response (ASTM A681 test): austenitise 954 °C (salt bath) or 968 °C (controlled atmosphere), 10–20 min, oil quench, single 2 h temper at 204 °C — minimum 61 HRC. Surface Treatment: PVD coating of hardened tools is common. Nitriding is possible but its 500 °C+ process temperature lowers core hardness to about 54 HRC or less. Post-weld Stress Relief (annealed material): 650 °C — furnace cooling.
ENGINEERING NOTES
Weldability
Poor

D3 / 1.2080 is not welded for structural joints — its ~2% carbon and high carbide content make it highly crack-sensitive. Repair welding of dies is possible only under strict control: preheat to 250–300 °C and hold interpass at or above preheat; use low-hydrogen practice; cool slowly. Annealed material: stress relieve at 650 °C with furnace cooling after welding. Hardened tools must be re-tempered after repair — consult us before welding a hardened D3 tool.

Filler metals
  • ER312 · AWS A5.9 / TIG (GTAW)Buffer (buttering) layer on crack-sensitive high-carbon base metal before hard build-up. Not a matching-hardness deposit.
  • Cold work matching rod, 56–62 HRC deposit · Tool-steel repair rod / TIG (GTAW)For edge and surface build-up on dies. [VERIFY — consumable code and classification to be confirmed with consumable supplier]
Machinability
Fair

Machine only in the soft-annealed condition (≤248 HB). The high volume of primary chromium carbides is abrasive to cutting tools — use coated carbide for turning and milling, cobalt HSS for drilling and tapping at reduced speed. Stress relieve at 650–700 °C after heavy rough machining, before finish machining and hardening. After hardening, grind with soft, open-structure wheels and plenty of coolant to avoid grinding cracks and tempering burns.

Applications

  • Blanking and punching dies for thin, abrasive sheet in long production runs
  • Shear blades and slitting knives for cold cutting of thin strip, paper and film
  • Press-mould liners for brick, tile and concrete block plants in the UAE and GCC
  • Powder compaction dies and punches for metal and ceramic powder pressing
  • Thread-rolling dies and cold-forming rolls for fastener manufacture
  • Deep-drawing and ironing dies for cans and pressed hollow-ware
  • Wire-drawing dies, guide rolls and straightening rolls in wire and bar mills
  • Granulator and pelletiser knives for plastics recycling and packaging lines
  • Wear plates, guides and liners for cement and aggregate handling in GCC construction
  • Plug gauges, ring gauges and measuring tools needing high wear resistance
  • Coining and embossing dies for low-impact, high-wear stamping

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

D3 tool steel (1.2080 / X210Cr12) is used for cold work tooling where abrasive wear, not impact, limits tool life. Typical parts are blanking and punching dies for thin sheet, shear blades and slitting knives, brick, tile and ceramic press-mould liners, powder compaction dies, thread-rolling dies, deep-drawing dies and gauges. Hardened and tempered to 60–63 HRC, its large chromium carbides resist abrasion from sheet edges, ceramic powders and mineral fillers. In the UAE and GCC, D3 is specified mainly for brick and block plant tooling, packaging and plastics recycling knives, and long-run stamping dies.

Get in touch

Elevateyourprojectswithoursuperiorsteel