Alloy Steel dealers in UAE

EN26 / 826M40 / 40NiMoCr10-5 Alloy Steel | Supplier in UAE & GCC

EN26 / 826M40 (40NiMoCr10-5) — 2.5% Ni-Cr-Mo high-tensile steel: Condition V 1000–1150 MPa to 250 mm ruling section; heavy shafts, gears and studs.

Industries Served

Oil & Gas
Power Generation
Heavy Engineering
Aerospace & Defence
Mining
Manufacturing

Overview

EN26 (BS 970 826M40, closely matching DIN 40NiMoCr10-5 / 1.6745, Australian X9940, aerospace BS S98 / S99) is a 2.5% nickel-chromium-molybdenum high-hardenability, high-tensile alloy steel, supplied hardened and tempered. It contains 0.36–0.44% carbon, 2.30–2.80% nickel, 0.50–0.80% chromium and 0.45–0.65% molybdenum: compared with EN24, the extra nickel and molybdenum give deeper hardening and better toughness in very large sections, while molybdenum suppresses temper embrittlement. In Condition V, EN26 holds 1000–1150 MPa tensile strength and 293–352 HB right through a 250 mm limiting ruling section, and higher conditions reach 1080–1230 MPa (W), 1150–1300 MPa (X) and 1550 MPa minimum (Z) in smaller sections. Pre-hardened bar can be further flame or induction hardened, or nitrided, although nickel slows nitrogen diffusion. EN26 is chosen for heavy-duty shafts, axles, connecting rods, spindles, high-tensile studs and die holders where EN24 lacks the section capability. BS 970 is withdrawn, and 826M40 continues as a legacy specification.

Nifty Alloys supplies EN26 / 826M40 / 40NiMoCr10-5 alloy steel from stock in Dubai, UAE, in round bar and forgings, hardened and tempered to Condition V as standard, with Condition W, X, Z and annealed material on request. Bars are cut to length and dispatched with EN 10204 3.1 Mill Test Certificates as standard, certifying 826M40 chemistry, condition, tensile, impact and hardness results with full traceability to the mill; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list or drawing to request a quote — quotations are turned around the same day.

Chemical Composition

0.4 %
C

Carbon

0.36 – 0.44 %

Si

Silicon

0.1 – 0.35 %

Mn

Manganese

0.45 – 0.7 %

2.55 %
Ni

Nickel

2.3 – 2.8 %

0.65 %
Cr

Chromium

0.5 – 0.8 %

0.55 %
Mo

Molybdenum

0.45 – 0.65 %

P

Phosphorus

≤ 0.035 %

S

Sulfur

≤ 0.04 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

BS 970-1 (withdrawn)

Other

Revision: BS 970-1:1996 (withdrawn — legacy specification)

Available Forms

Forging

200–1000 mm. Forged bars, blocks and rings to order. [VERIFY — stock range not confirmed]

Round Bar

25–450 mm. Diameter, Condition V — guaranteed to 250 mm ruling section; larger sizes at reduced core properties. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
H&T Condition V (1000–1150 MPa) — standard stocked condition. Condition W, X, Z and annealed on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes

Key standards

BS 970-1 (withdrawn)

Designations & Equivalents

StandardDesignationNotes
BSEN26 / EN26V / EN26WOriginal BS 970:1955 designation; letter = strength condition
BS826M40 / 826M40V / 826M40WBS 970 designation (withdrawn standard) — governing chemistry
DIN40NiMoCr10-5Closely matching DIN grade — same C, Mn, Ni, Cr, Mo ranges; tighter P / S
EN / Werkstoff1.674540NiMoCr10-5 material number
Common NameBS S98 / BS S99(BS Aerospace) UK aerospace equivalents of 826M40 (tighter P / S, controlled Al) — aliases only
Common NameX9940(AS) Australian Standard AS 1444
Common NameEN26 round bar / 2.5% nickel chrome moly steel / high tensile steel / EN26VBuyer search terms

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — 826M40 chemistry, condition, tensile, impact and hardness.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Not Applicable — Not acceptable under ISO 15156-2 general requirements: carbon and low-alloy steels must contain < 1% Ni (EN26 has 2.30–2.80%), and Condition V (293–352 HB) exceeds 22 HRC. Not a sour-service grade.

Specifications

Mechanical Properties

Values per BS 970-1 (withdrawn). Bar length compares conditions within each row.

PropertyH&T Condition V | BS 970-1Annealed | BS 970-1H&T Condition W / X / Z | BS 970-1
Tensile Strength (UTS)1000–1150 MPaCondition V — up to 250 mm LRSBS 970 / AS 1444 range.–1080–1230 MPaCondition W — up to 250 mm LRSBS 970 / AS 1444 range (some sources: 1075–1225).
Tensile Strength (UTS)––1150–1300 MPaCondition X — up to 150 mm LRSBS 970 / AS 1444 range.
Tensile Strength (UTS)––1550 MPaminCondition Z — up to 100 mm LRSBS 970 / AS 1444 minimum.
Yield Strength (0.2% Proof Stress)835 MPaminCondition V — up to 150 mm LRSAS 1444 / BS 970 minimum.–925 MPaminCondition W — up to 150 mm LRSMinimum; 910 MPa over 150–250 mm. Condition X: 1005 MPa.
Yield Strength (0.2% Proof Stress)820 MPaminCondition V — over 150 to 250 mm LRSAS 1444 / BS 970 minimum.––
Elongation12 %minA (5.65√So)Published minimum.–11 %minCondition W — A (5.65√So)Published minimum; Condition Z: 7%.
Impact Energy (Charpy V-notch)42 JminRoom temp, KCVPublished Condition V value.–40 JminCondition W — up to 150 mm, room tempPublished minimum; 27 J over 150–250 mm. Condition Z: 13 J.
Hardness293–352 HBCondition VBS 970 / AS 1444 range (about 31–38 HRC).–AnnealedMaximum reported on MTC [VERIFY — annealed hardness limit not confirmed].311–375 HBCondition WRange; Condition X: 340–401 HB; Condition Z: 444 HB min.

Physical Properties

PropertyH&T Condition V | BS 970-1Annealed | BS 970-1H&T Condition W / X / Z | BS 970-1
Densityat 20°C7.85 g/cm³7.85 g/cm³7.85 g/cm³
Modulus of Elasticityat 20°C205 GPa205 GPa205 GPa
Thermal Conductivityat 20°C35 W/m·K35 W/m·K35 W/m·K
Coefficient of Thermal Expansionat 20–100°C12 µm/m·°C12 µm/m·°C12 µm/m·°C

Service Conditions

Service Temperature

Max 400 °C

Notes

[VERIFY — maxServiceTempC 400: continuous load-bearing limit not confirmed in a code source] Do not use at or near the tempering temperature. Nickel gives good low-temperature toughness; specify impact testing at the service temperature for sub-zero duty. Avoid prolonged exposure in the temper-embrittlement range. Not a creep-resisting grade.

Corrosion Performance

General corrosion

Corrodes like other low-alloy steels. Conditions W and above are susceptible to hydrogen embrittlement from electroplating or cathodic protection — bake after plating.

Pitting resistance

No pitting resistance. Rusts in humid and coastal UAE and GCC atmospheres; protect with oil, paint, phosphate, nitriding or plating.

Additional notes

Not applicable — low-alloy steel.

Heat Treatment

HEAT TREATMENT GUIDE — EN26 / 826M40 / 40NiMoCr10-5

Forging: heat to 1150–1200°C maximum, hold until uniform, forge immediately; do not forge below about 850°C; cool slowly. Annealing: 790–840°C — hold until uniform — furnace cool. Hardening: about 820–850°C — quench in oil or polymer [VERIFY — exact range not confirmed]. Temper immediately. Tempering: select from a tempering chart for the required condition — soak about 2 h per 25 mm — air cool. Avoid tempering in the 250–400°C range. Conditions and limiting ruling sections (BS 970 / AS 1444): V 1000–1150 MPa to 250 mm; W 1080–1230 MPa to 250 mm; X 1150–1300 MPa to 150 mm; Z 1550 MPa min to 100 mm. Surface hardening: flame or induction hardening of pre-hardened bar; nitriding possible, but nickel slows nitrogen diffusion — expect lower case hardness or longer cycles; temper above the nitriding temperature first. Stress relieving: below the last tempering temperature after heavy machining.

ENGINEERING NOTES
Weldability
Poor

Difficult to weld — 0.40% carbon with nickel, chromium and molybdenum gives very high hardenability and a crack-prone HAZ. Avoid welding wherever possible. If unavoidable: weld annealed material, preheat to about 300–350°C [VERIFY — preheat range not confirmed] and hold interpass at preheat, use dry low-hydrogen consumables, cool slowly and immediately stress relieve or re-harden and temper. Welding H&T bar leaves an uncontrolled HAZ.

Filler metals
  • E11018-M · AWS A5.5 / SMAWLow-hydrogen high-strength electrode for near-matching strength; preheat and PWHT essential
  • ER120S-1 · AWS A5.28 / TIG / MIGHigh-strength wire for near-matching joints
  • E8018-B2 · AWS A5.5 / SMAWUnder-matching repair electrode where lower joint strength is acceptable
Machinability
Fair

Condition V (293–352 HB) machines with carbide tooling, rigid set-ups and reduced speeds; W and above need hardened-steel carbide grades. Annealed material machines more easily for heavy roughing before heat treatment. Allow for distortion if hardening after machining.

Applications

  • Heavy-duty drive shafts, pinion shafts and axles in large sections
  • High-tensile studs, bolts and tie rods for offshore and process plant
  • Connecting rods, crankshafts and spindles for engines and compressors
  • Die holders, bolsters and tool holders in forging and press shops
  • Gears and gear shafts for mining and heavy industrial gearboxes
  • Hydraulic rams and press columns under high load
  • Large rolls, couplings and hubs for GCC steel and heavy plants
  • Aerospace and defence parts to BS S98 / S99 chemistry
  • Nitrided or induction-hardened wear parts with a strong core
  • Non-sour oilfield tool bodies and heavy machinery components

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

EN26 / 826M40 is used for heavily loaded parts in large sections: drive and pinion shafts, axles, connecting rods, spindles, high-tensile studs, die holders, hydraulic rams and heavy gears. Supplied in Condition V it holds 1000–1150 MPa tensile strength through a 250 mm ruling section. In the UAE and GCC it is used for offshore and process-plant studs, heavy machinery shafts and forging-shop tooling.

Get in touch

Elevateyourprojectswithoursuperiorsteel