Nickel Alloys dealers in UAE

Monel 400 / Alloy 400 / 2.4360 Nickel-Copper Alloy | Supplier in UAE & GCC

Alloy 400 / 2.4360 / UNS N04400 — nickel-copper alloy: excellent seawater, HF acid and alkali resistance, chloride-SCC immune; marine, valves, pumps.

Industries Served

Marine
Oil & Gas
Petrochemical
Power Generation
Aerospace & Defence

Overview

Alloy 400 (UNS N04400, EN 2.4360 / NiCu30Fe, ASTM B164 / B127 / B564, AMS 4675; widely known by the trade name Monel 400) is a solid-solution nickel-copper alloy containing at least 63% nickel and 28.0–34.0% copper, with up to 2.5% iron and 2.0% manganese. It cannot be hardened by heat treatment; strength is raised only by cold working. Its nickel-copper chemistry gives excellent resistance to flowing seawater and brackish water, steam, alkalis, neutral and alkaline salts, and reducing acids — it is one of the few alloys suitable for hydrofluoric acid in all concentrations, and performs well in de-aerated sulphuric and hydrochloric acids. It is virtually immune to chloride stress corrosion cracking. The trade-off is poor resistance to oxidising media: nitric acid, ammonia systems and oxidising salts such as ferric and cupric chlorides attack it rapidly, and aeration increases corrosion rates in acids. Annealed rod and bar provides 480 MPa minimum tensile and 170 MPa minimum yield strength (ASTM B164), rising to 600 / 415 MPa in the cold-drawn, stress-relieved condition. It retains good properties from subzero temperatures to about 480°C in air, and is weakly magnetic at room temperature. Typical uses are marine fixtures and propeller shafts, seawater valves and pumps, heat exchangers, HF-alkylation units, crude-oil distillation towers and chemical-process equipment.

Nifty Alloys supplies Alloy 400 / 2.4360 from Dubai, UAE, in round bar, plate, sheet and forgings — annealed as standard, with cold-drawn / stress-relieved bar and AMS 4675 supply on request. Every supply carries an EN 10204 3.1 Mill Test Certificate as standard; EN 10204 3.2 third-party inspection is available on request. We deliver across the UAE within 24–48 hours, to Saudi Arabia, Kuwait, Qatar, Oman and Bahrain within 3–5 working days, and export to Europe, India and Africa. Send your size list and condition to request a quote — quotations are turned around the same day. Monel® is a registered trademark of its owner.

Chemical Composition

66 %
Ni

Nickel

≥ 63 %

31 %
Cu

Copper

28 – 34 %

1.5 %
Fe

Iron

≤ 2.5 %

1 %
Mn

Manganese

≤ 2 %

0.1 %
C

Carbon

≤ 0.3 %

Si

Silicon

≤ 0.5 %

S

Sulfur

≤ 0.024 %

Typical value Range (min–max) Minimum (≥) Maximum (≤) Hover / tap for notes

Standard

ASTM B164

Other

Revision: ASTM B164 — current edition

Available Forms

Forging

100–800 mm. Forged discs, rings and blocks to order. [VERIFY — supply range not confirmed]

Plate / Block

3–50 mm. Thickness; cut to size. [VERIFY — stock range not confirmed]

Round Bar

6–300 mm. Diameter, annealed or cold drawn / stress relieved. [VERIFY — stock range not confirmed]

Sheet

0.5–3 mm. Thickness. [VERIFY — stock range not confirmed]

Stock & delivery

Stock location
Dubai, UAE
In stock
Annealed bar [VERIFY — stocked forms]; cold drawn / stress relieved and AMS 4675 material on request.
Delivery UAE
24–48 hours
Delivery GCC
3–5 working days — Saudi Arabia, Kuwait, Qatar, Oman, Bahrain
Export
Europe, India, Africa on request
Quotation
Same-day quotation
Minimum order
No minimum order quantity for standard sizes; cut pieces available

Key standards

ASTM B164

Designations & Equivalents

StandardDesignationNotes
UNSN04400Unified Numbering System — primary chemistry
EN / Werkstoff2.4360European material number
EN / Werkstoff2.4361Low-carbon variant (LC-NiCu30Fe)
EN NameNiCu30FeEuropean alloy designation
AMSAMS 4675Bars and forgings (Module 2)
AMSAMS 4544Sheet, strip and plate — aliases only
Common NameQQ-N-281(Federal) Legacy US federal specification — aliases only
ASMESB-164 / SB-127 / SB-564ASME equivalents — aliases only
BSNA13British designation
Common NameNU30(AFNOR) French designation
Common NameAlloy 400 / Nickel 400 / NiCu 400 / nickel-copper alloyBuyer search terms (trademark used only in SEO / description / FAQ fields)

Compliance & Certification

StandardStatusNotes
EN 10204 3.1SuitableProvided as standard — chemistry, condition and mechanical properties.
EN 10204 3.2ConditionalAvailable on request with independent third-party inspection — specify at order stage.
NACE MR0175 / ISO 15156Requires ConfirmationStockists commonly certify Alloy 400 to MR0175; listing and hardness limit (35 HRC quoted) not confirmed against ISO 15156-3 [VERIFY — current edition].
NACE MR0103 / ISO 17945Requires ConfirmationRefinery sour service — confirm listing and limits [VERIFY].
AMS 4675ConditionalSupplied to AMS 4675 on request — confirm revision.
ASME Section II / VIIISuitableSB-127 / SB-164 / SB-564 material for pressure equipment.

Specifications

Mechanical Properties

Values per ASTM B164. Bar length compares conditions within each row.

PropertyAnnealed | ASTM B164Cold Drawn / Stress Relieved | ASTM B164
Tensile Strength (UTS)480 MPaminRod and bar, all sizesASTM B164 minimum (70 ksi).600 MPaminRounds 12.7–88.9 mmASTM B164 minimum (87 ksi).
Tensile Strength (UTS)–580 MPaminRounds < 12.7 mmASTM B164 minimum (84 ksi); YS 345 MPa, El. 10%.
Yield Strength (0.2% Proof Stress)170 MPaminRod and bar, all sizesASTM B164 minimum (25 ksi).415 MPaminRounds 12.7–88.9 mmASTM B164 minimum (60 ksi).
Elongation35 %min50 mm / 4DASTM B164 minimum.20 %minRounds 12.7–88.9 mmASTM B164 minimum.
Hardness60–80 HRBAnnealedTypical range — guidance.–

Physical Properties

PropertyAnnealed | ASTM B164Cold Drawn / Stress Relieved | ASTM B164
Densityat 20°C8.8 g/cm³8.8 g/cm³
Modulus of Elasticityat 20°C179 GPa179 GPa
Thermal Conductivityat 20°C21.8 W/m·K21.8 W/m·K
Coefficient of Thermal Expansionat 20–100°C13.9 µm/m·°C13.9 µm/m·°C
Specific Heat Capacityat 20°C427 J/kg·K427 J/kg·K
Electrical Resistivityat 20°C0.55 µΩ·m0.55 µΩ·m

Service Conditions

Service Temperature

Min -196 °CMax 480 °C

Notes

Good mechanical properties from subzero temperatures (no ductile-to-brittle transition) to about 480°C in oxidising air; can be used to about 540°C in reducing atmospheres. Avoid sulphur-bearing atmospheres above about 370°C.

Corrosion Performance

General corrosion

Excellent resistance to seawater, steam, alkalis, neutral salts, hydrofluoric acid and de-aerated sulphuric / hydrochloric acids; virtually immune to chloride SCC. Rapidly attacked by nitric acid, ammonia systems and oxidising salts (ferric, cupric chlorides); aeration increases acid corrosion rates. Susceptible to SCC in moist aerated HF vapour and mercury salts.

Pitting resistance

Excellent resistance in flowing seawater; pitting can occur in stagnant seawater or under deposits.

Additional notes

Not applicable — PREN is not meaningful for nickel-copper alloys.

Heat Treatment

HEAT TREATMENT GUIDE — Alloy 400 / 2.4360 / UNS N04400

Not hardenable by heat treatment — strength increased only by cold work. Annealing: about 870°C (hot- or cold-worked and annealed), air cool or quench — softest condition. Stress relieving: about 540–650°C after cold work, to reduce residual stress without significant loss of strength — removes risk of stress corrosion in aggressive media. Hot working: about 650–1175°C; avoid sulphur-bearing fuels and atmospheres. Welding: no preheat or PWHT required.

ENGINEERING NOTES
Weldability
Excellent

Readily welded by GTAW, GMAW and SMAW using matching ERNiCu-7 / ENiCu-7 fillers; also brazed and soldered. No preheat or PWHT normally required. Joints must be clean and free of sulphur, lead and other low-melting contaminants to avoid embrittlement.

Filler metals
  • ERNiCu-7 · AWS A5.14 / TIG (GTAW) / MIG (GMAW)Matching nickel-copper filler wire
  • ENiCu-7 · AWS A5.11 / SMAWMatching covered electrode
  • ERNi-1 · AWS A5.14 / TIG / MIGFor overlays / dissimilar joints to steel where specified
Machinability
Good

Reasonably machinable for a nickel alloy (class B), best in the cold-drawn / stress-relieved condition. Work hardens — use sharp tools, positive rake, steady feed and generous coolant. Free-machining Alloy 405 (N04405) is the alternative for high-volume machined parts.

Applications

  • Marine fixtures, propeller and pump shafts for GCC vessels
  • Seawater valves, pumps and fittings
  • Heat exchangers, feedwater heaters and condensers
  • HF-alkylation units and hydrofluoric-acid handling equipment
  • Crude-oil distillation towers and refinery overhead systems
  • Chemical-process equipment for alkalis, salts and chlorinated solvents
  • Brine heaters and desalination components
  • Fasteners and springs in corrosive service
  • Aircraft fuel and water tanks and oil-cooler parts (AMS 4675)
  • Gasoline and freshwater tanks and piping

Related grades in Nickel Alloys

Frequently Asked Questions

Quick answers on our grades, certification, supply and lead times.

Still have questions?

Our team responds fast with specifications, certification and stock availability.

Contact our team

Alloy 400 is used for marine fixtures and propeller shafts, seawater valves and pumps, heat exchangers, HF-alkylation units, crude-oil distillation towers, brine heaters and chemical-process equipment handling alkalis, salts and reducing acids. In the UAE and GCC it is common in marine, desalination and refinery applications.

Get in touch

Elevateyourprojectswithoursuperiorsteel