Alloy Steel dealers in UAE

AISI 6150 / 51CrV4 / 1.8159 Spring Steel | Supplier in UAE & GCC

AISI 6150 / 51CrV4 (1.8159) — Cr-V spring and engineering steel: 248 HB max annealed, 800–1300 MPa Q&T; springs, torsion bars, shafts and gears.

Industries Served

Automotive
Heavy Engineering
Manufacturing
Construction
Mining

Overview

AISI 6150 / 51CrV4 (1.8159, formerly 50CrV4, BS 735A51 / EN47, JIS SUP10) is a chromium-vanadium spring and engineering steel, supplied in Europe to EN ISO 683-2 (formerly EN 10083-3) and EN 10089 for springs, and in the US to ASTM A29 chemistry. It contains 0.47–0.55% carbon, 0.90–1.20% chromium and 0.10–0.25% vanadium: chromium raises hardenability and fatigue strength, while vanadium refines the grain, resists softening during tempering and improves toughness and shock resistance. Supplied annealed at 248 HB maximum for machining and forming, it is hardened from 820–870°C in oil and tempered to suit the duty — high tempering gives 800–1300 MPa engineering strength depending on section (EN ISO 683-2 +QT), while lower tempering produces the high elastic limit and fatigue resistance needed for leaf, coil and torsion-bar springs. The result is a tough, fatigue-resistant steel for springs, torsion bars, stabiliser bars, highly stressed shafts, gears and pins. 6150 and 51CrV4 are close but not identical in chromium and vanadium; the mill certificate states which was supplied.

Nifty Alloys supplies AISI 6150 / 51CrV4 spring steel from stock in Dubai, UAE, in round bar, flat bar and plate, annealed as standard, with quenched and tempered material on request. Bars and plate are cut to size and dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying chemistry (51CrV4 or 6150 as supplied), condition and hardness, with tensile and impact results for heat-treated material; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.51 %
C

Carbon

0.47 – 0.55 %

0.25 %
Si

Silicon

≤ 0.4 %

0.9 %
Mn

Manganese

0.7 – 1.1 %

1.05 %
Cr

Chromium

0.9 – 1.2 %

0.15 %
V

Vanadium

0.1 – 0.25 %

P

Phosphorus

≤ 0.025 %

S

Sulfur

≤ 0.025 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

EN ISO 683-2

EN

Revision: EN ISO 683-2:2018

Heat-treatable steels, alloy steels and free-cutting steels — Part 2: Alloy steels for quenching and tempering.

European standard governing 25CrMo4 (1.7218). Defines chemical composition, mechanical properties per condition, and delivery requirements. Replaces former EN 10083-1.

Available Forms

Round Bar

10–200 mm. Diameter, annealed. [VERIFY — stock range not confirmed]

Flat Bar

5–60 mm. Thickness; width to order. [VERIFY — stock range not confirmed]

Plate / Block

3–100 mm. Thickness, annealed; cut to size. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed (+A, 248 HB max) — standard stocked condition for bar and plate. Quenched & Tempered on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

EN ISO 683-2

Designations & Equivalents

StandardDesignationNotes
AISI / SAE6150US designation — ASTM A29 chemistry
UNSG61500Unified Numbering System
DIN51CrV4 (formerly 50CrV4)EN ISO 683-2 / EN 10089 — primary chemistry on this page
EN / Werkstoff1.815951CrV4 material number
BS735A51 / 735A50 / EN47BS 970 designations (withdrawn standard)
JISSUP10Japanese spring steel designation
Common Name50CrVA(GB) Chinese designation
Common Name51CV4 / 50CV4(AFNOR) French designations
Common NameSpring SteelRegister-required buyer term
Common NameChrome vanadium steel / CrV spring steel / 6150 spring steel / 51CrV4 spring steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition and hardness; tensile and impact for Q&T material.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — Not a sour-service grade: spring and Q&T conditions far exceed the 22 HRC limit for low-alloy steels, and high-strength springs are prone to sulphide stress cracking.

Specifications

Mechanical Properties

Values per EN ISO 683-2. Bar length compares conditions within each row.

PropertyAnnealed (+A) | EN ISO 683-2Quenched & Tempered (+QT) | EN ISO 683-2
Hardness248 HBmaxSoft annealed (+A)EN ISO 683-2 maximum.–
Tensile Strength (UTS)–1100–1300 MPaUp to 16 mmEN ISO 683-2.
Tensile Strength (UTS)–1000–1200 MPaOver 16 to 40 mmEN ISO 683-2.
Tensile Strength (UTS)–900–1100 MPaOver 40 to 100 mmEN ISO 683-2; 850–1000 MPa at 100–160 mm, 800–950 MPa at 160–250 mm.
Yield Strength (0.2% Proof Stress)–800 MPaminOver 16 to 40 mmEN ISO 683-2 minimum; 900 up to 16 mm, 700 at 40–100, 650 at 100–160, 600 at 160–250 mm.
Elongation–10 %minA (5.65√So) — over 16 to 40 mmEN ISO 683-2; 9% up to 16 mm, 12% at 40–100 mm, 13% above.
Reduction of Area–45 %minOver 16 to 40 mmEN ISO 683-2; 40% up to 16 mm, 50% above 40 mm.
Impact Energy (Charpy V-notch)–30 JminOver 16 mm, room tempEN ISO 683-2 minimum (not specified up to 16 mm).

Physical Properties

PropertyAnnealed (+A) | EN ISO 683-2Quenched & Tempered (+QT) | EN ISO 683-2
Densityat 20°C7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C205 GPa205 GPa
Shear Modulusat 20°C80 GPa80 GPa
Coefficient of Thermal Expansionat 20–100°C12.1 µm/m·°C12.1 µm/m·°C

Service Conditions

Service Temperature

Min -25 °CMax 250 °C

Notes

[VERIFY — maxServiceTempC 250: continuous spring service limit not confirmed] Producer data gives a lowest application temperature of about -25°C for 51CrV4. Springs lose load (relax) progressively at elevated temperature; keep service well below the tempering temperature. For high-temperature springs, use a heat-resistant spring grade.

Corrosion Performance

General corrosion

Corrodes like other low-alloy steels. Hardened springs are highly susceptible to hydrogen embrittlement — avoid acid pickling and electroplating, or bake immediately after plating.

Pitting resistance

No pitting resistance. Corrosion pits act as fatigue-crack starters in springs — protect with paint, powder coating, phosphate or zinc systems in the humid, coastal UAE and GCC climate.

Additional notes

Not applicable — low-alloy steel.

Heat Treatment

HEAT TREATMENT GUIDE — AISI 6150 / 51CrV4 / 1.8159

Forging / rolling: 1050–850°C. Normalising: 870–900°C, air cool. Soft annealing: 680–720°C (range 640–720°C), slow furnace cool — 248 HB max (+A). Hardening: 820–870°C — quench in oil (water quenching not allowed). Tempering for engineering strength (+QT): 540–680°C — EN ISO 683-2 ranges: up to 16 mm 1100–1300 MPa; 16–40 mm 1000–1200 MPa; 40–100 mm 900–1100 MPa; 100–160 mm 850–1000 MPa; 160–250 mm 800–950 MPa. Tempering for springs: lower tempering temperatures to reach the spring hardness specified by the spring designer (typically mid-40s to around 50 HRC) [VERIFY — spring tempering range not confirmed]. Temper immediately while parts are hand-warm; soak 1 h per 25 mm (2 h minimum). Surface: avoid decarburisation during heating; shot peening after heat treatment improves spring fatigue life.

ENGINEERING NOTES
Weldability
Poor

Not recommended for welding — 0.5% carbon with chromium gives a hard, crack-prone heat-affected zone, and welding destroys spring properties. If unavoidable on annealed material, preheat to about 250–350°C [VERIFY — preheat range not confirmed], use low-hydrogen consumables, cool slowly and re-heat-treat the part. Never weld hardened springs.

Filler metals
  • E9018-B3 · AWS A5.5 / SMAWLow-hydrogen Cr-Mo electrode for repairs on annealed material; re-heat-treat after
  • ER80S-B2 · AWS A5.28 / TIG / MIGCr-Mo wire for annealed material repairs; preheat essential
  • E312-16 · AWS A5.4 / SMAWAustenitic electrode for non-load-bearing attachments where hardening cannot follow
Machinability
Fair

Machine, form and drill in the annealed condition (248 HB max) with carbide or HSS tooling and coolant. Q&T material at engineering strength (up to about 1100 MPa) machines with carbide; spring-hardened material is ground only. Avoid surface decarburisation and tool marks on springs — they reduce fatigue life; shot peen finished springs where possible.

Applications

  • Leaf springs and parabolic springs for trucks, trailers and rail vehicles
  • Heavy-duty coil springs and valve springs
  • Torsion bars, stabiliser (anti-roll) bars and suspension components
  • Highly stressed shafts, gears, pinions and splined parts
  • Disc springs, Belleville washers and spring clips
  • Scraper blades, grader edges and wear strips for earthmoving equipment
  • Hand tools, wrenches and chisels needing toughness
  • Clutch and brake components exposed to shock and vibration
  • Spring pins and retaining components for GCC machinery and plant
  • Agricultural and mining tine and blade components

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

AISI 6150 / 51CrV4 is used for leaf, parabolic and coil springs, torsion and stabiliser bars, disc springs and spring clips, and for highly stressed engineering parts such as shafts, gears, pins, scraper blades and hand tools. Its chromium and vanadium give high fatigue strength with good toughness and shock resistance. In the UAE and GCC it is used for truck and trailer springs, earthmoving wear blades and heavy machinery parts.

Get in touch

Elevateyourprojectswithoursuperiorsteel