Tool Steel dealers in UAE

O1 / 1.2510 / 100MnCrW4 Oil Hardening Tool Steel | Supplier in UAE & GCC

O1 / 1.2510 / 100MnCrW4 — oil-hardening cold-work tool steel: 229 HB max annealed, 58–64 HRC hardened, dimensionally stable; gauges, punches, knives.

Industries Served

Manufacturing
Mould & Die
Automotive

Overview

O1 / 1.2510 (100MnCrW4 to EN ISO 4957; near-equivalent AISI O1 to ASTM A681; formerly BS 4659 BO1; French 90MWCV5) is a medium-alloyed, oil-hardening cold-work tool steel, often called OHNS (oil-hardening non-shrinking) in the GCC and India. 1.2510 contains 0.90–1.05% carbon, 1.00–1.20% manganese, 0.50–0.70% chromium, 0.50–0.70% tungsten and 0.05–0.15% vanadium. Manganese and chromium give enough hardenability for an oil or hot-bath quench, which keeps distortion and cracking risk low, while tungsten forms hard carbides that improve wear resistance and edge retention, and vanadium refines the grain. Supplied soft annealed at 229 HB maximum, it machines easily and is hardened from 780–820°C to about 64 HRC, then tempered at 150–250°C to a working hardness of roughly 58–63 HRC. O1 offers an excellent balance of cost, machinability, hardness and dimensional stability, and is supplied as round bar, flat bar and precision ground flat stock (gauge plate). Typical uses are gauges, measuring tools, short-run blanking and punching tools, shear and paper knives, thread-rolling dies, bushes and jigs.

Nifty Alloys supplies O1 / 1.2510 tool steel from stock in Dubai, UAE, in round bar, flat bar and ground flat stock, soft annealed. Our precision ground flat stock programme is detailed on our ground flat stock service page. Every supply is dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying chemistry (1.2510 or O1 as supplied) and annealed hardness with full traceability to the mill; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.95 %
C

Carbon

0.9 – 1.05 %

0.25 %
Si

Silicon

0.15 – 0.35 %

1.1 %
Mn

Manganese

1 – 1.2 %

0.6 %
Cr

Chromium

0.5 – 0.7 %

0.55 %
W

Tungsten

0.5 – 0.7 %

0.1 %
V

Vanadium

0.05 – 0.15 %

P

Phosphorus

≤ 0.035 %

S

Sulfur

≤ 0.035 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 4957

EN

Revision: EN ISO 4957 — current edition

Tool steels — specification for chemical composition, heat treatment, and properties of tool steels including cold work, hot work, and high-speed grades.

Published as BS EN ISO 4957; leading BS dropped to match house style. European standard governing 1.2379 (X153CrMoV12) and other DIN tool steel grades. Supersedes former DIN 17350 for tool steels. Referenced in European and Middle Eastern engineering procurement. Equivalent German standard: DIN EN ISO 4957.

Available Forms

Flat Bar

5–100 mm. Thickness; width to order.

Ground Flat Stock (Gauge Plate)

1–50 mm. Thickness, precision ground; standard 500 mm / 1000 mm lengths — see /services/ground-flat-stock.

Round Bar

3–300 mm. Diameter, annealed; drill rod in small sizes.

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A, 229 HB max) — standard stocked condition, including precision ground flat stock.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 4957

Designations & Equivalents

StandardDesignationNotes
EN / Werkstoff1.2510Material number — primary chemistry on this page
EN Name100MnCrW4EN ISO 4957 steel name
AISI / SAEO1ASTM A681 — near equivalent
UNST31501Unified Numbering System (O1)
BSBO1Former BS 4659 designation — superseded by BS EN ISO 4957
JISSKS3 — nearestJapanese designation
Common Name90MWCV5(AFNOR) French designation
Common Name9CrWMn — nearest(GB) Chinese designation
Common NameO1 tool steel / oil hardening steel / gauge plate / ground flat stock / OHNSBuyer search terms (OHNS = oil-hardening non-shrinking, common in India and the GCC)

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry (1.2510 or O1 as supplied) and annealed hardness.

Specifications

Mechanical Properties

Values per EN ISO 4957. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN ISO 4957
Hardness229 HBmaxSoft annealed (+A)EN ISO 4957 maximum (producers quote 220–230 HB max).
Hardness64 HRCtypicalHardened 780–820°C, oil / hot bath, as quenchedGuidance.
Hardness58–63 HRCAfter tempering 150–300°CTypical working range — guidance.

Physical Properties

PropertyAnnealed (+A) | EN ISO 4957
Densityat 20°C7.85 g/cm³

Service Conditions

Service Temperature

Notes

Cold-work tool steel tempered at 150–250°C; hardness falls if tools run above the tempering temperature (≈ 56 HRC at 350°C). Not for hot-work service — use H13 / 1.2344 for elevated-temperature tooling.

Corrosion Performance

General corrosion

Store dry; protect ground surfaces with rust-preventive oil.

Pitting resistance

Not corrosion resistant; ground flat stock and finished tools rust quickly in humid, coastal UAE and GCC conditions — keep oiled and wrapped.

Additional notes

Not applicable — not a stainless steel.

Heat Treatment

HEAT TREATMENT GUIDE — O1 / 1.2510 / 100MnCrW4

Soft annealing: 740–770°C, controlled slow furnace cooling — 229 HB max (+A). Stress relieving: about 600–650°C, 1–2 h after through-heating, slow furnace cooling — after heavy machining. Hardening: preheat in steps (about 400°C and 650°C), austenitise at 780–820°C, hold 15–30 min after through-heating; quench in oil (interrupt at about 250°C) or hot bath at about 180–220°C — about 64 HRC as quenched. Tempering: immediately after quenching, at least 1 h per 20 mm, minimum 2 h — typical: 150°C ≈ 63 HRC, 200°C ≈ 62 HRC, 250°C ≈ 60 HRC, 300°C ≈ 58 HRC. Working hardness usually 58–63 HRC. Dimensional stability: oil or hot-bath quenching gives low, predictable size change — the basis of the "non-shrinking" (OHNS) name.

ENGINEERING NOTES
Weldability
Poor

Tool repair welding only, with a qualified procedure: preheat to about 300–500°C, weld at that temperature with a suitable tool-steel or hard-facing filler, and stress relieve or temper immediately afterwards (on hardened tools, temper at max. about 300°C after welding). High carbon makes the weld zone prone to cracking.

Filler metals
  • Matching O1-type filler rod · Tool-steel repair / TIGEdge repair of hardened tools with preheat and post-weld temper
  • Cr-Mo alloy electrode · Cr-Mo repair electrodeRepairs on annealed material before hardening
Machinability
Good

Good machinability in the annealed condition (229 HB max) — one of the easiest tool steels to machine. Stress relieve at about 600–650°C after heavy machining, finish-machine, then harden. Ground flat stock is supplied ready for marking out and machining with minimal stock removal. After hardening, finish by grinding.

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

O1 / 1.2510 is used for gauges and measuring tools, short- and medium-run blanking and punching tools, shear and paper knives, thread-rolling dies, taps, drill bushes, jigs and fixtures. It hardens in oil to about 64 HRC with low distortion and machines easily when annealed. In the UAE and GCC it is a toolroom staple, especially as precision ground flat stock (gauge plate).

Get in touch

Elevateyourprojectswithoursuperiorsteel