Alloy Steel dealers in UAE

708M40 / EN19A / 708M40T Alloy Steel | Supplier in UAE & GCC

708M40 / EN19A / 708M40T — 1% Cr-Mo high-tensile steel (0.15–0.25% Mo): Condition T 850–1000 MPa, 248–302 HB; shafts, gears, studs and axles.

Industries Served

Automotive
Heavy Engineering
Oil & Gas
Manufacturing
Mining

Overview

708M40 (formerly EN19A, supplied pre-hardened as 708M40T) is a 1% chromium-molybdenum high-tensile alloy steel to BS 970, containing 0.36–0.44% carbon, 0.70–1.00% manganese, 0.90–1.20% chromium and 0.15–0.25% molybdenum. It is the lower-molybdenum sister of 709M40 (EN19, 0.25–0.35% Mo); its molybdenum range matches AISI 4140 and its analysis lies within the European 42CrMo4 limits, so for most buyers it serves the same applications — see our AISI 4140 / 42CrMo4 / EN19 page for that grade family. Chromium gives hardenability and wear resistance, while molybdenum adds strength and reduces temper embrittlement. Supplied hardened and tempered to Condition T, 708M40T delivers 850–1000 MPa tensile strength, 650 MPa minimum yield, 13% elongation and 248–302 HB, with good ductility, shock resistance and wear resistance, and it is readily machinable in this condition. It can also be flame or induction hardened, or nitrided, for extra surface wear resistance. Typical uses are shafts, axles, gears, studs, bolts and general high-tensile engineering parts. BS 970 is withdrawn; 708M40 continues as a legacy specification.

Nifty Alloys supplies 708M40 / EN19A alloy steel from stock in Dubai, UAE, in round bar, hardened and tempered to Condition T as standard, with annealed material on request. Bars are cut to length and dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying 708M40 chemistry, condition, tensile, impact and hardness results with full traceability to the mill; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.4 %
C

Carbon

0.36 – 0.44 %

Si

Silicon

0.1 – 0.35 %

Mn

Manganese

0.7 – 1 %

1.05 %
Cr

Chromium

0.9 – 1.2 %

0.2 %
Mo

Molybdenum

0.15 – 0.25 %

P

Phosphorus

≤ 0.035 %

S

Sulfur

≤ 0.04 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

BS 970-1 (withdrawn)

Other

Revision: BS 970-1:1996 (withdrawn — legacy specification)

Available Forms

Round Bar

16–250 mm. Diameter, Condition T; bright drawn in smaller sizes. Condition T subject to ruling section. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
H&T Condition T (708M40T) — standard stocked condition. Annealed on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

BS 970-1 (withdrawn)

Designations & Equivalents

StandardDesignationNotes
BS708M40 / 708M40TBS 970 designation (withdrawn standard) — governing chemistry; T = Condition T
BSEN19AOriginal BS 970:1955 designation
BS709M40 / EN19Sister grade with higher molybdenum (0.25–0.35%) — separate page
EN Name42CrMo4 / 1.7225(EN (closely related)) Closely related — 708M40 chemistry lies within 42CrMo4 limits. Main page: AISI 4140 / 42CrMo4 / EN19
AISI / SAE4140Same Mo range (0.15–0.25%); Cr and Mn ranges differ slightly. Main page: AISI 4140 / 42CrMo4 / EN19
Common Name42CD4(AFNOR) French designation
Common NameEN19A round bar / 708M40T / high tensile steel / chrome moly steelBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — 708M40 chemistry, condition, tensile, impact and hardness.

Specifications

Mechanical Properties

Values per BS 970-1 (withdrawn). Bar length compares conditions within each row.

PropertyH&T Condition T | BS 970-1Annealed | BS 970-1
Tensile Strength (UTS)850–1000 MPaCondition TBS 970 range.–
Yield Strength (0.2% Proof Stress)650 MPaminCondition TPublished minimum.–
Elongation13 %minA (5.65√So)Published minimum.–
Impact Energy (Charpy V-notch)35 JminRoom temp, KCVPublished value.–
Hardness248–302 HBCondition TBS 970 range.–AnnealedMaximum reported on MTC [VERIFY — annealed hardness limit not confirmed].

Physical Properties

PropertyH&T Condition T | BS 970-1Annealed | BS 970-1
Densityat 20°C7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C205 GPa205 GPa
Thermal Conductivityat 20°C42 W/m·K42 W/m·K
Coefficient of Thermal Expansionat 20–100°C12.3 µm/m·°C12.3 µm/m·°C

Service Conditions

Service Temperature

Max 400 °C

Notes

[VERIFY — maxServiceTempC 400: continuous load-bearing limit not confirmed] Do not use at or near the tempering temperature, and avoid prolonged exposure in the temper-embrittlement range. Specify impact testing for sub-zero service.

Corrosion Performance

General corrosion

Corrodes like other low-alloy steels. High-tensile fasteners are susceptible to hydrogen embrittlement from electroplating — bake after plating.

Pitting resistance

No pitting resistance. Rusts in humid and coastal UAE and GCC atmospheres; protect with oil, paint, phosphate or plating.

Additional notes

Not applicable — low-alloy steel.

Heat Treatment

HEAT TREATMENT GUIDE — 708M40 / EN19A / 708M40T

Forging: preheat carefully, forge at 850–1200°C; do not forge below 850°C; cool slowly in still air. Annealing: on request — softened for machining [VERIFY — annealing cycle not confirmed]. Hardening: heat slowly to 860–890°C, soak, quench in oil. Temper as soon as parts reach hand warm. Tempering: select temperature for the required condition — Condition T 850–1000 MPa (248–302 HB). Avoid the temper-embrittlement range. Surface hardening: flame or induction hardening, or nitriding of the Condition T bar for added wear resistance. Stress relieving: below the tempering temperature after heavy machining or welding.

ENGINEERING NOTES
Weldability
Fair

Weldable with precautions — 0.40% carbon with chromium and molybdenum gives a hardenable HAZ. Preheat to about 200–300°C [VERIFY — preheat range not confirmed], use low-hydrogen Cr-Mo consumables, maintain interpass at preheat and cool slowly, then stress relieve below the tempering temperature. Welding 708M40T alters HAZ properties; avoid welding highly stressed parts.

Filler metals
  • E9018-B3 · AWS A5.5 / SMAWLow-hydrogen Cr-Mo electrode; preheat and PWHT required
  • ER80S-B2 · AWS A5.28 / TIG / MIG1.25Cr-0.5Mo wire for GTAW / GMAW
  • E7018 · AWS A5.1 / SMAWUnder-matching electrode for non-critical repairs
Machinability
Good

Readily machinable in Condition T (248–302 HB) with carbide tooling; annealed material machines more easily for heavy roughing.

Applications

  • Drive shafts, propeller shafts and gearbox shafts
  • Axles and stub axles for vehicles and material-handling equipment
  • Gears, pinions and sprockets in moderate sections
  • High-tensile studs, bolts and nuts for GCC plant maintenance
  • Hydraulic cylinder rods and piston rods
  • Couplings, hubs and flanges for rotating equipment
  • Spindles and arbors for machine tools
  • Connecting rods and crankshafts for engines
  • Non-sour oilfield and mining tool components
  • Induction-hardened or nitrided wear parts with a tough core

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

708M40 / EN19A is used for high-tensile engineering parts such as drive and gearbox shafts, axles, gears and pinions, studs and bolts, hydraulic rods, couplings, spindles and connecting rods. Supplied as 708M40T it gives 850–1000 MPa tensile strength with good ductility and shock resistance. In the UAE and GCC it is used for plant maintenance, pump and gearbox components and general heavy engineering.

Get in touch

Elevateyourprojectswithoursuperiorsteel